1997 SSANGYONG KORANDO torque

SEATS 9H-3
SSANGYONG MY2002
REPAIR INSTRUCTIONS
KAA9H020
ON-VEHICLE SERVICE
UNIT REPAIR
FRONT SEAT
Removal and Installation Procedure
1. Remove the electrical connector from front seat.
KAA9H030
2. Remove the bolts with the front seat.
Installation Notice
•Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
Tightening Torque19.6 - 31.4 Nm
(14.5 - 23.2 lb-ft)
KAA9H060
FRONT SEAT CUSHION
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
“front seat” in this section.
2. Remove the front seatback. Refer to “Front Seat
back” in this section.
3. Remove the seat cushion bolts.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque16.7 - 25.5 Nm
(12 - 18 lb-ft)

SSANGYONG MY2002
9H-4 SEATS
KAA9H070
FRONT SEAT GUIDE RAIL
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
in this section.
2. Remove the front seat trim. Refer to “front seat
trim” in this section.
3. Remove the bolts and the guide rail.
Installation Notice
KAA9H050
6. Remove the bolts and the seatback.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
7. Installation should follow the removal procedure
in the reverse order.
Tightening Torque34.3 - 55.9 Nm
(25 - 41 lb-ft)
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque17.6 - 25.5 Nm
(12 - 18 lb-ft)
KAA9H040
FRONT SEATBACK
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
“front seat” in this section.
2. Remove the head restraint. Refer to “head
restraint” in this section.
3. Remove the seat recliner lever. Refer to “seat
recliner lever” in this section.
4. Remove the seat trim. Refer to “seat trim” in this
section.
5. Remove the seatback cover.

SSANGYONG MY2002
9H-6 SEATS
KAA9H120
KAA9H130
WALK IN DEVICE
Removal and Installation Procedure
1. Remove the front seat. Refer to “front seat” in this
section.
2. Remove the seat recliner. Refer to “seat recliner”
in this section.
3. Remove the seat trim. Refer to “seat trim” in this
section.
4. Remove the walk in device assembly.
5. Installation should follow the removal procedure
in the reverse order.
FRONT SEAT ARMREST
Removal and Installation Procedure
1. Remove the arm rest cover.
2. Remove the arm rest mounting bolt.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Remove the arm rest.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque17.6 - 25.5 Nm
(12 - 18 lb-ft)
KAA9H180
REAR SEAT ARMREST
Removal and Installation Procedure
1. Push the button in the arm rest.
2. Turn and remove from the side quarter trim panel.
3. Installation should follow the removal procedure
in the reverse order.

SEATS 9H-7
SSANGYONG MY2002


yyyy yyyy yyyy
KAA9H150
KAA9H160
3. Remove the bolts and the rear seat.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
KAA9H140
REAR SEAT
Removal and Installation Procedure
1. Lift up the rear seat from the floor.
2. Remove the bolts.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
50/50 SPLIT REAR SEAT CUSHION
HINGE
Removal and Installation Procedure
1. Remove the bolts and the rear seat cushion hinge.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correctfasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
Tightening Torque19.6 - 31.4 Nm
(14.5 - 23.2 lb-ft)
Tightening Torque19.6 - 31.4 Nm
(14.5 - 23.2 lb-ft)
Tightening Torque34.3 - 53.9 Nm
(25 - 39 lb-ft)

SSANGYONG MY2002
9H-8 SEATS
50/50 SPLIT REAR SEAT CUSHION
LOCK STRIKER
Removal and Installation Procedure
1. Remove the bolts and rear seat cushion lock
striker.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
KAA9H200
2. Remove the child seat anchorage bolt.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
KAA9H190
CHILD SEAT ANCHORAGE
Removal and Installation Procedure
1. Remove the child seat anchorage cover.
Tightening Torque34.3 - 53.9 Nm
(25 - 39 lb-ft)
KAA9H170
Tightening Torque 19 Nm (14 lb-ft)

GLASS AND MIRRORS 9L-9
SSANGYONG MY2002
KAA9L160
KAA9L170
FRONT DOOR GLASS
Removal Procedure
1. Remove the door seal trim. Refer to Section 9P,
Doors.
2. Remove the screws that secure the glass to the
window regulator.
3. Remove the glass from the door.
4. Removal procedure should follow the installation
procedure in the reverse order.
Installation Procedure
1. Install the glass in the door and position the glass
within the window regulator.
Notice: Dissimilar metals in direct contact with
each other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Install the glass to the window regulator with the
screws.
Installation Notice
3. Install the door seal trim. Refer to Section 9P,
Doors.
4. Removal procedure should follow the installation
procedure in the reverse order.
Tightening Torque1.96 - 2.94 Nm
(17.50 - 26.25 lb-in)
KAA9L180
FIXED GLASS
Removal and Installation Procedure
1. Remove the exterior B-pillar molding. Refer to
Section 9M, Exterior Trim.
2. Remove the screws that secure the glass to the
window regulator.
3. Remove the glass from the door.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque 7 Nm (62 lb-in)

SSANGYONG MY2002
9L-10 GLASS AND MIRRORS
KAA9L190
KAA9L200
OUTSIDE REARVIEW MIRROR
Removal and Installation Procedure
1. Remove the tweeter inner cover.
2. Remove the screws with the outside rearview
mirror.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
INSIDE REARVIEW MIRROR
Removal and Installation Procedure
1. Remove the screw with the inside rearview mirror.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
Tightening Torque1.4 - 1.7 Nm
(9 lb-in)
Tightening Torque3 - 5 Nm
(27 - 44 lb-in)

SSANGYONG MY2002
9M-6 EXTERIOR TRIM
KAA9M090
KAA9M100
C-PILLAR COVER
Removal and Installation Procedure
1. Open the tailgate.
2. Remove the C- pillar cover with the screws.
3. Installation should follow the removal procedure
in the reverse order. 3. Remove the side step from the body.
4. Installation should follow the removal procedure
in the reverse order.
ROOF MOLDING
Removal and Installation Procedure
1. Remove the C-pillar cover. Refer to “C-pillar
Cover” in this section.
2. Remove the roof molding.
3. Installation should follow the removal procedure
in the reverse order.
SIDE STEP
Removal and Installation Procedure
1. Remove the Mud guard. Refer to “Mud Guard” in
this section.
2. Remove the side step mounting bolts.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
KAA9M080
Tightening Torque 15 Nm(11 lb-ft)