1997 SSANGYONG KORANDO parking brake

REAR BRAKES 4E-23
SSANGYONG MY2002
2. Pull out the lever pin (arrow) and Disconnect the
the parking brake lever and the adjuster lever.
3. Installation should follow the removal procedure
in the reverse order.
YAD4C500
PARKING BRAKE LEVER
1. Disconnect the parking brake lever and the
adjuster lever from the lining.
YAD4C490

SECTION 4G
PARKING BRAKE
TABLE OF CONTENTS
Description and Operation..................................4G-2
Brake Caliper......................................................4G-2
Component Locator.............................................4G-3
Repair Instructions...............................................4G-4
On-Vehicle Service................................................4G-4Parking Brake Adjustment - Rear Disc Brakes.....4G-4
Parking Brake Lever............................................4G-5
Parking Brake Cable...........................................4G-6
Specifications......................................................4G-7
Fastener Tightening Specifications......................4G-7

SSANGYONG MY2002
4G-2 PARKING BRAKE
DESCRIPTION AND OPERATION
BRAKE CALIPER
This braking system uses a BRAKE warning light lo-
cated in the instrument panel cluster.
The following conditions will activate the BRAKE lamp:
•The parking brake is applied when the ignition is
ON. The lamp will turn off when the parking brake
is released.
The fluid level is below the minimum mark in the
master cylinder reservoir. The lamp will turn off when
the fluid level is above the minimum.
As a test of the lamp circuit, the BRAKE lamp will
glow dimly when the ignition is ON, even if the
parking brake is off and fluid level is above the
minimum. The lamp will turn off when the engine is
started. When the brake is firmly applied, the parking
brake should hold the vehicle with ample pedal
travel remaining.
Check for frayed cables, rust, etc. or any condition
that may inhibit present (or future) free movement of
the parking brake lever assembly.

PARKING BRAKE 4G-3
SSANGYONG MY2002
KAA4G010
COMPONENT LOCATOR
1 Parking Brake Lever
2 Parking Brake Lever Mounting Bolt
3 Front Parking Brake Cable
4 Equalizer5 Adjuster Nut
6 Rear Parking Brake Cable Securing Bolt
7 Rear Parking Brake Cable
8 Rear Disc Brake Rotor

SSANGYONG MY2002
4G-4 PARKING BRAKE
KAA4G020
KAA4G030
6. Inspect and replace any parts of doubtful strength
or quality because of discoloration from heat or
stress.
Notice:
In the vehicle cabin, pull on the parking brake
handle and stop after hearing two clicks.
Turn the rear wheel by hand until the wheel
begins to drag.
Release the parking brake.
Turn the rear wheel by hand to check drag and
readjust the cable, if necessary.
Repeat the process for the other rear wheel and
lower vehicle.
ON-VEHICLE SERVICE
PARKING BRAKE ADJUSTMENT -
REAR DISC BRAKES
Adjustment Procedure
1. Release the parking brake.
2. Raise and suitably support the vehicle.
3. Remove the rear wheels. Refer to Section 2E, Tires
and Wheels.
4. Remove the rear caliper and rotor assemblies. Refer
to Section 4E, Rear Disc Brakes.
5. Disconnect the rear parking brake cable from the
backplate operating lever on each side of the
vehicle.
REPAIR INSTRUCTIONS

PARKING BRAKE 4G-5
SSANGYONG MY2002
KAA4G040
KAA4G050
KAA4G060
KAA4G070
PARKING BRAKE LEVER
Removal and Installation Procedure
1. Release the parking brake.
2. Raise and suitably support the vehicle.
3. Measure the thread length from the end of the pull
rod to the hex nut.
5. Lower the vehicle.
6. Remove the parking brake/gearshift console hood.
Refer to Section 9G, Interior Trim.
7. Remove the parking brake lever mounting bolts and
washers which secure the complete parking brake
lever assembly to the underbody.
Installation Notice
8. Disconnect the parking brake switch and remove
the clip. If necessary, remove the parking brake
switch attached to the parking brake lever
assembly by a small screw, and remove the switch.
9. Remove the parking brake lever assembly.
Notice:
The parking brake switch should be replaced if
the BRAKE warning light in the instrument panel
cluster did not glow when the parking brake was
applied with the ignition switch ON.
Tightening Torque 18 Nm (13 lb-ft) 4. Remove the parking brake cable ends from the
equalizer and remove the boot.

SSANGYONG MY2002
4G-6 PARKING BRAKE
KAA4G020
KAA4G080
KAA4G050
PARKING BRAKE CABLE
Removal and Installation Procedure
1. Release the parking brake.
2. Raise and suitably support the vehicle.
3. Remove the clip that holds the cable into the rear
knuckle assembly.
6. Remove the parking brake cable ends from the
equalizer.
Tightening Torque 9 Nm (80 lb-in) 5. Remove the bolts securing the parking brake cable
to a holding bracket attached to the trailing link
brackets on both the driver and passenger sides
of the vehicle.
Installation Notice

PARKING BRAKE 4G-7
SSANGYONG MY2002
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
13
- Parking Brake Lever Mounting Bolts
Rear Parking Brake Cable Securing BoltsN•m Application
Lb-InLb-Ft
18
9-
80