1997 SSANGYONG KORANDO wiring

SSANGYONG MY2002
9A-20 BODY WIRING SYSTEM
W/H ENGINE CONTROL (GASOLINE)
6 Crankshaft position sensor
7 Oil pressure switch
8 Knock sensor 2
9 Air flow sensor
10 Ignition coil 3
11 Ignition coil 2
12 Ignition coil 1
13 Injector 6
14 Injector 5
15 Injector 416 Injector 3
17 Injector 2
18 Injector 1
19 Camshaft actuator
20 Camshaft position sensor
21 Engine coolant temperature sensor (Gauge)
22 Engine temperature sensor
23 Throttle motor & sensor
24 Knock sensor 1
25 Intake manifold resonance flap
KAA9A150

BODY WIRING SYSTEM 9A-21
SSANGYONG MY2002
W/H PRE - HEATING (DIESEL)
1 Preheating time control relay
3 Glow plug 1
4 Glow plug 2
5 Glow plug 36 Glow plug 4
7 Glow plug 5 (662 LA only)
8 Engine coolant temperature sensor (Gauge)
KAA9A160

SSANGYONG MY2002
9A-22 BODY WIRING SYSTEM
W/H TRANSMISSION
Automatic Transmission
3 Transmission
4 T/M Lever
5 Inhibitor switch
6 Micro switch (Diesel E/G)7 Throttle position sensor (Diesel E/G)
8 Engine oil pressure switch
9 Engine speed sensor (Diesel E/G)
YAD9B350

BODY WIRING SYSTEM 9A-23
SSANGYONG MY2002
Manual Transmission
1 C302
2 Back up switch
3 Micro switch4 Engine oil pressure switch
5 Engine speed sensor
YAD9B350

SECTION 9C
HORNS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Description and Operation.................................. 9C-2
Horns ................................................................. 9C-2
Components Locator ........................................... 9C-3
Lighting System................................................. 9C-3Repair Instructions............................................... 9C-4
On-Vehice Service Unit Repair............................... 9C-4
Dual Horns......................................................... 9C-4
Schematic and Routing Diagram....................... 9C-5
Horn Wiring System............................................ 9C-5

HORNS 9C-5
SSANGYONG MY2002
SCHEMATIC AND ROUTING DIAGRAMS
HORN WIRING SYSTEM
KAA9C030

WIPER, WASHER SYSTEMS 9D-9
SSANGYONG MY2002
SCHEMATIC AND ROUTING DIAGRAMS
WINDSHIELD WIRING SYSTEM
KAA9D150

INSTRUMENTATION, DRIVER INFORMATION 9E-7
SSANGYONG MY2002
FUEL GAUGE
Fuel Gauge Inoperative
Step
1
2
3
4
5
6
7
8Action
Turn the ignition ON.
Does the fuel gauge always indicate a full fuel tank
with the ignition ON?
Disconnect the fuel tank sending unit.
Does the fuel gauge change to empty?
Replace the fuel tank sending unit.
Is the repair complete?
Check the wiring harness for a short to ground
between the fuel tank sending unit and the fuel
gauge.
Is there a short to ground?
Repair the short to ground.
Is the repair complete?
Replace the fuel gauge.
Is the repair complete?
1. Disconnect the fuel tank sending unit electrical
connector.
2. Turn the Ignition ON.
3. Check the voltage at the fuel tank sending unit
connector C303 terminal 1.
Does the boltmeter indicate the specified value?
Repair the open circuit between the fuel gauge and
the fuel tank sending unit.
Is the repair complete?Yes
Go to Step 2
Go to Step 3
System OK
Go to Step 5
System OK
System OK
Go to Step 9
System OKNo
Go to Step 7
Go to Step 4
-
Go to Step 6
-
-
-
- Value(s)
-
-
-
-
-
-
11 - 14 v
-
Speedometer Is Inoperative (Cont’d)
Step
8
9
10
11
12Action
Use an ohmmeter to check the resistance between
ground and instrument cluster connector terminal B3.
Does the ohmmeter indicate the specified value?
Repair the open circuit between ground and instru-
ment cluster connector terminal B3.
Is the repair complete?
Use an ohmmeter to check continuity of the DK GRN/
WHT wire between the vehicle speed sensor terminal
1 and instrument cluster connector terminal C10.
Does the ohmmeter indicate the specified value?
Repair the open circuit between the vehicle speed
sensor and the instrument cluster.
Is the repair complete?
Replace the speedometer.
Is the repair complete?Yes
Go to Step 10
System OK
Go to Step 12
System OK
System OKNo
Go to Step 9
-
Go to Step 11
-
- Value(s)
0 Ω
-
0 Ω
-
-