1997 SSANGYONG KORANDO torque

1D2 -- 10 M161 ENGINE COOLING
D AEW OO M Y_2000
Tools Required
124589152100 Tester
Removal & Installation Procedure
1. Drain the coolant.
2. Disconnect the coolant hoses (8, 9, 10).
3. Take off the drive belt.
4. Unscrew the four bolts (6) from water pump pulley
and remove the pulley (7).
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Notice:Hold the pulley with fan clutch holder 603 589
00 40 00 while removing the pulley.
5. Unscrew the bolts (1, 2, 3, 4) from water pump hous-
ing (5) and remove the water pump.
Installation Notice
Tightening
(1,2,3)9--11NSm
(80 -- 97 lb-in)
Tightening
Torque(4)22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
6. Clean the sealing surface.
7. Replace the gasket with new one.
Notice:Apply the sealant when the sealing surface of
water pump housing and coolant mounting area is clean.
8. Installation should follow the removal procedure in
the reverse order.
9. Check for leaks by starting the engine.

M161 ENGINE COOLING 1D2 -- 11
D AEW OO M Y_2000
THERMOSTAT
1 Bolt (M6 X 25, 3 pieces)
9--11 NSm (80-- 97 lb-in) .....................
2 Thermostat Cover
3 De-- aeration Hose4 Coolant Outlet Hose
5 Thermostat
6O--ring
Removal & Installation Procedure
1. Drain the coolant from the radiator.
2. Loosen the hose mounting clip and remove the cool-
ant hose (3, 4).
3. Unscrew the three bolts (1) and remove the thermo-
stat cover assembly from thermostat housing.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Do not separate the thermostat cover and thermo-
stat.
4. Replace the O -- ring if necessary.
5. Check the leakage in the cooling system.

M161 ENGINE COOLING 1D2 -- 13
D AEW OO M Y_2000
Removal & Installation Procedure
1. Drain the coolant.
2. Remove the de-- aeration hose (4), coolant outlet
hose (5) and coolant bypass hose (6).
3. Disconnect the coolant temperature sensor connec-
tor.
4. Unscrew the bolt (1c) and pry off the tensioning de-
vice shock absorber (7).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
5. Unscrow the bolts (1a, 1b) and remove the engine
hanger bracket and thermostat housing.
Installation Notice
Tightening
(1a)9--11NSm
(80 -- 97 lb-in)
Tightening
Torque(1b)22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
6. Replace the O -- ring with new one.
7. Installation should follow the removal procedure in
the reverse order.
8. Check for leaks in cooling system.

1D2 -- 14 M161 ENGINE COOLING
D AEW OO M Y_2000
FAN SHROUD
Removal & Installation Procedure
1. Unscrew two bolts from cooling fan shroud and re-
move the shroud.
Installation Notice
Tightening Torque
3--7NSm (27 -- 62 lb-in)
2. Installation should follow the removal procedure in
the reverse order.

1D2 -- 16 M161 ENGINE COOLING
D AEW OO M Y_2000
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermo connector from the ra-
diator.
3. Remove the each coolant hoses.
4. Remove the automatic transmission fluid cooler
pipes from radiator.
Installation Notice
Tightening Torque
20 NSm (15 lb-ft)
5. Remove all the bolts (7) from the radiator bracket (9)
and remove the bracket (9) and insulator (8).
Installation Notice
Tightening Torque
3--7NSm (27 -- 62 lb-in)
6. Remove the radiator (10).
7. Check the radiator pin for crack, damage, leakage
and bending and replace it if necessary.
8. Installation is reverse order of removal.
9. Check for leakage in the cooling system.

M161 ENGINE ELECTRICAL 1E 2 -- 3
D AEW OO M Y_2000
MAINTENANCE AND REPAIR
ON-VEHICE SERVICE
GENERATOR
Preceding Work : Removal of the drivebelt
Removal & Installation Procedure
1. Disconnect the negative battery terminal.
2. Unscrew the nut and disconnect the terminal (1).
Installation Notice
Tightening Torque
14 -- 18 NSm (10 -- 13 lb-ft)
3. Unscrew the nut and disconnect the terminal (2).
Installation Notice
Tightening Torque
4--5NSm (35 -- 44 lb-in)
1 Terminal (B+)
2 Terminal (D+)
4. Unscrew the generator mounting bolt (3).
Installation Notice
Tightening Torque
25 NSm (18 lb-ft)
5. Remove the generator.
6. Installation should follow the removal procedure in
the reverse order.
3 Generator Mounting Bolt
4 Generator

1E 2 -- 4 M161 ENGINE ELECTRICAL
D AEW OO M Y_2000
STARTING MOTOR
Removal & Installation Procedure
1. Disconnect the ground cable.
2. Unscrew the nut and disconnect the battery cable (1).
Installation Notice
Tightening Torque
12 -- 15 NSm (9 -- 11 lb-ft)
3. Unscrew the nut and disconnect the engine electric
wire (2).
Installation Notice
Tightening Torque
6--7NSm (53 -- 62 lb-in)
1 Battery Cable
2 Engine Electric Wire
4. Unscrew the mounting bolts (3) of starting motor.
Installation Notice
Tightening Torque
35 -- 48 NSm (26 -- 35 lb-ft)
5. Remove the starting motor.
6. Installation should follow the removal procedure in
the reverse order.
3 Fixing Bolt
4StartingMotor

M161 ENGINE ELECTRICAL 1E 2 -- 7
D AEW OO M Y_2000
Replacement Procedure
1. Unscrew the three screws(1) and remove the spark
plug cable cover.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
2. Disconnect the cable from ignition coil and spark
plug.
3. Unscrew two bolts(M6 X 25) from each ignition coil
and remove the ignition coil(arrow).
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
4. Remove the spark plug .
Installation Notice
Tightening Torque
20 -- 30 NSm (15 -- 22 lb-ft)
Clearance0.8+0.1mm
Notice:
DTighten the spark plug with specified torque.
DInstall the ignition coil to number 2 and 4 cylinder, and
connect the cable to number 1, 4 and 2, 3 cylinder.
-- T1/1 : cylinder 1 and 4
-- T1/2 : cylinder 2 and 3