11A-2
ENGINE <4G6>
CONTENTS11109000399
GENERAL INFORMATION 3. . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 3. . . . . . . . . . . . . . . . .
SEALANT 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 5. . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 7. . . . . . . . . . . . . . . . . . . . .
Drive Belt Tension Check and Adjustment 7. . . . .
Ignition Timing Check and Adjustment 10. . . . . . .
Idle Speed Check 11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mixture Check 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Compression Pressure Check 12. . . . . . . . . . . . . . . .
Manifold Vacuum Check 13. . . . . . . . . . . . . . . . . . . . . Lash Adjuster Check 14. . . . . . . . . . . . . . . . . . . . . . . .
CAMSHAFT OIL SEAL 16. . . . . . . . . . . . . . . . . . . .
OIL PAN, OIL SCREEN 19. . . . . . . . . . . . . . . . . . . .
CYLINDER HEAD GASKET 21. . . . . . . . . . . . . . . .
TIMING BELT, TIMING BELT B 26. . . . . . . . . . . .
CRANKSHAFT FRONT OIL SEAL 32. . . . . . . . . .
CRANKSHAFT REAR OIL SEAL 35. . . . . . . . . . .
ENGINE ASSEMBLY 37. . . . . . . . . . . . . . . . . . . . . .
ENGINE <4G6> ± General Information/Service Specifications11A-3
GENERAL INFORMATION11100010322
Items4G634G64
Total displacement m1,9972,351
Bore y Stroke mm85.0 x 88.086.5 x 100.0
Compression ratio9.59.5
Combustion chamberPentroof typePentroof type
Camshaft arrangementSOHCSOHC
Number of valve
Intake88
Number of valve
Exhaust88
Intake
OpeningBTDC 11BTDC 18
Valve timing
Intake
ClosingABDC 53ABDC 58
Valve timing
Exhaust
OpeningBBDC 63BBDC 58
Exhaust
ClosingATDC 21ATDC 18
Fuel system
Electronic control
multipoint fuel
injectionElectronic control
multipoint fuel
injection
Rocker armRoller typeRoller type
Auto-lash adjusterEquippedEquipped
SERVICE SPECIFICATIONS11100030342
ItemsStandard valueLimit
Alternator drive
belt
Tension NWhen checked294 ± 490±
belt
tension
When a used belt is installed343 ± 441±
When a new belt is installed490 ± 686±
Deflection
(Reference
When checked7.0 ± 9.0±
(Reference
value) mmWhen a used belt is installed7.5 ± 8.5±
When a new belt is installed5.5 ± 7.5±
Power steering
oilpumpdrive
Tension NWhen checked294 ± 490±
oil um drive
belt tensionWhen a used belt is installed343 ± 441±
When a new belt is installed490 ± 686±
Deflection
(Reference
When checked5.5 ± 7.5±
(Reference
value) mmWhen a used belt is installed6.0 ± 7.0±
When a new belt is installed4.0 ± 6.0±
ENGINE <4G6> ± Service Specifications11A-4
ItemsLimit Standard value
A/C compres-
sor drive belt
Tension NWhen checked355 ± 445±
sor drive belt
tensionWhen a used belt is installed355 ± 445±
When a new belt is installed530 ± 620±
Deflection
(Reference
When checked6.0 ± 7.0±
(Reference
value) mmWhen a used belt is installed6.0 ± 7.0±
When a new belt is installed4.5 ± 5.5±
Basic ignition timing5 BTDC+2±
Idle speed r/min750+100±
CO contents %0.5 or less±
HC contents ppm100 or less±
Compression pressure
(250±400 r/min) kPa
4G631,270min. 960
(250±400 r/min) kPa
4G641,320min. 1,000
Compression pressure difference of all cylinder kPa±max. 100
Intake manifold vacuum kPamin. 60±
Cylinder head bolt shank length mm±99.4
Auto-tensioner push rod movement mmWithin 1.0±
Timing belt tension torque Nm (Reference value)3.5±
Auto tensioner rod protrusion mm2.5 ± 3.0±
ENGINE <4D5> ± Service Specifications/Sealants11B-3
SERVICE SPECIFICATIONS11100030359
ItemsStandard valueLimit
Alternator drive belt
tension (for each
Tension NWhen checked245 ± 441±
tension (for each
belt)When a used belt is installed294 ± 392±)
When a new belt is installed392 ± 588±
Deflection
(Reference
When checked12.0 ± 17.0±
(Reference
value) mmWhen a used belt is installed13.0 ± 16.0±)
When a new belt is installed10.0 ± 13.0±
Power steering oil
pump drive belt ten
Tension NWhen checked294 ± 490±
pump drive belt ten-
sionWhen a used belt is installed343 ± 441±
When a new belt is installed490 ± 686±
Deflection
(Reference
When checked8.0 ± 12.0±
(Reference
value) mmWhen a used belt is installed9.0 ± 11.5±)
When a new belt is installed6.0 ± 8.0±
A/C compressor
drive
Tension NWhen checked320 ± 400±
drive
belt tensionWhen a used belt is installed320 ± 400±
When a new belt is installed480 ± 560±
Deflection
(Reference
When checked6.0 ± 7.0±
(Reference
value) mmWhen a used belt is installed6.0 ± 7.0±)
When a new belt is installed4.5 ± 5.5±
Valve clearance (at hot) mm0.25±
Injection timing (Value indicated on dial gauge mm)9 ATDC (1 + 0.03)±
Idle speed r/min750 + 100±
Idle up engine speed for ABS r/min1,900 + 100±
Compression pressure kPa3,040Min. 2,200
Compression pressure difference of all cylinder (at engine speed of 280
r/min) kPa±Max. 300
Timing belt tension mm4 ± 5±
Timing belt B tension mm4 ± 5±
SEALANTS11100050270
ItemsSpecified sealantRemarks
Oil panMITSUBISHI GENUINE PART
MD970389 or equivalentSemi-drying sealant
Semi-circular packing and rocker
cover seal, and cylinder head seal3M ATD Part No. 8660 or equivalent
ENGINE LUBRICATION ± General Information12-2
GENERAL INFORMATION12100010053
The lubrication method is a fully force-fed, full-flow
filtration type.The corrugate fin type of engine oil cooler have
been adopted, and installed forward of the radiator.
<4D56>
Items4G634G644D56
Oil pump typeInvolute gear typeInvolute gear typeTrochoid type
Drive methodTiming beltTiming beltCrankshaft
ENGINE OILS
Health Warning
Prolonged and repeated contact with mineral oil
will result in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
In addition, used engine oil contains potentiallyharmful contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities must be provided.
Recommended Precautions
The most effective precaution is to adapt working
practices which prevent, as far as practicable, the
risk of skin contact with mineral oils, for example
by using enclosed systems for handling used engine
oil and by degreasing components, where
practicable, before handling them.
Other precautions:
Avoid prolonged and repeated contact with oils,
particularly used engine oils.
Wear protective clothing, including impervious
gloves where practicable.
Avoid contaminating clothes, particularly
underpants, with oil.
Do not put oily rags in pockets, the use of
overalls without pockets will avoid this.
Do not wear heavily soiled clothing and
oil-impregnated foot-wear. Overalls must be
cleaned regularly and kept separate from
personal clothing.Where there is a risk of eye contact, eye
protection should be worn, for example,
chemical goggles or face shields; in addition
an eye wash facility should be provided.
Obtain First Aid treatment immediately for open
cuts and wounds.
Wash regularly with soap and water to ensure
all oil is removed, especially before meals (skin
cleansers and nail brushes will help). After
cleaning, the application of preparations
containing lanolin to replace the natural skin
oils is advised.
Do not use petrol, kerosine, diesel fuel, gas
oil, thinners or solvents for cleaning skin.
Use barrier creams, applying them before each
work period, to help the removal of oil from
the skin after work.
If skin disorders develop, obtain medical advice
without delay.
MPI ± Troubleshooting13A-47
INSPECTION PROCEDURE 34
MUT-II: Inspection of no initial combustion
MUT-II Data list
16 Voltage of engine-ECU power source (Refer to P.13A-57.)NGCheck the power supply and ignition switch-IG system.
(Refer to P.13A-39, INSPECTION PROCEDURE 23.)
OK
Does the camshaft rotate at the engine cranking?
(When oil filler cap is removed.)NoCheck timing belt for breakage.
Ye s
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
MUT-II Data list
22 Crank angle sensor
OK:Cranking speed is displayed.NoCheck the crank angle sensor system.
(Refer to P.13A-15, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 22.)
OK
MUT-II Actuator test
07 Fuel pump (Refer to P.13A-62.)NGCheck the fuel pump system.
(Refer to P.13A-40, INSPECTION PROCEDURE 24.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13A-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13A-14, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
INSPECTION PROCEDURE 35
Ignition system: Inspection of no initial combustion.
Does the engine tachometer display the cranking speed?
Set the tachometer of primary voltage detection type.NGCheck ignition circuit system.
(Refer to P.13A-44, INSPECTION PROCEDURE 30.)
OK
Check the ignition timing when cranking.
OK:Approx. 5BTDCNGCheck that the crank angle sensor is installed properly.