1997 MITSUBISHI TRITON water pump

charging language oil capacity technical data jump start terminals bolt pattern

Page 117 of 1310

MITSUBISHI TRITON 1997 Workshop Manual ENGINE LUBRICATION ± General Information12-2
GENERAL INFORMATION12100010053
The lubrication method is a fully force-fed, full-flow
filtration type.The corrugate fin type of engine oil cooler have
bee

ENGINE LUBRICATION ± General Information12-2
GENERAL INFORMATION12100010053
The lubrication method is a fully force-fed, full-flow
filtration type.The corrugate fin type of engine oil cooler have
been adopted, and installed forward of the radiator.
<4D56>
Items4G634G644D56
Oil pump typeInvolute gear typeInvolute gear typeTrochoid type
Drive methodTiming beltTiming beltCrankshaft
ENGINE OILS
Health Warning
Prolonged and repeated contact with mineral oil
will result in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
In addition, used engine oil contains potentiallyharmful contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities must be provided.
Recommended Precautions
The most effective precaution is to adapt working
practices which prevent, as far as practicable, the
risk of skin contact with mineral oils, for example
by using enclosed systems for handling used engine
oil and by degreasing components, where
practicable, before handling them.
Other precautions:
Avoid prolonged and repeated contact with oils,
particularly used engine oils.
Wear protective clothing, including impervious
gloves where practicable.
Avoid contaminating clothes, particularly
underpants, with oil.
Do not put oily rags in pockets, the use of
overalls without pockets will avoid this.
Do not wear heavily soiled clothing and
oil-impregnated foot-wear. Overalls must be
cleaned regularly and kept separate from
personal clothing.Where there is a risk of eye contact, eye
protection should be worn, for example,
chemical goggles or face shields; in addition
an eye wash facility should be provided.
Obtain First Aid treatment immediately for open
cuts and wounds.
Wash regularly with soap and water to ensure
all oil is removed, especially before meals (skin
cleansers and nail brushes will help). After
cleaning, the application of preparations
containing lanolin to replace the natural skin
oils is advised.
Do not use petrol, kerosine, diesel fuel, gas
oil, thinners or solvents for cleaning skin.
Use barrier creams, applying them before each
work period, to help the removal of oil from
the skin after work.
If skin disorders develop, obtain medical advice
without delay.

Page 149 of 1310

MITSUBISHI TRITON 1997 Workshop Manual MPI ± Troubleshooting13A-26
INSPECTION PROCEDURE 5
No initial combustion (starting impossible)
Probable cause
In cases such as the above, the cause is probably that a spark plug is defective,
or that

Page 156 of 1310

MITSUBISHI TRITON 1997 Workshop Manual MPI ± Troubleshooting13A-33
INSPECTION PROCEDURE 12
When the engine is hot, it stalls at idling. (Die out)
Probable cause
In such cases as the above, the cause is probably that ignition system, air/f

MPI ± Troubleshooting13A-33
INSPECTION PROCEDURE 12
When the engine is hot, it stalls at idling. (Die out)
Probable cause
In such cases as the above, the cause is probably that ignition system, air/fuel mixture,
idle speed control (ISC) or compression pressure is defective.
In addition, if the engine suddenly stalls, the cause may also be a defective connector
contact.Malfunction of the ignition system
Malfunction of air-fuel ratio control system
Malfunction of the ISC system
Drawing air into intake system
Improper connector contact
Were the battery terminals disconnected?Ye sAfter warming-up, let the engine run at idling for 10 minutes.
No
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
Check the ISC servo for operation sound. (Refer to P.13A-90.)NGCheck the ISC servo system.
(Refer to P.13A-45, INSPECTION PROCEDURE 31.)
OK
Check the injector for operation sound.NGCheck the injector system. (Refer to P.13A-19, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Does the engine stall right after the accelerator pedal is released?Ye sClean the throttle valve
area. (Refer to P.13A-78.)Check and adjust the
fixed SAS.
(Refer to P.13A-79.)
No
Does the engine stall easily again?NoWhile carrying out an intermittent malfunction simulation test (Refer
to GROUP 00 ± Points to Note for Intermittent Malfunctions.), check
for sudden changes in the signals shown below.
Crank angle sensor signal
Air flow sensor signal
Injector drive signalPrimary and secondary
ignition signal
Fuel pump drive signal
Engine-ECU power supply
voltage
Ye s
MUT-II: Engine stalling inspection when the engine is warm and
idling. (Refer to P.13A-50, INSPECTION PROCEDURE 39.)
OK
Check the ignition timing.
(Refer to GROUP 11 ± On-vehicle Service.)NGCheck that the distributor is installed properly.
OK
Check the following items.
Check the ignition coil, spark plugs, spark plug cables. (Refer to GROUP 16 ± On-vehicle Service.)
Check if the injectors are clogged.
Check the compression pressure. (Refer to GROUP 11 ± On-vehicle Service.)
Check if foreign materials (water, alcohol, etc.) got into fuel.

Page 241 of 1310

MITSUBISHI TRITON 1997 Workshop Manual ENGINE COOLING ±
General Information/
Service Specifications/Lubricant/Sealants14-2
GENERAL INFORMATION14100010125
The cooling system is designed to keep every part
of the engine at appropriate temp

wiper blades dimensions adblue tire pressure reset engine oil fuel tank removal