1997 MITSUBISHI TRITON change wheel

MPI ± Troubleshooting13A-65
Terminal No.Normal condition Check condition (Engine condition) Check item
35Oxygen sensor heaterEngine: Idling after warming up0±3V
Engine r/min: 5,000r/min.System voltage
36Engine warning lampIgnition switch: OFF
ON0 ± 3V
9 ± 13V
(After several seconds have
elapsed)
37Power steering fluid
pressure switchEngine: Idling after
warming upWhen steering
wheel is stationarySystem voltage
When steering
wheel is turned0±3V
38Control relay
(Power supply)
Ignition switch: OFFSystem voltage
(Power su ly)
Ignition switch: ON0±3V
45A/C switchEngine: Idle speedTurn the A/C
switch OFF0±3V
Turn the A/C
switch ON (A/C
compressor is
operating)System voltage
51Ignition switch ± STEngine: Cranking8V or more
52Intake air temperature
sensorIgnition switch:
ONWhen intake air
temperature is
0
C3.2 ± 3.8V
When intake air
temperature is
20
C2.3 ± 2.9V
When intake air
temperature is
40
C1.5 ± 2.1V
When intake air
temperature is
80
C0.4 ± 1.0V
56Oxygen sensorEngine: Running at 2,500 r/min after
warmed up (Check using a digital type
voltmeter)0
0.8V
(Changes repeatedly)
60Backup power supplyIgnition switch: OFFSystem voltage
61Sensor impressed
voltageIgnition switch: ON4.5 ± 5.5V
62Ignition switch ± IGIgnition switch: ONSystem voltage

MANUAL TRANSMISSION ± 4WD Indicator-ECU22-16
Terminal No.Inspection itemInspection condition
1: Ignition switchInspection condition
2: Transfer lever positionTerminal voltage
1Free wheel engage
switch
ON2HSystem voltage
switch
4H*10 V
24WD detection
switch
ON2HSystem voltage
switch
4H, 4L0 V
3Ignition switch (IG1)OFF±0 V
ON±System voltage
5Free wheel differen-
tial indicator lamp
ON2HSystem voltage
tial indicator lam
4H*10 V
6HI/LOW detection
switchONShifting from 4H to 4L
or vice versaSystem voltage
2H, 4H, 4L0 V
7Free wheel clutch
changeover solenoid
ON4H, 4L0 V
changeover solenoid
valve2H*2System voltage
104WD Indicator lampON2H0 V
4H, 4LSystem voltage
NOTE
*1: When vehicle has been moved once.
*2: Shift the lever from 4H to 2H, and then turn the ignition switch to OFF and then back to ON.

ABS <2WD> ± Troubleshooting35B-14
INSPECTION CHART FOR TROUBLE SYMPTOMS35201140142
Get an understanding of the trouble symptoms and check according to the inspection procedure chart.
Trouble symptomsInspection
procedure No.Reference
page
Communication with MUT-II
is notpossible
Communication with all systems is not possible.135B-15
is not ossible.
Communication with ABS only is not possible.235B-15
When the ignition key is turned to ªONº (engine stopped), the ABS warning lamp does
not illuminate.335B-16
After the engine starts, the ABS warning lamp remains illuminated.435B-16
When the ignition key is turned to ªSTARTº, the ABS warning lamp does not illuminate.535B-17
After the ignition key is turned to ªONº, the ABS warning lamp blinks twice, and when
turned to ªSTARTº, it illuminates. When returned to ªONº, the lamp flashes once, and
then switches off.635B-17
Faulty ABS operationUnequal braking power on both sides735B-18
Insufficient braking power
ABS operates under normal braking conditions
ABS operates before vehicle stops under normal
braking conditions
Large brake pedal vibration (Caution 2.)±±
Caution
1. If steering movements are made when driving at high speed, or when driving on road surfaces
with low frictional resistance, or when passing over bumps, the ABS may operate even though
sudden braking is not being applied. Because of this, when getting information from the customer,
check if the problem occurred while driving under such conditions as these.
2. During ABS operation, the brake pedal may vibrate or may not be able to be depressed. Such
phenomena are due to intermittent changes in hydraulic pressure inside the brake line to prevent
the wheels from locking and is not an abnormality.