1997 LINCOLN MARK VIII position

235
NOTE:If the vehicle has been operated for an
extended period at high speeds or in city traffic
during hot weather, or pulling a trailer, the vehicle
should be turned off for about 30 minutes to allow
the fluid to cool before checking.Checking the Automatic Transmission
FluidWith the vehicle on a level surface and the brake
fully applied, start the engine and move the gear
shift selector through all of the gears allowing
sufficient time for each position to engage. Securely
latch the gear shift selector in the P (Park) position.
Fully set the parking brake and leave the engine
running.
NOTE:Your vehicle should not be driven if the
fluid level does not appear on the dipstick tip and
outside temperatures are above50ÊF(10ÊC).
Wipe off the dipstick cap and pull the dipstick out.
Wipe the indicator end clean. Put the dipstick back
into the filler tube and make sure it is fully seated.Pull the dipstick out and read the fluid level.
When checking fluid at normal operating
temperatures150ÊF-170ÊF (66ÊC-77ÊC), thefluid
level should be within the ªHOTº notched area on
the dipstick. When the vehicle has not been driven,
and outside temperatures are above68ÊF(20ÊC),
the fluid levels should be between the ªHOTº
notch and the tip end of the dipstick.
Adding Automatic Transmission FluidBefore adding any fluid, be sure that the correct
type will be used. Use only MerconHFluid, as
shown on handle.
Add fluid in 1/2 pint (250ML) increments through
the filler tube to bring the level to the correct area
on the dipstick. DO NOT OVERFILL. If the level is
above the top hole on the dipstick, excess fluid
should be removed by a qualified technician.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

255
Headlamp bulb removalRemoving the high beam headlamp bulb1. Make sure that the headlamp switch is in the
OFF position.
2. Lift the hood, remove the sight shield above
the headlamp and find the bulb in the
headlamp socket.3. Remove the high beam dust cap by rotating
counterclockwise 1/4 turn. Pull back to
exposes wiring and connector.
4. Remove the bulb connector by pulling rearward
to free it from the lamp assembly.
5. Remove the electrical connector by pulling off
the bulb base.
Installing the high beam headlamp bulb1. Push the electrical connector into the rear of
the plastic base of the bulb until it snaps,
locking it into position.
2. Insert the glass envelope of the bulb into the
lamp assembly socket while aligning the locking
tabs.
3. Rotate the bulb 1/4 turn to lock.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

2564. Replace the high beam dust cap by aligning
tabs and rotating clockwise 1/4 turn.
5. Replace the sight shield.Aiming HeadlampsYour vehicle is equipped with a Vehicle Headlamp
Aim Device (VHAD) on each headlamp body. Each
headlamp may be properly aimed in the horizontal
direction (left/right) and the vertical position
(up/down).
NOTE:A non-zero bubble reading does not
necessarily indicate out-of-aim headlamps. If your
vehicle is not positioned on a level surface, the
slope will be included in the level indicator.
Therefore, vertical headlamp adjustment should be
performed only when beam direction appears to be
incorrect or a level surface can be verified.Tools required: One 6mm socket and ratchet.
The Horizontal aim must be adjusted first.
NOTE:The following procedure assumes that the
vehicle's front structure is in factory alignment
condition. If the vehicle has been in an accident
requiring the front end of the vehicle to be
repaired, the horizontal indicator should be
recalibrated by the servicing facility.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

257
Before adjusting your headlamps, you must make
sure that the air suspension has been adjusted to
the proper ride height. In order to do this:
1. Position the vehicle on a level surface.
2. Make sure the air suspension switch in the
luggage compartment is in the ON position.
3. Turn the ignition key to the ON position.
4. Open and close the driver's door to allow the
air suspension to fully level.
File:11fnmc8.ex
Update:Thu Jun 20 14:28:32 1996

277
Vehicle Identification Number (VIN/Serial
Number)Mediation/Arbitration Program
(Canada Only)In those cases where you continue to feel that the
efforts by Ford and the dealer to resolve a
factory-related vehicle service concern have been
unsatisfactory, Ford of Canada participates in an
impartial third party mediation/arbitration program
administered by the Canadian Motor Vehicle
Arbitration Plan (CAMVAP).The CAMVAP program is a straight-forward and
relatively speedy alternative to resolve a
disagreement when all other efforts to produce a
settlement have failed. This procedure is without
cost to you and is designed to eliminate the need
for lengthy and expensive legal proceedings.
In the CAMVAP program, impartial third-party
Arbitrators conduct hearings at mutually convenient
times and places in an informal environment. These
impartial Arbitrators review the positions of the
parties, make decisions and, where appropriate,
render awards to resolve disputes. CAMVAP
decisions are fast, fair and final as the arbitrator's
award is binding on both you and Ford of Canada.
CAMVAP services are available in all territories and
provinces, except Quebec. For more information,
without charge or obligation, call your CAMVAP
Provincial Administrator directly at 1-800-207-0685.
File:14fnhs8.ex
Update:Wed Jun 19 15:06:24 1996

295
Index
A
ABS warning light (see Anti-lock
brake system)............ 11
Accessory position on the ignition.... 83
Accident damage............ 216
Air bag supplemental restraint system . . . 145
and child safety seats......... 151
description............. 145
driver air bag............ 145
indicator light............ 45
operation.............. 147
passenger air bag........... 145
tone generator............ 149
Air cleaner filter
location............... 220
specifications............ 263Air conditioning, electronic automatic
temperature control system....... 69
Air suspension
air ride switch off, message center . . . 37
description............. 175
Alarm, activating remote personal..... 123
Aluminum wheels........... 242
Antenna, radio (see Electronic
sound system)............ 66
Antifreeze (see Engine coolant)...... 228
Anti-lock brake system (ABS)
description............. 171
see also Brake............ 171
warning light............ 11
Anti-theft lug nuts and key........ 208
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996

303
G
Gas cap (see Fuel cap)......... 243
Gas mileage (see Fuel economy) . . . 25, 248
Gasoline (see Fuel)........... 243
Gauges
engine coolant temperature gauge . . . 17
fuel gauge.............. 19
odometer.............. 16
speedometer............. 16
tachometer............. 17
GAWR (Gross Axle Weight Rating)
calculating............. 183
definition.............. 182
driving with a heavy load....... 182
location............... 182Gearshift
automatic operation.......... 177
locking the gearshift......... 83
positions.............. 177
shifting the gears........... 177
GVWR (Gross Vehicle Weight Rating) . . . 182
calculating.............. 183
definition.............. 182
driving with a heavy load....... 182
location............... 182
H
Hazard flashers............. 89
Headlamps
aiming............... 256
autolamp system........... 80
checking alignment.......... 253
cleaning............... 261
daytime running lights........ 78
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996

304Headlamps (continued)
flashing............... 86
high beam............. 86
replacing bulbs........... 253
turning on and off.......... 79
warning chime............ 15
Head restraints............. 131
Heated seats.............. 135
Heating
electronic automatic temperature
control system........... 69
High beams
indicator light............ 14
operation.............. 86
Hitch................. 186
Hood................. 219
latch location............ 219
lubrication specifications....... 265
release lever............. 219
working under the hood....... 217
Horn................. 90
I
Idle, relearning..........212, 217
Ignition
chime............... 84
positions of the ignition........ 83
removing the key.......... 84
Indicator lights and chimes (see Lights) . . . 7
Infant seats (see Safety seats)....150, 151
Instrument panel............. 7
Interval wipers............. 86
J
Jack.................. 202
operation.............. 203
positioning............. 205
storage............... 202
Jump-starting your vehicle
attaching cables........... 211
disconnecting cables......... 212
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996