1996 TOYOTA TERCEL wheel

CL060-03
Z14164
Flywheel
Clutch Disc
Clutch Cover
Boot Release Fork Release Bearing with Hub X6 CL-14
- CLUTCHCLUTCH UNIT
709 Author
: Date
:
1996 TERCEL (RM440U)
CLUTCH UNIT
COMPONENTS

CL061-01
CL0288Matchmarks
N00413
- CLUTCHCLUTCH UNIT
CL-15
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE TRANSAXLE FROM ENGINE
(See page MX-4)
2. REMOVE CLUTCH COVER AND DISC
(a) Place matchmarks on the flywheel and clutch cover.
(b) Loosen each set bolt one turn at a time until spring tension
is released.
(c) Remove the set bolts, and pull off the clutch cover with the
clutch disc.
NOTICE:
Do not drop the clutch disc.
3. REMOVE RELEASE BEARING AND FORK FROM
TRANSAXLE
Remove the release bearing together with the fork and then
separate them.

CL062-01
CL0239
CL0373
CL0290
Z08001
AB
N00414
CL-16
- CLUTCHCLUTCH UNIT
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT CLUTCH DISC FOR WEAR OR DAMAGE
Using calipers, measure the rivet head depth.
Minimum rivet depth: 0.3 mm (0.012 in.)
If necessary, replace the clutch disc.
2. INSPECT CLUTCH DISC RUNOUT
Using a dial indicator, check the disc runout.
Maximum runout: 0.8 mm (0.031 in.)
If necessary, replace the clutch disc.
3. INSPECT FLYWHEEL RUNOUT
Using a dial indicator, check the flywheel runout.
Maximum runout: 0.1 mm (0.004 in.)
If necessary, replace the flywheel.
4. INSPECT DIAPHRAGM SPRING FOR WEAR
Using calipers, measure the diaphragm spring for depth and
width of wear.
Maximum depth:
A: 0.6 mm (0.024 in.)
Maximum width:
B: 5.0 mm (0.197 in.)
If necessary, replace the clutch cover.
5. INSPECT RELEASE BEARING
Turn the bearing by hand while applying force in the axial direc-
tion.
HINT:
The bearing is permanently lubricated and requires no cleaning
or lubrication.
If necessary, replace the release bearing.

CL063-03
Q06681
Flywheel Side
CL0291
1.4
MatchmarksSST 7 3
6
2.58
Q06392
SST
N00415
CL0653
- CLUTCHCLUTCH UNIT
CL-17
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL CLUTCH DISC AND CLUTCH COVER ON
FLYWHEEL
(a) Insert SST in the clutch disc, and then set them.
SST 09301-00210
(b) Align the matchmark on the clutch cover and flywheel.
(c) Torque the bolts on the clutch cover in the order shown.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
HINT:
Temporarily tighten the No.1 and No.2 bolts.
2. CHECK DIAPHRAGM SPRING TIP ALIGNMENT
Using a dial indicator with roller instrument, check the dia-
phragm spring tip alignment.
Maximum non-alignment: 0.5 mm (0.020 in.)
If alignment is not as specified, using SST, adjust the dia-
phragm spring tip alignment.
SST 09333-00013
3. APPLY MOLYBDENUM DISULPHIDE LITHIUM BASE
GREASE (NLGI NO.2)
(a) Apply release hub grease to these parts:

Release fork and hub contact point

Release fork and push rod contact point

Release fork pivot point
(b) Apply clutch spline grease.
Clutch disc spline
HINT:
Recommended grease part number 08887-01706 (100 g).
4. INSTALL RELEASE BEARING AND FORK TO TRANS-
AXLE
Install the bearing to the release fork, and then install them to
the transaxle.
5. INSTALL TRANSAXLE TO ENGINE
(See page MX-6)

MX07F-04
Q06439
Z1891017 mm Head
Starter Set Bolt
Q06443
Q09187
Filler Plug
Oil Level
0 - 5 mm
Drain Plug MX-4
- MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE BATTERY AND AIR CLEANER CASE AS-
SEMBLY WITH AIR HOSE
2. REMOVE CLUTCH RELEASE CYLINDER AND LINE
CLAMP
(a) Remove the 2 bolts and release cylinder.
(b) Remove the 2 bolts and release cylinder line clamp.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
3. DISCONNECT GROUND CABLE
Remove the 2 bolts and disconnect the 2 ground cables from
the transaxle side and engine left mounting bracket side.
4. DISCONNECT BACK-UP LIGHT SWITCH CONNEC-
TOR
5. DISCONNECT CONTROL CABLE
(a) Remove the 2 clips and washers.
(b) Remove the 2 clips from the cables.
6. REMOVE STARTER SET BOLT
Remove the 2 set bolts of the starter from the transaxle upper
side.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
7. REMOVE TRANSAXLE MOUNTING BOLT
Remove the 3 bolts of transaxle case upper side.
Torque:
17 mm head: 64 N´m (650 kgf´cm, 47 ft´lbf)
8. INSTALL ENGINE SUPPORT FIXTURE
9. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
10. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
11. REMOVE LH AND RH ENGINE UNDER COVERS
12. DRAIN TRANSAXLE OIL
Oil grade: API GL-4 or GL-5
Viscosity: SAE 75W-90
Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
13. REMOVE LH AND RH DRIVE SHAFTS
(See page SA-17)

MX07G-02
MX-6
- MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal.
HINT:
After installation, check and inspect items as follows.

Front wheel alignment (See page SA-4).

Do the road test.

AT8103
Neutral Basic Line
Groove
- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE SYSTEM (A132L)
AX-5
1996 TERCEL (RM440U)
(2) Using an ohmmeter, check continuity between each
terminal shown below when the shift lever is put in
each position.
(h) Adjust the shift control cable.
(1) Remove the engine under cover.
(2) Loosen the nut on the control shaft lever.
(3) Push the control shaft lever fully toward the right
side of the vehicle.
(4) Return the lever 2 notches to the NEUTRAL posi-
tion.
(5) Set the shift lever to the N position.
(6) While holding the lever lightly toward the ºRº posi-
tion side, tighten the swivel nut.
(i) Adjust the park/neutral position switch.
If the engine will start with the shift selector in any position other
than the N or P position, adjustment is required.
(1) Loosen the park/neutral position switch bolts and
set the shift selector to the N position.
(2) Align the groove with neutral basic line.
(3) Hold the switch in the position and tighten the bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(j) Inspect the idle speed.
Idle speed:
750 ± 50 rpm (In the N position and A/C OFF)
3. MEASURE STALL TEST
The object of this test is to check the overall performance of the transaxle and the engine by measuring the
maximum engine speeds in the D and R positions.
NOTICE:
Do the test at normal operating fluid temperature 50 - 80°C (122 - 176 °F).
Do not continuously run this test longer than 5 seconds.
(1) Check the front and rear wheels.
(2) Connect the tachometer to the engine.
(3) Fully apply the parking brake.

- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE SYSTEM (A132L)
AX-7
1996 TERCEL (RM440U)
5. HYDRAULIC TEST
(a) Measure the line pressure.
(1) Warm up the transaxle fluid.
(2) Remove the transaxle case test plug and mount SST (See page AX-25).
SST 09992-00094 (09992-00150, 09992-00270)
NOTICE:
Do the test at normal operating fluid temperature 50 - 80°C (122 - 176 °F).
(3) Fully apply the parking brake and check the 4 wheels.
(4) Start the engine and check the idle speed.
(5) Shift into the D position,step down strongly on the brake pedal with your left foot and while manip-
ulating the accelerator pedal with the right foot, measure the line pressure at the engine speeds
specified in the toble.
(6) In the same manner, do the test in the R position.
Specified line pressure:
D positionIdling
Stall363 - 422 kPa (3.7 - 4.3 kgf/cm2, 53 - 61 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
R position Idling
Stall530 - 706 kPa (5.4 - 7.2 kgf/cm2, 77 - 102 psi)
1,412 - 1,647 kPa (14.4 - 16.8 kgf/cm2, 205 - 239 psi)
(7) If the measured pressures are not up to specified values, recheck the throttle cable adjustment
and retest it (see step 2).
EVALUATION
ProblemPossible cause
If the measured values at all positions are higher.
 Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
If the measured values at all positions are lower.
 Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
 Oil pump defective
If pressure is low in the D position only. D position circuit fluid leakage
 Forward clutch defective
If pressure is low in the R position only.
 R position circuit fluid leakage
 Direct clutch defective
 1st and reverse brake defective
(b) Measure the governor pressure.
(1) Warm up the transaxle fluid.
(2) Remove the transaxle case test plug and mount SST (See page AX-25).
SST 09992-00094 (09992-00230, 09992-00270)
NOTICE:
Do the test at normal operating fluid temperature 50 - 80 °C (122 - 176 °F).
(3) Check the parking brake to see that it is not applied.
(4) Start the engine.
(5) Shift into the D position and measure the governor pressures at the speeds specified in the table.