1996 TOYOTA TERCEL vacuum line

BR0RL-01
F05027
BR5055
R04651
- BRAKEBRAKE BOOSTER ASSEMBLY
BR-17
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE MASTER CYLINDER (See page BR-10)
2. DISCONNECT VACUUM HOSE FROM BRAKE
BOOSTER
3. REMOVE PEDAL RETURN SPRING
4. REMOVE CLIP AND CLEVIS PIN
5. REMOVE BRAKE BOOSTER
(a) Remove the No.1 brake line clamp.
(b) Remove the No.2 brake line clamp.
(c) Remove the 4 nuts and clevis.
(d) Pull out the brake booster and gasket.

BR0RM-04
F03521
SST
Gasket
N00744
SST
BR1728 BR0021
BR-18
- BRAKEBRAKE BOOSTER ASSEMBLY
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL BRAKE BOOSTER
(a) Install the booster and a new gasket.
(b) Install the clevis to the operating rod.
(c) Install and torque the booster installation nuts.
Torque: 14 N´m (145 kgf´cm, 10 ft´lbf)
(d) Insert the clevis pin into the clevis and brake pedal, and
install the clip to the clevis pin.
(e) Install the pedal return spring.
(f) Install the No.1 brake line clamp to the body.
(g) Install the No.2 brake line clamp to the body.
2. ADJUST LENGTH OF BOOSTER PUSH ROD
(a) Install the gasket on the master cylinder.
(b) Set SST on the gasket, and lower the pin until its tip slight-
ly touches the piston.
SST 09737-00010
(c) Turn SST upside down, and set it on the booster.
SST 09737-00010
(d) Measure the clearance between the booster push rod
and pin head (SST).
Clearance: 0 mm (0 in.)
(e) Adjust the booster push rod length until the push rod
slightly touches the pin head.
HINT:
When loosening the push rod nut, depress the brake pedal
enough so that the push rod sticks out.
3. INSTALL MASTER CYLINDER
4. CONNECT VACUUM HOSE TO BRAKE BOOSTER
5. FILL BRAKE RESERVOIR WITH BRAKE FLUID AND
BLEED BRAKE SYSTEM (See page BR-4)
6. CHECK FOR LEAKS

AC1DT-01
N13795
Quick Disconnect
Adapter
Charging
Service ValveHose
N13794
Vacuum Pump
Vacuum Pump Adapter
N13791
Low Pressure
Service Valve
Vacuum Pump Adapter High Pressure
Service ValveManifold
Gauge
Set
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
AC-1 1
1996 TERCEL (RM440U)
EVACUATING
1. CONNECT QUICK DISCONNECT ADAPTER TO
CHARGING HOSES
2. REMOVE CAPS FROM SERVICE VALVES ON RE-
FRIGERANT LINES
3. SET ON MANIFOLD GAUGE SET
(a) Close both hand valves of manifold gauge set.
(b) Connect the quick disconnect adapters to the service
valves.
4. EVACUATE AIR FROM REFRIGERATION SYSTEM
(a) Connect the vacuum pump adapter to the vacuum pump.
(b) Connect the center hose of the manifold gauge set to the
vacuum pump adapter.
(c) Open both the high and low hand valves and run the vacu-
um pump.
(d) After 10 minutes or more, check that the low pressure
gauge indicates 750 mmHg (30 in. Hg) or more.
HINT:
If the reading is 750 mmHg (30 in. Hg) or more, close both hand
valves of manifold gauge set and stop the vacuum pump.
Check the system for leaks and repair if necessary.
(e) Close both the high and low hand valves and stop the vac-
uum pump.
(f) Leave the system in this condition for 5 minutes or more
and check that there is no gauge indicator.