Page 1545 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GF−01
SA0040
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (2WD)
SA−75
1996 TOYOTA T100 (RM449U)
DISPOSAL
1. FULLY EXTEND SHOCK ABSORBER ROD
2. DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole in the cylinder, as shown to remove
the gas inside.
CAUTION:
The discharged gas is harmless, but be careful of chips
which may fly up when drilling.
Page 1546 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GG−01
SA−76
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (2WD)
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−73).
Page 1547 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GH−02
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (4WD)
SA−77
1516 Author: Date:
1996 TOYOTA T100 (RM449U)
FRONT SHOCK ABSORBER (4WD)
COMPONENTS
Page 1548 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GI−01
R04246
SA−78
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (4WD)
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE SHOCK ABSORBER
(a) Remove the nut and washer, and disconnect the shock
absorber lower side from the lower suspension arm.
Torque: 137 N·m (1,400 kgf·cm, 101 ft·lbf)
(b) Hold the shock absorber and remove the nut, retainer,
cushion and shock absorber.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Remove the 2 retainers and cushion from the shock ab-
sorber.
Page 1549 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GJ−01
R04270
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (4WD)
SA−79
1996 TOYOTA T100 (RM449U)
INSPECTION
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber piston rod and check
that there is no abnormal resistance or unusual operation
sound.
If there is any abnormality, replace the shock absorber with a
new one.
NOTICE:
When discarding the shock absorber, see DISPOSAL on
page SA−80.
Page 1550 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GK−01
R04271
SA−80
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (4WD)
1996 TOYOTA T100 (RM449U)
DISPOSAL
1. FULLY EXTEND SHOCK ABSORBER ROD
2. DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole in the cylinder, as shown to remove
the gas inside.
CAUTION:
The discharged gas is harmless, but be careful of chips
which may fly up when drilling.
Page 1551 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GL−01
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER (4WD)
SA−81
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−78).
Page 1552 of 2062
Downloaded from www.Manualslib.com manuals search engine SA0GM−07
SA−82
− SUSPENSION AND AXLEFRONT TORSION BAR SPRING (2WD)
1521 Author: Date:
1996 TOYOTA T100 (RM449U)
FRONT TORSION BAR SPRING (2WD)
COMPONENTS
