1996 TOYOTA RAV4 fuel filter

SF0QI−03
S01903
S01939
(1)
(2)
S01827
S01949
Disconnect
Spacer
− SFIINJECTOR
SF−19
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE AIR CLEANER ASSEMBLY (See page
ST−4)
2. REMOVE CYLINDER HEAD COVER (See page
EM−33)
3. DISCONNECT THROTTLE BODY FROM INTAKE MAN-
IFOLD (See page SF−30)
4. REMOVE DISTORIBUTOR (See page IG−9)
5. DISCONNECT ENGINE WIRE FROM INTAKE MAN-
IFOLD
(a) Disconnect the 4 injector connectors.
(b) Disconnect the 2 clamps of the engine wire from the wire
brackets on intake manifold.
(c) Remove the bolt, and disconnect the engine wire protec-
tor from the RH side of the intake manifold.
(d) Disconnect the clamp of the engine wire from the wire
clamp.
6. REMOVE EGR VALVE AND PIPE
(a) Disconnect these hoses from the EGR valve:
(1) Vacuum hose from port E of VSV
(2) EGR hose from vacuum modulator
(b) Loosen the cylinder head side of the EGR pipe union nut.
(c) Remove the 2 nuts, the EGR valve, pipe assembly and
gasket.
7. DISCONNECT ENGINE COMPORTMENT R/B NO.2
8. REMOVE FUEL INLET HOSE AND DELIVERY PIPE
(a) Remove the union bolt and 2 gaskets, and disconnect the
fuel inlet hose from the fuel filter outlet.
CAUTION:
Put a shop towel under the fuel filter. Slowly loosen the
union bolt.
(b) Disconnect the air hose for the air assist system from the
intake manifold port, and remove the air hose.
(c) Loosen the 2 bolts holding the delivery pipe to the cylinder
head.
(d) Disconnect the delivery pipe from the 4 injectors, and re-
move the delivery pipe and fuel inlet hose assembly.
9. REMOVE INJECTORS AND SPACERS
(a) Remove the 4 injectors and 2 spacers from the cylinder
head.
NOTICE:
Be careful not to drop the injectors and spacers.

SF0QJ−04
S01900
Union Bolt
SST (Union)SST
(Hose)SST
(Clamp)
Injector Fuel Filter
(On−Vehicle)SST
(Union)
S01833
Union Bolt
SST
(Hose)
Fuel FilterSST
(Union)
Gasket
P25498
SST
(Hose)
SST
(Clamp) SST
(Union)
O−Ring
Vinyl
Tube
S01354
TOYOTA
Hand−Held Tester
− SFIINJECTOR
SF−21
1996 RAV4 (RM447U)
INSPECTION
1. INSPECT INJECTOR INJECTION
CAUTION:
Keep injector clear of sparks during the test.
(a) Connect SST (union and hose) to the fuel filter outlet with
the 2 gaskets and union bolt.
SST 09268−41046 (90405−09015)
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
HINT:
Use the vehicle’s fuel filter.
(b) Install the grommet and O−ring to the injector.
(c) Connect SST (union and hose) to the injector, and hold
the injector and union with SST (clamp).
SST 09268−41046
(d) Put the injector into a graduated cylinder.
HINT:
Install a suitable vinyl hose onto the injector to prevent gasoline
from splashing out.
(e) Connect the TOYOTA hand−held tester to the DLC3.
(f) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
NOTICE:
Do not start the engine.
(g) Select the active test mode on the TOYOTA hand−held
tester.
(h) Please refer to the TOYOTA hand−held tester operator’s
manual for further details.
(i) If you have no TOYOTA hand−held tester, connect the
positive (+) and negative (−) leads from the battery to the
fuel pump connector (See page SF−5).

S01941
S01953
Install
Air Hose
S01948
No.1
No.2
No.3
No.4
Gray
Brown SF−24
− SFIINJECTOR
1996 RAV4 (RM447U)
(f) Tighten the 2 bolts holding the delivery pipe to the cylinder
head.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(g) Install the air hose for the air assist system to the intake
manifold port.
(h) Connect the fuel inlet hose to the fuel filter with 2 new gas-
kets and the union bolt.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
3. INSTALL ENGINE COMPARTMENT R/B NO.2
4. INSTALL EGR VALVE AND PIPE
HINT:
Place a new gasket on the intake manifold.
Torque:
Nut:
13 N·m (130 kgf·cm, 9 ft·lbf)
Union nut:
59 N·m (600 kgf·cm, 43 ft·lbf)
5. CONNECT ENGINE WIRE TO INTAKE MANIFOLD
HINT:
The No.1 and No.3 injector connectors are brown, and the No.2
and No.4 injector connectors are gray.
6. CONNECT THROTTLE BODY TO INTAKE MANIFOLD
7. INSTALL CYLINDER HEAD COVER (See page EM−55
)
8. INSTALL AIR CLEANER ASSEMBLY
9. INSTALL DISTORIBUTOR (See page IG−13)