1996 TOYOTA RAV4 remove transaxle

Q08764
Q08765
Q08766
Q08767
AX−16
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
9. REMOVE ENGINE LEFT MOUNTING BOLT AND NUTS
Torque:
Bolt: 64 N·m (650 kgf·cm, 47 ft·lbf)
Nut: 64 N·m (650 kgf·cm, 47 ft·lbf)
10. REMOVE LEFT AND RIGHT ENGINE UNDER COVERS
11. DRAIN ATF
12. REMOVE LEFT AND RIGHT DRIVE SHAFTS
(See page SA−20)
13. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 bolts and gasket from the exhaust pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used gasket with new gasket.
(b) Remove the 3 nuts, front exhaust pipe and gasket.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used nuts and gasket with new nuts and gasket.
14. DISCONNECT SHIFT CONTROL CABLE
(a) Remove the nut from the control shaft lever.
Torque: 13 N·m (135 kgf·cm, 10 ft·lbf)
(b) Remove the clip and disconnect the control cable.
(c) Remove the 2 shift cable mounting bolts.
Torque: 7.0 N·m (75 kgf·cm, 65 in.·lbf)

Q08774
Q08768
D01757
Q08769
C
D
NutAB C
D
A
B
B
B
Nut
Q08770
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
AX−17
1996 RAV4 (RM447U)
15. DISCONNECT FOLLOWING CONNECTORS
Shift solenoid valve SL connector
Park/neutral position switch connector
Vehicle speed sensor connector
16. DISCONNECT 2 OIL COOLER HOSES
Loosen the 2 clips and disconnect the 2 oil cooler hoses.
17. REMOVE 2 POWER STEERING GEAR MOUNTING
BOLTS AND NUTS
Torque: 113 N·m (1,150 kgf·cm, 83 ft·lbf)
NOTICE:
Support the power steering gear housing securely.
18. REMOVE FRONT SUSPENSION CROSSMEMBER AS-
SEMBLY WITH STABILIZER BAR
Remove the 10 bolts, 2 nuts and front suspension crossmem-
ber assembly with stabilizer bar.
Torque:
A bolt: 206 N·m (2,100 kgf·cm, 152 ft·lbf)
B bolt: 137 N·m (1,400 kgf·cm, 101 ft·lbf)
C bolt: 35 N·m (360 kgf·cm, 26 ft·lbf)
D bolt: 72 N·m (730 kgf·cm, 53 ft·lbf)
Nut: 73 N·m (740 kgf·cm, 54 ft·lbf)
19. REMOVE STIFFENER PLATE
Remove the 3 bolts and stiffener plate.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)

Z18887
A
A
A
B
Q08772
Q08773
A
B AX−18
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
20. REMOVE REAR END PLATE
Remove the 4 bolts and rear end plate.
Torque:
A bolt: 9.0 N·m (95 kgf·cm, 78 in.·lbf)
B bolt: 19 N·m (195 kgf·cm, 14 ft·lbf)
21. REMOVE TORQUE CONVERTER CLUTCH MOUNT-
ING BOLT
Turn the crankshaft to gain access and remove the 6 bolts with
holding the crankshaft pulley set bolt by a wrench.
Torque: 27 N·m (280 kgf·cm, 20 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
First install the gray bolt. Then install 5 black bolts while turning
the crankshaft to grain access.
22. SUPPORT TRANSAXLE WITH A TRANSMISSION
JACK
23. REMOVE TRANSAXLE
Remove the rear side transaxle mouting 2 bolts and transaxle.
Torque:
A bolt: 25 N·m (250 kgf·cm, 18 ft·lbf)
B bolt: 46 N·m (470 kgf·cm, 34 ft·lbf)

AX04K−02
− AUTOMATIC TRANSAXLE (A540H)AUTOMATIC TRANSAXLE SYSTEM
AX−1
1996 RAV4 (RM447U)
AUTOMATIC TRANSAXLE SYSTEM
PRECAUTION
When working with FIPG material, you must observe the followings.
Using a razor blade and a gasket scraper, remove all the old FIPG material from the gasket surfaces.
Thoroughly clean all components to remove all the loose material.
Clean both sealing surfaces with a non−residue solvent.
Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along the sealing surface.
Parts must be assembled within 10 minutes of application. Otherwise, the FIPG material must be re-
moved and reapplied.
If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section.

Q06043
SST
AX04M−02
Q06044
SST
− AUTOMATIC TRANSAXLE (A540H)EXTENSION HOUSING OIL SEAL
AX−3
1996 RAV4 (RM447U)
EXTENSION HOUSING OIL SEAL
ON−VEHICLE REPAIR
1. DRAIN TRANSFER OIL
2. REMOVE PROPELLER SHAFT
(See page PR−3)
3. REMOVE EXTENSION HOUSING OIL SEAL
Using SST, remove the oil seal.
SST 09308−00010
4. INSTALL EXTENSION HOUSING OIL SEAL
(a) Using SST and a hammer, driver in a new oil seal.
SST 09325−20010
Oil seal depth: 1.5 ± 0.4 mm (0.059 ± 0.016 in.)
(b) Coat the lip of the oil seal with MP grease.
5. INSTALL PROPELLER SHAFT
(See page PR−9)
6. FILL TRANSFER WITH OIL
(See page DI−173)

Q08739
AX04N−01
Q06120
Vehicle Speed
SensorO−Ring
Clip Driven Gear
Q08737
Q06119O−Ring
AX−4
− AUTOMATIC TRANSAXLE (A540H)VEHICLE SPEED SENSOR
1996 RAV4 (RM447U)
VEHICLE SPEED SENSOR
ON−VEHICLE REPAIR
1. REMOVE FRONT SPEED SENSOR
(a) Remove the air cleaner assembly.
(b) Disconnect the front speed sensor connector.
(c) Remove the bolt and front speed sensor assembly.
(d) Remove the clip and speedometer driven gear from the
front speed sensor.
(e) Remove the O−ring from the front speed sensor.
2. INSTALL FRONT SPEED SENSOR ASSEMBLY
(a) Coat a new O−ring with ATF and install it to the front
speed sensor.
(b) Install the speedometer driven gear to the front speed
sensor with the clip.
(c) Install the front speed sensor assembly with the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(d) Connect the front speed sensor connector.
(e) Install the air cleaner assembly.
3. REAR SPEED SENSOR
(a) Remove the air cleaner assembly.
(b) Disconnect the rear speed sensor connector.
(c) Remove the bolt and rear speed sensor.
(d) Remove the O−ring from the rear speed sensor.
4. INSTALL REAR SPEED SENSOR
(a) Coat a new O−ring with ATF and install it to the rear speed
sensor.
(b) Install the rear speed sensor with the bolt.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(c) Connect the rear speed sensor connector.
(d) Install the air cleaner assembly.

Q08865
AX04O−01
− AUTOMATIC TRANSAXLE (A540H)ATF TEMPERATURE SWITCH
AX−5
1996 RAV4 (RM447U)
ATF TEMPERATURE SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. REMOVE ATF TEMPERATURE SWITCH
(a) Disconnect the ATF temperature switch connector.
(b) Remove the ATF temperature switch.
3. INSTALL ATF TEMPERATURE SWITCH
(a) Install the ATF temperature switch.
(b) Connect the ATF temperature switch connector.
4. INSTALL NO.2 ENGINE UNDER COVER

Q08738
AX128−01
Q06066
Q06109
Q06077NRP AX−6
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft with the 2 bolts and nut.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Temporarily install the manual valve lever shaft.
(e) Turn the lever counterclockwise until it stops, then turn it
clockwise 2 notches.
(f) Remove the shaft control lever.