1996 TOYOTA RAV4 clock

AT0953
SST
AX05A−02
AT3306
Hold
Lock
Free
Turn
D00776
AT4184
AX−20
− AUTOMATIC TRANSAXLE (A241E)TORQUE CONVERTER CLUTCH AND DRIVE PLATE
1996 RAV4 (RM447U)
TORQUE CONVERTER CLUTCH
AND DRIVE PLATE
INSPECTION
1. INSPECT ONE−WAY CLUTCH
(a) Install SST into the inner race of the one−way clutch.
SST 09350−32014 (09351−32010)
(b) Install SST so that it fits in the notch of the converter clutch
hub and outer race of the one−way clutch.
SST 09350−32014 (09351−32020)
(c) With the torque converter clutch standing on its side,the
clutch locks when turned counterclockwise, and rotates
freely and smoothly clockwise.
If necessary, clean the converter clutch and retest the clutch.
Replace the converter clutch if the clutch still fails the test.
2. MEASURE DRIVE PLATE RUNOUT AND INSPECT
RING GEAR
Set up a dial indicator, measure the drive plate runout.
Maximum runout: 0.20 mm (0.0079 in.)
If the runout is not within the specification or if the ring gear is
damaged, replace the drive plate. If installing a new drive plate,
note the orientation of spacers and tighten the bolts.
Torque: 83 N·m (850 kgf·cm, 61 ft·lbf)
3. MEASURE TORQUE CONVERTER CLUTCH SLEEVE
RUNOUT
Temporarily mount the torque converter clutch to the drive
plate. Set up a dial indicator, measure the torque converter
clutch sleeve runout.
Maximum runout: 0.30 mm (0.0118 in.)
If the runout is not within the specification, try to correcting by
reorienting the installation of the converter clutch.

Q08738
AX128−01
Q06066
Q06109
Q06077NRP AX−6
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft with the 2 bolts and nut.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Temporarily install the manual valve lever shaft.
(e) Turn the lever counterclockwise until it stops, then turn it
clockwise 2 notches.
(f) Remove the shaft control lever.

AT0952
SST
AX04W−01
AT0953
SST
AT3306
Hold
Lock
Free
Turn
AT2821
AX−22
− AUTOMATIC TRANSAXLE (A540H)TORQUE CONVERTER CLUTCH AND DRIVE PLATE
1996 RAV4 (RM447U)
TORQUE CONVERTER CLUTCH
AND DRIVE PLATE
INSPECTION
1. INSPECT ONE−WAY CLUTCH
(a) Install SST into the inner race of the one−way clutch.
SST 09350−32014 (09351−32010)
(b) Install SST so that it fits in the notch of the converter clutch
hub and outer race of the one−way clutch.
SST 09350−32014 (09351−32020)
(c) With the torque converter clutch standing on its side, the
clutch locks when turned counterclockwise, and rotates
freely and smoothly clockwise.
If necessary, clean the converter clutch and retest the clutch.
Replace the converter clutch if the clutch still fails the test.
2. MEASURE DRIVE PLATE RUNOUT AND INSPECT
RING GEAR
(a) Set up a dial indicator and measure the drive plate runout.
(b) Check the damage of the ring gear.
Maximum runout: 0.20 mm (0.0079 in.)
If the runout is not within the specification, or ring gear is dam-
aged replace the drive plate.
Torque: 83 N·m (850 kgf·cm, 61 ft·lbf)

Z10844
Z15867
UP
DOWN
BE−54
− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1996 RAV4 (RM447U)
(2) Attach a current−measuring probe to terminal 6 of
the wire harness.
(3) Turn the ignition switch ON and set the power win-
dow switch in the down position.
(4) As the window goes down, check that the current is
approximately 7 amperes.
(5) Check that the current increases up to approxi-
mately 14.5 amperes or more when the window
stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so that check must be made before the
circuit breaker operates.
If operation is not as specified, replace the master switch.
7. INSPECT FRONT POWER WINDOW SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
UP1 − 2, 3 − 4Continuity
OFF1 − 2, 3 − 5Continuity
DOWN1 − 4, 3 − 5Continuity
If continuity is not as specified, replace the switch.
8. 5 Door models:
INSPECT REAR POWER WINDOW SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
UP1 − 2, 3 − 4Continuity
OFF1 − 2, 4 − 5Continuity
DOWN2 − 3, 4 − 5Continuity
If continuity is not as specified, replace the switch.
9. Driver ’s door of 3 door models:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns counterclockwise.

N11404
1
2
N11405
1
2
Z15868
21
Z15869
21
− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE−55
1996 RAV4 (RM447U)
(b) Reverse the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.
10. Passenger ’s door of 3 door models:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns clockwise.
(b) Revers the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.
11. Driver ’s door of 5 door models:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns clockwise.
(b) Reverse the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.

Z15870
21
Z15871
21
Z15872
21
Z15873
21
Z15874
21 BE−56
− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1996 RAV4 (RM447U)
12. Passenger ’s door of 5 door models:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns clockwise.
(b) Reverse the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.
13. 5 Door models:
INSPECT LH REAR POWER WINDOW MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns clockwise.
(b) Reverse the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.
14. 5 Door models:
INSPECT RH REAR POWER WINDOW MOTOR OP-
ERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2, check that the
motor turns clockwise.

Z15875
21
Z17551
within
4 to 40
secondsUP
UP
3 Door 5 Door
Z17552
within
60
seconds3 Door 5 DoorDOWN
DOWN
Z10682
within
4 to 40
secondsUP
Z10683
within
60 secondsDOWN
− BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE−57
1996 RAV4 (RM447U)
(b) Reverse the polarity, check that the motor turns counter-
clockwise.
If operation is not as specified, replace the motor.
15. Driver ’s Door:
INSPECT CIRCUIT BREAKER OPERATION
(a) With the window in the fully closed position, hold the pow-
er window switch in ”UP” position and check that there is
a circuit breaker operation noise within 4 to 40 seconds.
(b) With the window in the fully closed position, hold the
switch in ”DOWN” position and check that the window be-
gins to descend within 60 seconds.
If operation is not as specified, replace the motor.
16. Passenger ’s Door:
INSPECT CIRCUIT BREAKER OPERATION
(a) With the window in the fully closed position, hold the pow-
er window switch in ”UP” position and check that there is
a circuit breaker operation noise within 4 to 40 seconds.
(b) With the window in the fully closed position, hold the
switch in ”DOWN” position and check that the window be-
gins to descend within 60 seconds.
If operation is not as specified, replace the motor.

BR0M7−01
R10719
R00285
R10696
SST
R10720
SST BR−30
− BRAKEREAR DRUM BRAKE
1996 RAV4 (RM447U)
REMOVAL
1. INSPECT SHOE LINING THICKNESS
Remove the inspection hole plug, and check the shoe lining
thickness through the hole.
If less than minimum, replace the shoes.
Minimum thickness: 1.0 mm (0.039 in.)
2. REMOVE REAR WHEEL
3. REMOVE BRAKE DRUM
HINT:
If the brake drum cannot be removed easily, do the following
steps.
(a) Insert a bent wire or an equivalent through the hole in the
brake drum, and hold the automatic adjusting lever away
from the adjuster.
(b) Using a screwdriver, reduce the brake shoe adjustment
by turning the adjuster.
HINT:
At the time of installation, please refer to the following item.
Align the hub’s large hole next to the small hole in the clockwise
direction with the drum’s plug hole.
4. REMOVE FRONT SHOE
(a) Using SST, remove the return spring.
SST 09703−30010
(b) Using SST, remove the shoe hold−down spring, cups and
pin.
SST 09718−00010
(c) Disconnect the anchor spring from the front shoe and re-
move the front shoe.
(d) Remove the anchor spring from the rear shoe.