1996 TOYOTA RAV4 torque

pairing phone coolant temperature coolant tire pressure reset battery replacement heating

Page 899 of 1354

TOYOTA RAV4 1996 Service Repair Manual 130
ELECTRONICALLY CONTROLLED TRANSMISSION
THIS SYSTEM ELECTRONICALLY CONTROLS THE GEAR SHIFT TIMING, LOCK-UP TIMING, THE CLUTCH AND BRAKE HYDRAULIC
PRESSURE, AND THE ENGINE TORQUE DURING SHIFTING TO

130
ELECTRONICALLY CONTROLLED TRANSMISSION
THIS SYSTEM ELECTRONICALLY CONTROLS THE GEAR SHIFT TIMING, LOCK-UP TIMING, THE CLUTCH AND BRAKE HYDRAULIC
PRESSURE, AND THE ENGINE TORQUE DURING SHIFTING TO ACHIEVE OPTIMUM SHIFT FEELING.
IN ACCORDING TO THE VEHICLE DRIVING CONDITIONS AND ENGINE OPERATING CONDITIONS AS DETECTED BY VARIOUS
SENSORS.
1. GEAR SHIFT OPERATION
DURING DRIVING, THE ENGINE CONTROL MODULE SELECTS THE SHIFT FOR EACH GEAR WHICH IS MOST APPROPRIATE TO THE
DRIVING CONDITIONS, BASED ON INPUT SIGNALS FROM THE ENGINE COOLANT TEMP. SENSOR TO TERMINAL THW OF THE
ENGINE CONTROL MODULE, AND ALSO THE INPUT SIGNALS TO TERMINAL SPD OF THE ENGINE CONTROL MODULE FROM THE
SPEEDOMETER DEVOTED TO THE ELECTRONICALLY CONTROLLED TRANSMISSION. CURRENT IS THEN OUTPUT TO THE
ELECTRONICALLY CONTROLLED TRANSMISSION SOLENOID. WHEN SHIFTING TO 1ST SPEED, CURRENT FLOWS FROM TERMINAL
S1 OF THE ENGINE CONTROL MODULE "TERMINAL
(A) 3 (2WD) OR (B) 3 (4WD) OF THE ELECTRONICALLY CONTROLLED
TRANSMISSION SOLENOID "GROUND, AND CONTINUES TO THE NO. 1 SOLENOID CAUSES THE SHIFT.
FOR 2ND SPEED, CURRENT FLOWS FROM TERMINAL S1 OF THE ENGINE CONTROL MODULE "TERMINAL 3 OF THE
ELECTRONICALLY CONTROLLED TRANSMISSION SOLENOID "GROUND, AND FROM TERMINAL S2 OF THE ENGINE CONTROL
MODULE "TERMINAL
(A) 1 (2WD) OR (B) 6 (4WD) OF THE ELECTRONICALLY CONTROLLED TRANSMISSION SOLENOID "
GROUND, AND CONTINUES TO SOLENOIDS NO. 1 AND NO. 2 CAUSES THE SHIFT.
FOR 3RD SPEED, THERE IS NO CONTINUOUS TO NO. 1 SOLENOID, ONLY TO NO. 2 CAUSING THE SHIFT.
SHIFTING INTO 4TH SPEED (OVERDRIVE) TAKES PLACE WHEN THERE IS NO CONTINUOUS TO EITHER NO. 1 OR NO. 2 SOLENOID.
2. LOCK-UP OPERATION
WHEN THE ENGINE CONTROL MODULE JUDGES FROM EACH SIGNAL THAT LOCK-UP OPERATION CONDITIONS HAVE BEEN MET,
CURRENT FLOWS FROM TERMINAL SL OF THE ENGINE CONTROL MODULE "TERMINAL
(A) 2 (2WD) OR (B) 5 (4WD) OF THE
ELECTRONICALLY CONTROLLED TRANSMISSION SOLENOID "GROUND, CONTINUES TO THE LOCK-UP SOLENOID AND CAUSING
LOCK-UP OPERATION.
3. STOP LIGHT SW CIRCUIT
IF THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) WHEN DRIVING IN LOCK-UP CONDITION, A SIGNAL IS INPUT TO
TERMINAL B/K OF THE ENGINE CONTROL MODULE, THE ENGINE CONTROL MODULE OPERATES AND CURRENT TO THE LOCK-UP
SOLENOID IS CUT.
4. OVERDRIVE CIRCUIT
*O/D MAIN SW ON
WHEN THE O/D MAIN SW IS TURNED ON (SW POINT IS OPEN), A SIGNAL IS INPUT TO TERMINAL OD2 OF THE ENGINE CONTROL
MODULE AND ENGINE CONTROL MODULE OPERATION CAUSES GEAR SHIFT WHEN THE CONDITIONS FOR OVERDRIVE ARE MET.
*O/D MAIN SW OFF
WHEN THE O/D MAIN SW IS TURNED OFF (SW POINT IS CLOSED), THE CURRENT FLOWING THROUGH THE O/D OFF INDICATOR
LIGHT FLOWS THROUGH THE O/D MAIN SW TO GROUND. CAUSING THE INDICATOR LIGHT TO LIGHT UP. AT THE SAME TIME, A
SIGNAL IS INPUT TO TERMINAL OD2 OF THE ENGINE CONTROL MODULE AND ENGINE CONTROL MODULE OPERATION
PREVENTS SHIFT INTO OVERDRIVE.
SYSTEM OUTLINE