1996 TOYOTA LAND CRUISER shocks

IN−10
−
INTRODUCTION FOR ALL OF VEHICLES
10
Author: Date:
1996 LAND CRUISER (RM451U)
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad (See page
RS−9) and front passenger airbag assembly (See
page RS−23 ) should be inspected.
(4) Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly, steering wheel pad or front passenger air-
bag assembly in order to reuse them.
(7) If the airbag sensor assembly, steering wheel pad
or front passenger airbag assembly have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not directly expose the airbag sensor assembly, steering wheel pad or front passenger airbag as-
sembly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kΩ/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of the SRS components. Follow the instructions on the
notices.
(11) After work on the supplemental restraint system is completed, check the SRS warning light (See page
DI−240 ).
(c) SPIRAL CABLE (in Combination Switch) The steering wheel must be fitted correctly to the steering
column with the spiral cable at the neutral position, other-
wise cable disconnection and other troubles may result.
Refer to SR−19 of this manual concerning correct steer-
ing wheel installation.
RedMarkROOJll
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2810
AC2QA−01
AC2811
N11084
Wrong Okay
LO HI LOHI
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
AC−1
1328
Author: Date:
1996 LAND CRUISER (RM451U)
AIR CONDITIONING SYSTEM
PRECAUTION
1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED
AREA OR NEAR AN OPEN FLAME
2. ALWAYS WEAR EYE PROTECTION
3. BE CAREFUL THAT LIQUID REFRIGERANT DOES NOT GET IN YOUR EYES OR ON YOUR SKIN
If liquid refrigerant gets in your eyes or on your skin:
(a) Wash the area with lots of cool water.
CAUTION:
Do not rub your eyes or skin.
(b) Apply clean petroleum jelly to the skin.
(c) Go immediately to a physician or hospital for professional treatment.
4. NEVER HEAT CONTAINER OR EXPOSE IT TO NAKED
FLAME
5. BE CAREFUL NOT TO DROP CONTAINER AND NOT TO APPLY PHYSICAL SHOCKS TO IT
6. DO NOT OPERATE COMPRESSOR WITHOUT ENOUGH REFRIGERANT IN REFRIGERANT SYSTEM
If there is not enough refrigerant in the refrigerant system oil lu-
brication will be insuf ficient and compressor burnout may occur,
so take care to avoid this.
7. DO NOT OPEN HIGH PRESSURE MANIFOLD VALVE WHILE COMPRESSOR IS OPERATING
If the high pressure valve is opened, r efrigerant flows in the re-
verse direction and could cause the charging cylinder to rup-
ture, so open and close the only low pressure valve.
8. BE CAREFUL NOT TO OVERCHARGE SYSTEM WITH
REFRIGERANT
If refrigerant is overcharged, it causes problems such as insuffi-
cient cooling, poor fuel economy, engine overheating etc.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MD−01
BE−34
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SPEEDOMETER ON−VEHICLE:
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
If error is excessive, replace the speedometer.
Standard indicationAllowable range
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
120118 − 132
2. INSPECT NO.1 VEHICLE SPEED SENSOR OPERA-
TION
(a) Connect the positive (+) lead from battery to terminal 1 and negative ( −) lead to terminal 2.
(b) Connect the positive (+) lead from tester to terminal 3 and
the negative ( −) lead to terminal 2.
(c) Revolve shaft.
(d) Check that there is voltage changer from approx. 0 V to 11 V or more between terminals 3 and 2.
HINT:
The voltage change should be 4 times per each revolution of
the No.1 vehicle speed sensor shaft.
If operation is not as specified, replace the sensor.
3. INSPECT TACHOMETER ON−VEHICLE:
(a) Connect a tune− up test tachometer, and start the engine.
NOTICE:
Reversing the connection of the tachometer will damage
the transistors and diodes inside.When removing or instal-
ling the tachometer, be careful not to drop or subject it to
heavy shocks.
(b) Compare the tester and tachometer indications.
If error is excessive, replace the tachometer.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

RS0OZ−02
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
RS−1
1100
Author: Date:
1996 LAND CRUISER (RM451U)
SRS AIRBAG
PRECAUTION
NOTICE:
The LAND CRUISER is equipped with an SRS , which comprises a driver airbag \
and a front pas-
senger airbag. Failure to carry out service operations in the correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serio\
us accident. Further,
if a mistake is made in servicing the SRS, it is possible the SRS may fail to\
operate when re-
quired. Before performing servicing (including removal or installation \
of parts, inspection or
replacement), be sure to read the following items carefully, then follow the correct procedure
described in the repair manual.
Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the mos\
t impor-
tant source of information when troubleshooting. When troubleshooting th\
e SRS, always in-
spect the DTCs before disconnecting the battery.
Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front
passenger airbag assembly, and airbag sensor assembly should be inspected (See pages
RS−9 , RS−23 and RS−34 )
Never use SRS parts from another vehicle. When replacing parts, replace them with \
new parts.
Never disassemble and repair the steering wheel pad, front passenger airbag assembly , or air-
bag sensor assembly in order to reuse it.
If the steering wheel pad, front passenger airbag assembly or airbag sen\
sor assembly have
been dropped, or if there are cracks, dents or other defects in the case, br\
acket or connector,
replace them with new ones.
Use a volt/ohmmeter wi th high impedance (10 k Ω/V minimum) for troubleshooting the system’s
electrical circuits.
Information labels are attached to the periphery of the SRS components. Follow the instruc-
tions on the notices.
After work on the SRS is completed, check the SRS warning light (See pa\
ge DI−240).
If the vehicle is equipped with a mobile communication system, refer to the precaution in the
IN section.
CAUTION:
Work must be started after 90 seconds from the time the ignition switch is t\
urned to the ”LOCK”
position and the negative ( −) terminal cable is disconnected from the battery.
(The SRS is equipped with a back− up power source so that if work is started within 90 seconds
of disconnecting the negative ( −) terminal cable of the battery, the SRS may be deployed.)
When the negative (−) terminal cable is disconnected from the battery, the memory of the clock
and audio system will be canceled. So before starting work, make a record o\
f the contents mem-
orized in the audio memory system. When work is finished, reset the audio syst\
ems as they
were before and adjust the clock. To avoid erasing the memory of each memory system, never
use a back−up power supply from outside the vehicle.
Before repairs, remove the airbag sensor if shocks are likely to be applied to the senso\
r during
repairs.
Do not expose the steering wheel pad, front passenger airbag assembly, or airbag sensor as-
sembly directly to hot air or flames.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010