1996 TOYOTA LAND CRUISER Front diff

SA1VL−03
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−101
958
Author: Date:
1996 LAND CRUISER (RM451U)
DIFFERENTIAL LOCKING SYSTEM
ON−VEHICLE INSPECTION
1. INSPECT DIFFERENTIAL LOCK SYSTEM
(a) Inspect the indicator lights.
Check that the indicator lights (front side and rear side)
light up for approx. 1 second when the ignition switch is
turned ON.
(b) Inspect the differential lock operation. (1) Jack up the vehicle then start the engine.
(2) Put the transfer shift lever on the L position.
(3) When the Diff. lock control switch is set to the RR
position, the indicator light (rear side) is turned on.
Differential lock is applied to the rear wheel at this
time.
HINT:
If the gears of the differential lock system are not meshed, the
indicator light remains blinking, so rotate the tires to mesh the
gear.
(4) When the Diff. lock control switch is at the OFF posi-
tion, the indicator light goes off.
Differential lock is released for the rear wheel at this
time.
(5) When the Diff. lock control switch is set to the FR/ RR position, the indicator lights (front side and rear
side) are turned on.
Differential lock is applied to both the front wheels
and rear wheels at this time.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z07254
M3 M4 M1 M2
Z07255
Wire Harness Side
SA−102
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
959
Author: Date:
1996 LAND CRUISER (RM451U)
(6) Check the voltage between the terminals of the Diff.
lock ECU when switching the Diff. lock control
switch with the speedometer, registering approx. 8
km/h (5 mph) or more.
(7) Check that the indicator lights blink when center Diff. lock release mode is set.
Diff. lock is released for both the front wheels and
rear wheels at this time.
(8) Return the Diff. lock control switch to OFF.
(9) Stop the engine and lower the vehicle.
2. INSPECT DIFF. LOCK SYSTEM CIRCUIT
(a) Inspect the system circuit with connector disconnected. Disconnect the connector from the Diff. lock ECU and in-
spect the connector on the wire harness side, as shown
in the chart.
Trouble Part/
Terminals (Symbols)ConditionSpecified V alue
Rear diff. lock actuator/
1 (M2) − 3 (M1)−Less than 100 Ω
Front diff. lock actuator/
5 (M4) − 7 (M1)−Less than 100 Ω
Body ground/
13 (GND) − Body ground−Continuity
Vehicle speed sensor/
4(SPD) − Body groundVehicle moving slowly1 pulse each 40 cm (15.75 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z07256
ECU Side
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−103
960
Author: Date:
1996 LAND CRUISER (RM451U) DIFF. fuse/
8 (IG) − Body ground
Ignition switch ONBattery positive voltage
Rear diff. lock position switch/
2 (RLP) − Body groundIgnition switch ON,
Indicator light (Rear) ONAbout 0 V
Ignition switch ON,
Indicator light (Rear) OFFBattery positive voltage
Front diff. lock position switch/ 9 (FLP) − Body ground
Ignition switch ON,
Indicator light (front) ON.About 0 V
Ignition switch ON,
Indicator light (front) OFFBattery positive voltage
Center diff. indicator switch/ 15 (4WD) − Body groud
Ignition switch ON,
Indicator light (Center diff. lock) ONAbout 0 V
Ignition switch ON,
Indicator light (Ce nter diff. lock) OFFBattery positive voltage
Differential lock control switch/
12 (R) − Body ground
Ignition switch ON,
Diff. lock control switch RR or FR RRBattery positive voltage
Ignition switch ON,
Diff. lock control switch OFFAbout 0 V
Differential lock control switch/ 6 (RF) − Body ground
Ignition switch ON,
Diff. lock control switch FR RRBattery positive voltage
Ignition switch ON,
Diff. lock control switch OFF or RRAbout 0 V
HINT:
When a signal enters the ECU to LOCK the front dif ferential and
set the rear differential to FREE (when battery positive voltage
is inputted to terminal 6 (RF) of ECU and about 0 V is inputted
to terminal 12 (R)), or a signal to FREE both the front and rear
differentials, the indicator lights keep blinking until the ignition
switch is turned off (Fail−safe function).
If the circuit is not as specified, check and repair or replace the
trouble part shown in the table above.
(b) Inspect the battery positive voltage Battery positive voltage: 10 − 14.5 V
(c) Inspect the system circuit with connector connected (1) Turn the ignition switch to the ON position.
(2) Keep the center Diff. lock condition.
(3) Remove the Diff. lock ECU.
(4) Using a voltmeter, measure the voltage when thedifferential lock control switch is in the position, as
shown below.
Terminals (Symbols)Switch PositionSTD Voltage (V)
15 (4WD) − 13 (GND)−0.5 or less
9 (FLP) − 13 (GND)FR RR0.5 or less
2 (RLP) − 13 (GND)RR or FR RR0.5 or less
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1948
21
4
Z07264
Ohmmeter
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−105
962
Author: Date:
1996 LAND CRUISER (RM451U)
4. INSPECT DIFF. LOCK CONTROL SWITCH
Inspect the switch continuity between terminals, as shown.
Switch PositionTerminalsSpecified Condition
OFF1 − 2No continuity
1 − 4No continuity
RR1 − 2No continuity
1 − 4Continuity
FR RR1 − 2Continuity
1 − 4Continuity
If continuity is not as specified, replace the switch.
5. INSPECT DIFF. LOCK POSITION SWITCH
(a) Front and Rear:
Inspect the diff. lock position switch.
(1) Check that there is continuity between terminalswhen the switch is pushed (differential connected
position).
(2) Check that there is no continuity when the switch is
free (differential disconnected position).
If operation is not as specified, replace the switch.
(b) Inspect the center diff. indicator switch.
6. INSPECT VEHICLE SPEED SENSOR AND INDICATOR
LIGHT
(a) Inspect the vehicle speed sensor (See page BE−34).
(b) Inspect the indicator light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VN−02
Z07258
Z07261
SA2619
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−107
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT ACTUATOR
(a) Shifting the front differential lock.
(b) Disconnect the connector and tube.
(c) Remove the 2 nuts, bolt and actuator.
(d) Remove the O−ring from the actuator.
2. REMOVE REAR ACTUATOR
(a) Shifting the gear differential lock.
(b) Remove the actuator protector.
Remove the 2 nuts, bolt and protector.
(c) Disconnect the connectors and tube.
(d) Remove the rear Diff. lock position switch.
(e) Remove the cover. (1) Remove the 3 bolts.
(2) Using a brass bar and hammer, remove the cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VO−02
Z07259
Outside
Actuator Installation
Hole Shift Fork
R08154
3
2
1.5
50 °
108 °
Matchmark
(Groove)
SA2306
SA2420
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−109
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FRONT ACTUATOR
(a) Check that the outermost rack tooth of the shift fork is
virtually above the center line of the actuator installation
hole.
(b) Using a dry cell battery, alig n the matchmark on the pinion
with the center line of the actuator.
NOTICE:
If the pinion of the actuator is not in the specified
place, the actuator is difficult to be installed.
Do not supply the battery positive voltage between
terminals.
If the matchmark comes to the extension limit of the
rotation, do not electrify moreover.
(c) Install a new O−ring to the actuator.
(d) Apply a light coat of gear oil on the O −ring.
(e) Apply MP grease to the gear part of the actuator.
(f) Install the actuator to the differential with the 2 nuts and bolt, so that the outermost rack tooth of the shift fork will
fit matchmark of the pinion of the actuator.
HINT:
Do not damage the O −ring of the actuator.
Torque: 26 N·m (270 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z15220
FIPG Width Approx.
1 − 2 mm (0.04 − 0.08 in.)
Z07262Adhesive
SA2620
SA−11 0
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
1996 LAND CRUISER (RM451U)
(g) Connect the connector and tube.
HINT:
The depth of the insertion of the bleeder tube into the
hose is approx. 15 mm (0.59 in.).
Take care that water or the equivalent will not adhere to
the connector and hose.
(h) Cancel the front differential lock.
With the ignition switch ON, turn the differential lock con-
trol switch to OFF to cancel the differential lock.
2. INSTALL REAR ACTUATOR
(a) Clean contacting surfaces of any FIPG material using gasoline or alcohol.
(b) Apply FIPG to the actuator. FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
HINT:
Install the actuator within 10 minutes after applying FIPG.
(c) Install the actuator to the differential and match the shaft with the shaft fork hole.
(d) Clean the threads of the set bolt and shaft fork with the white gasoline.
(e) Coat the threads of the set bolt with adhesive.
Adhesive: Part No. 08833 −00070, THREE BOND 1324
or equivalent
(f) Tighten the shift fork set bolt. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(g) Tighten the 4 bolts uniformly, a little at a time. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(h) Install the cover. (1) Clean the contacting surfaces of any FIPG material
using gasoline or alcohol.
(2) Apply FIPG to the cover.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
HINT:
Install the cover within 10 minutes after applying FIPG.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS−8
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1996 LAND CRUISER (RM451U)
A/C compressor bracket x No. 1 oil pan
3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil check valve x Cylinder block2525018
Main bearing cap x Cylinder block
1st
2nd74
Turn 90°750
Turn 90°54
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd48
Turn 90°490
Turn 90°35
Turn 90°
Rear oil seal retainer x Cylinder block2121015
Oil cooler cover x Cylinder block2121015
LH engine mounting bracket x Cylinder block6970051
LH insulator x LH engine mounting bracket7273043
RH engine mounting bracket x Cylinder brock6970051
RH insulator x RH engine mounting bracket7273043
PS pump x Cylinder block3637027
Knock sensor x Cylinder block4445033
Oil filter union x Cylinder block4445033
Drive plate x Crankshaft1001,00074
Transmission x Cylinder block7273053
Transmission x No. 1 oil pan7273053
Torque converter clutch x Drive plate5555041
A/T oil cooler pipe x Union (Transmission)3435025
Starter x Transmission3940029
Frame crossmember x Frame6162045
Frame crossmember x Engine rear mounting insulator7475054
Engine front mounting insulator x Frame7475054
Transfer shift lever x Transmission1818513
Transmission shift lever assembly x Body5.45548 in.·lbf
Transmission control rod x Control shaft lever131309
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Rear differential8890065
Rear propeller shaft x Transfer8890065
Stabillizer bar bracket mounting bolt1818513
Stabillizer bar x Axle carrier2526019
PS pressure hose x PS pump5657542
Rear TWC x Center pipe4040029
Center pipe x Tailpipe4040029
Heated oxygen sensor (Bank 1 sensor 1) x Front exhaust pipe2020014
Heated oxygen sensor (Bank 1 sensor 2) x Center pipe2020014
No. 2 support bracket x Frame18.518513
No. 3 support bracket x Frame18.518513
No. 4 support bracket x Frame18.518513
Exhaust pipe damper x Tailpipe19.519514
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010