1996 TOYOTA LAND CRUISER Front diff

Q04610
Q00541
Front
Q02950
Q07125
FIPG
−
TRANSFER TRANSFER ASSEMBLY
TR−5
1996 LAND CRUISER (RM451U)
6. REMOVE TRANSFER INDICATOR SWITCH
Remove the Center Diff Lock indicator switch, L4 position
switch, Neutral position switch and 3 gaskets.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
7. REMOVE FRONT EXTENSION HOUSING
Remove the 6 bolts and front extension housing.
HINT:
If necessary, tap the front extension housing with a plastic ham-
mer.
HINT:
At the time of reassembly, please refer to the following items.
Set the clutch sleeve in differential lock condition.
Apply FIPG to the front case.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
8. REMOVE CLUTCH SLEEVE, SHIFT FORK NO.2 SHAFT AND SHIFT FORK NO.2
HINT:
At the time of reassebly, make sure to install the clutch sleeve
in the correct direction.
9. SEPARATE SHIFT FORK NO.2 SHAFT AND SHIFT FORK NO.2
(a) Using 2 screwdrivers and a hammer, tap out the 3 snap rings from the shift fork No.2 shaft.
(b) Separate the shift fork No.2 shaft and shift fork No.2.
10. REMOVE REAR EXTENSION HOUSING
Remove the 9 bolts and rear extension housing.
HINT:
If necessary, tap the rear extension housing with a plastic ham-
mer.
HINT:
At the time of reassembly, apply FIPG to the rear case. FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0854
TF0986
TF0857
Q07130
RemovalInstallation
Socket Wrench Socket Wrench
TR−8
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
16. REMOVE 2 BEARING RACES FROM REAR CASE
17. REMOVE INPUT SHAFT ASSEMBLY
Using a plastic hammer, remove the input shaft assembly.
18. REMOVE IDLER GEAR ASSEMBLY, CENTER DIFFER-
ENTIAL ASSEMBLY, SHIFT FORK NO.1 AND SHIFT
FORK NO.1 SHAFT FROM FRONT CASE
19. SEPARATE SHIFT FORK NO.1 AND SHIFT FORK NO.1 SHAFT
(a) Using a pin punch and hammer, drive out the slotted spring pin.
(b) Separate the shift fork No.1 and shift fork No.1 shaft.
20. REMOVE SHIFT OUTER LEVER AND INNER LEVER
(a) Remove the nut and washer from the shift outer lever. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Using a brass bar, hammer and socket wrench, tap out the lever lock pin.
(c) Remove the shift outer lever, washer and inner lever from
the front case.
21. REMOVE OIL RECEIVER FROM FRONT CASE
Remove the bolt and oil receiver. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BB−01
Q07134
Front Drive Gear
PieceHigh
Speed Output GearHigh Speed Output
Gear Bushing
Clutch HubHigh and Low
Clutch Sleeve Rear Taper Roller
Bearing
 Snap Ring
Needle Roller Bearing
Thrust Washer
Thrust Washer Rear Side Gear
Straight Pin x 12
Differential Rear Case
Thrust Washer
Pinion
Gear
Pinion Shaft
Front Side Gear
Thrust Washer
Differential Front Case
 Non− reusable part Low Gear
Straight Pin

Snap Ring Front T
aper Roller BearingNeedle Roller Bearing
Pinion Gear
TR−18
−
TRANSFER CENTER DIFFERENTIAL
828
Author: Date:
1996 LAND CRUISER (RM451U)
CENTER DIFFERENTIAL
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BC−01
TF0900
TF0944
Q07101
SST
Q07102
SST
Q07103
SST
−
TRANSFER CENTER DIFFERENTIAL
TR−19
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND
THRUST CLEARANCE
(a) Using a feeler gauge, measure the high speed output gear thrust clearance.
Standard clearance:
0.10−0.25 mm (0.0039 −0.0098 in.)
Maximum clearance:
0.25 mm (0.0098 in.)
(b) Using a dial indicator, measure the high speed output gear radial clearance.
Standard clearance:
0.035−0.091 mm (0.0014 −0.0036 in.)
Maximum clearance:
0.091 mm (0.0036 in.)
2. REMOVE FRONT DRIVE GEAR PIECE
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST and a press, remove the front drive gear piece.
SST 09950−00020, 09950 −60010 (09951−00320)
NOTICE:
Be careful not to drop the center differential assembly.
3. REMOVE FRONT TAPER ROLLER BEARING
Using SST and a press, remove the front taper roller bearing.
SST 09950−00020
4. REMOVE HIGH SPEED OUTPUT GEAR
5. REMOVE NEEDLE ROLLER BEARING
6. REMOVE HIGH AND LOW CLUTCH SLEEVE AS-
SEMBLY
7. REMOVE HIGH SPEED OUTPUT GEAR BUSHING AND CLUTCH HUB
(a) Using SST and a press, remove the high speed output
gear bushing and clutch hub.
SST 09550−00020, 09950 −00030, 09950−60010
(09951 −00320)
(b) Using a magnetic finger, remove the straight pin from the
differential front case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07113
SST
Q07114
SST
SST
Bearing
TR−20
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U)
8. REMOVE REAR TAPER ROLLER BEARING
Using SST and a press, remove the rear taper roller bearing.
SST 09950−00020, 09950 −60010 (09951−00320)
9. REMOVE DIFFERENTIAL REAR CASE
Remove the 12 bolts and differential rear case.
10. REMOVE REAR SIDE GEAR AND THRUST WASHER
11. REMOVE PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Remove the straight pin from the pinion shaft.
(b) Remove the pinion shaft, 2 pinion gears and thrust wash-
ers.
(c) Remove the front side gear and thrust washer.
12. REMOVE LOW GEAR
Using a plastic hammer, tap and remove the low gear.
NOTICE:
Be careful not to damage the low gear.
13. REMOVE NEEDLE ROLLER BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a hammer, remove the needle roller bear-
ing from the differential rear case.
SST 09223 −00010, 09950 −60010 (09951 −00400),
09950 −70010 (09951 −07150)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BD−01
Q07115
SSTStamp
TF1012
TF0913
TF0917
−
TRANSFER CENTER DIFFERENTIAL
TR−21
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the differential rear case.
SST 09612−24014 (09612 −10050)
HINT:
Install the bearing to the differential rear case, taking care that
its stamped side comes in contact with SST.
(b) Install the snap ring.
2. INSTALL LOW GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the low gear in boiling water.
(c) Carefully remove the low gear from the water.
(d) After the moisture on the low gear has completely evapo- rated, quickly install the low gear to the differential case.
3. INSTALL PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Install the front side gear and thrust washer to the differ- ential front case.
(b) Install the pinion shaft, 2 pinion gears and thrust washers
to the differential front case.
(c) Using a dial indicator, measure the front case backlash.
HINT:
Push the pinion shaft. Minimum backlash: 0.05 mm (0.0020 in.)
If the backlash is not within the specification, replace the thrust
washer with one of the correct size and reinstall the thrust wash-
er.
Thickness mm (in.)Thickness mm (in.)
1.70 (0.0669)2.45 (0.0965)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q00546
SST
Q00555
Q00539
SSTSST
Q00540
SST
SST
TF0931
−
TRANSFER CENTER DIFFERENTIAL
TR−23
1996 LAND CRUISER (RM451U)
(c) Using SST and a press, install the high speed output gear
bushing.
SST 09316−12010, 09316 −60011 (09316−00011)
NOTICE:
Before pressing, align the holes on the bushing and shaft
so that the pin on the shaft aligned with the cutting portion
of the bushing.
11. INSTALL HIGH AND LOW CLUTCH SLEEVE
HINT:
Make sure to install the high and low clutch sleeve in the correct
direction.
12. INSTALL HIGH SPEED OUTPUT GEAR AND NEEDLE ROLLER BEARING
(a) Apply gear oil to the needle roller bearing.
(b) Install the high speed output gear and needle roller bear-
ing.
13. INSTALL FRONT TAPER ROLLER BEARING
Using SST and a press, install the front taper roller bearing. SST 09316−12010, 09316 −60011 (09316−00011)
14. INSTALL FRONT DRIVE GEAR PIECE
Using SST and a press, install the front drive gear piece. SST 09316−12010, 09316 −60011 (09316−00011)
15. INSTALL SNAP RING
(a) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)MarkThickness mm (in.)
A2.00 (0.0787)G2.60 (0.1024)
B2.10 (0.0827)H2.70 (0.1063)
C2.20 (0.0866)J2.80 (0.1 102)
D2.30 (0.0906)K1.80 (0.0709)
E2.40 (0.0945)L1.90 (0.0748)
F2.50 (0.0984)−−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010