1996 TOYOTA LAND CRUISER Pump

PP30K−03
−
PREPARATION STARTING
PP−23
72
Author: Date:
1996 LAND CRUISER (RM451U)
STARTING
SST (Special Service Tools)
09286−46011Injection Pump Spline Shaft
PullerArmature bearing
09810−38140Starter Magnet Switch Nut Wrench
14Terminal nut
09820−00030Alternator Rear Bearing ReplacerArmature rear bearing
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP30N−01
PP−26
−
PREPARATION CHARGING
75
Author: Date:
1996 LAND CRUISER (RM451U)
CHARGING
SST (Special Service Tools)
09285−76010Injection Pump Camshaft Bearing
Cone ReplacerRotor rear bearing cover
09286−46011Injection Pump Spline Shaft
PullerRectifier end frame
09820−00021Alternator Rear Bearing Puller
09820−00030Alternator Rear Bearing Replacer
09820−63010Alternator Pulley Set Nut Wrench
Set
09950−60010Replacer Set
(09951−00260)Replacer 26Rotor front bearing
(09951−00500)Replacer 50Rotor front bearing
(09952−06010)AdapterRotor front bearing
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KM−01
PP−56
−
PREPARATION STEERING
105
Author: Date:
1996 LAND CRUISER (RM451U)
STEERING
SST (Special Service Tools)
09527−10011Rear Axle Shaft Bearing RemoverPS vane pump
09610−55012Pitman Arm PullerSteering linkage
09611−22012Tie Rod End PullerSteering linkage
09616−00011Steering Worm Bearing Adjusting
SocketPS gear
09628−62011Ball Joint PullerSteering linkage
09630−00014Power Steering Gear Housing
Overhaul Tool Set
(09631−00051)No.3 WrenchPS gear
(09631−00121)Teflon Ring FormerPS gear
(09631−00142)Overhaul StandPS gear
09631−10030Oil Seal RemoverPS vane pump
09631−22020Power Steering Hose Nut
14 x 17 mm Wrench SetPS gear
09640−10010Power Steering Pressure Gauge
Set
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KL−01
−
PREPARATION STEERING
PP−59
1996 LAND CRUISER (RM451U)
RECOMMENDED TOOLS
09025−00010Torque Wrench (30 kgf −cm)PS vane pump
PS gear
09042−00010Torx Socket T30 .Tilt steering column
09904−00010Expander Set .
(09904−00050)No. 4 Claw
09905−00012Snap Ring No.1 Expander .
09905−00013Snap Ring Pliers .
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YM−01
PP−60
−
PREPARATION STEERING
1996 LAND CRUISER (RM451U)
EQUIPMENT
Caliper gaugePS vane pump
CalipersPS vane pump
Dial indicatorPS gear
Feeler gaugePS vane pump
MicrometerPS vane pump
Torque wrench
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR06R−01
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
PR−5
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page PR−3 ).
HINT:
After installation, pump MP grease into each fitting with a grease gun until the grease begins to\
flow around
the oil seal.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI1654
Fulcrum Length
30 cm
SST
−
SFI SFI SYSTEM
SF−3
631
Author: Date:
1996 LAND CRUISER (RM451U)
8. FUEL SYSTEM
(a) When disconnecting the high fuel pressure line, a large
amount of gasoline will spill out, so observe the following
procedures:
(1) Disconnect the fuel pump connector.
(2) Start the engine. After the engine has stopped onits own, turn off the ignition switch.
(3) Put a container under the connection.
(4) Slowly loosen the connection.
(5) Disconnect the connection.
(6) Plug the connection with 2 rubber plugs.
(7) Reconnect the fuel pump connector.
(b) When connecting the union bolt on the high pressure pipe
union, observe the following procedures:
(1) Always use a new gasket.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 29 N·m (300 kgf·cm, 21 ft·lbf)
(c) When connecting the flare nut on the high pressure pipe union, observe the following procedures:
(1) Apply a light coat of engine oil to the flare and tight-
en the flare nut by hand.
(2) Using SST, tighten the flare nut to the specified torque.
SST 09631−22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P09286
New O−ring
Grommet Injector
Delivery Pipe WRONG
CORRECT
P09401
Fuel Return Hose
SF−4
−
SFI SFI SYSTEM
632
Author: Date:
1996 LAND CRUISER (RM451U)
(d) Observe the following precautions when removing and
installing the injectors.
(1) Never reuse the O −ring.
(2) When placing a new O −ring on the injector, take
care not to damage it in any way.
(3) Coat a new O −ring with spindle oil or gasoline be-
fore installing −never use engine, gear or brake oil.
(e) Install the injector to the delivery pipe and intake manifold
as shown in the illustration.
(f) Check that there are no fuel leaks after doing mainte- nance anywhere on the fuel system.
(1) Remove the fuse cover on the instrument panel.
(2) Connect the TOYOTA hand− held tester to the
DLC3.
(3) Turn the ignition switch ON and TOYOTA hand −
held tester main switch ON.
NOTICE:
Do not start the engine. (4) Select the active test mode on the TOYOTA hand−held tester.
(5) Please refer to the TOYOTA hand −held tester oper-
ator ’s manual for further details.
If you have no T OYOTA hand−held tester, connect the positive
(+) and negative ( −) leads from the battery to the fuel pump con-
nector (See page SF−14 ).
(6) Pinch the fuel return hose. The pressure in the high
pressure line will rise to approx. 392 kPa (4 kgf/cm
2,
57 psi). In this state, check to see that there are no
leaks from any part of the fuel system.
NOTICE:
Always pinch the hose. Avoid bending as it may cause the
hose to crack.
(7) Turn the ignition switch to LOCK.
(8) Disconnect the TOYOTA hand −held tester from the
DLC3.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010