1996 TOYOTA LAND CRUISER brake light

W01184
BR−BGR−R
31 6 15
13
Ts
Ts
DLC1 ABS ECU
12 V
E1IH1 A12
EC
GR−R
F00007
Ts
DLC1
E1
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−235
1996 LAND CRUISER (RM451U)
Ts Terminal Circuit
CIRCUIT DESCRIPTION
The sensor check circuit detects abnormalities in the speed sensor signal which cannot be detecte\
d with
the DTC check. Connecting terminals Ts and E
1 of the DLC1 in the engine compartment starts the check.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminals Ts and E1 of DLC1.
CHECK:
(a) Turn the ignition switch ON.
(b) Measure the voltage between terminals Ts and E
1 of the
DLC1.
OK:
Voltage: 10 − 14 V
OK If ABS warning light does not blink even after Ts and E
1 are connected, ECU may be defective.
NG
DI5MN−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O5−01
CRUISE CONTROL SYSTEM Check SheetInspector ’s name:
Customer ’s Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading
/ / km
Mile
Condition of
Problem Occurrence
Date of Problem
How Often does
Occurrence
Problem Occur?
Vehicle Speed when
Problem Occurred / /
Continuous Intermittent ( Times a day)
km
Mile
Brought in
Auto cancel
occurs Driving condition  City driving  Freeway  Up hill  Down hill
 After cancel occurred, did the driver activate cruise control again?
 Yes  No
 Cancel does not
occur 
With brake ON
 Except D position shift  At 40 km/h (25 mph) or less
 When control SW turns to CANCEL position
 Cruise control
malfunction 
Slip to acceleration side
 Slip to deceleration side
 Hunting occurs
 O/D cut off does not occur
 O/D does not return
 Switch
malfunction 
SET  ACCEL  COAST  RESUME  CANCEL
 Remains ON  Does not light up  Blinking
Symptoms
DTC Check
1st Time2nd Time

Normal Code  Malfunction Code (Code )
 Normal Code  Malfunction Code (Code )

Cruise MAIN
indicator light
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−285
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O5−01
CRUISE CONTROL SYSTEM Check SheetInspector ’s name:
Customer ’s Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading
/ / km
Mile
Condition of
Problem Occurrence
Date of Problem
How Often does
Occurrence
Problem Occur?
Vehicle Speed when
Problem Occurred / /
Continuous Intermittent ( Times a day)
km
Mile
Brought in
Auto cancel
occurs Driving condition  City driving  Freeway  Up hill  Down hill
 After cancel occurred, did the driver activate cruise control again?
 Yes  No
 Cancel does not
occur 
With brake ON
 Except D position shift  At 40 km/h (25 mph) or less
 When control SW turns to CANCEL position
 Cruise control
malfunction 
Slip to acceleration side
 Slip to deceleration side
 Hunting occurs
 O/D cut off does not occur
 O/D does not return
 Switch
malfunction 
SET  ACCEL  COAST  RESUME  CANCEL
 Remains ON  Does not light up  Blinking
Symptoms
DTC Check
1st Time2nd Time

Normal Code  Malfunction Code (Code )
 Normal Code  Malfunction Code (Code )

Cruise MAIN
indicator light
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−285
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14305
(1)
(1) (2)
No.
Operation Method CRUISE MAIN Indicator Light
Blinking Pattern Diagnosis
1 Turn SET/COAST switch ON
2 Turn RES/ACC switch ON
3 Turn CANCEL switch ON
Turn stop light switch ON
Depress brake pedal
Turn PNP switch OFF
(Shift to except D position)
4 Drive at about 40 km/h
(25 mph)or higher
Drive at about 40 km/h
(25 mph) or below
Light
ON
OFF
Light ON
OFF
Light ON
OFF Switch ON
Switch OFF
LightON
OFF Switch OFF
Switch ONSET/COAST switch circuit
is normal
RES/ACC switch circuit
is normal
CANCEL switch circuit
is normalStop light switch circuit
is normal
PNP switch circuit is
normal
Vehicle Speed Sensor is
normal
Light ON
OFF
Light
ON
OFF
1sec.
0.25 sec. 0.25 sec.
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-290
1996 LAND CRUISER (RM451U)
5. INPUT SIGNAL CHECK
HINT:
(1) For check No.1 - No.3

Turn ignition switch ON.
(2) For check No.4

Jack up the vehicle.

Start the engine.

Shift to D position.
(a) Press the control switch to SET/COAST or RES/ACC position and hold it down or hold it up º1º.
(b) Push the main switch ON º2º.
(c) Check that the CRUISE MAIN indicator light blinks twice or 3 times repeatedly after 3 seconds.
(d) Turn the SET/COAST or RES/ACC switch OFF.
(e) Operate each switch as listed in the table below.
(f) Read the blinking pattern of the CRUISE MAIN indicator light.
(g) After performing the check, turn the main switch OFF.
HINT:
When 2 or more signals are input to the ECU, the lowest num-
bered code will be displayed first.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OA−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−295
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
SET not occourring or CANCEL occurring.
(DTC is Normal)
1. Main Switch Circuit (Cruise control switch)
2. Vehicle Speed Sensor
3. Control Switch Circuit (Cruise control switch)
4. Stop Light Switch Circuit
5. Park/Neutral Position Switch Circuit
6. Actuator Motor Circuit
7. Cruise Control Cable
8. Cruise Control ECUDI−330
DI−306
DI−311
DI−314
DI−322
DI−296
DI−336 IN−28
SET not occurring or CANCEL occurring.
(DTC does not output)1. ECU Power Source Circuit
2. Cruise Control ECUDI−325IN−28
Actual vehicle speed deviates above or below the set speed.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Electronically Controlled Transmission Communication
Circuit
4. Actuator Motor Circuit
5. Idle Signal Circuit (main throttle position sensor)
6. Cruise Control ECUDI−336
DI−310
DI−319
DI−296
DI−316IN−28
Gear shifting frequent between 3rd O/D when driving on uphill
road. (Hurting)1. Electronically Controlled Transmission Communication
Circuit
2. Cruise Control ECUDI−319
IN−28
Cruise control not cancelled, even when brake pedal is de-
pressed.
1. Cruise Control Cable
2. Stop Light Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−314
DI−296IN−28
Cruise control not cancelled, even when transmission is shifted to
”N” postion.
1. Cruise Control Cable
2. Park/Neutral Position Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−322
DI−296IN−28
Control switch does not operate.
(SET/COAST, A CC/RES, CANCEL not possible)
1. Cruise Control Cable
2. Control Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−311
DI−296 IN−28
SET possible at 40 km/h (25 mph) or less, or CANCEL does not
operate at 40 km/h (25 mph) or less.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−310
DI−296IN−28
Poor response is ACCEL and RESUME modes.
1. Cruise Control Cable
2. Electronically Controlled Transmission Communication
Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI−336
DI−319
DI−296IN−28
O/D does not RESUME, even though the road is not uphill.
1. Electronically Controlled Transmission Communication
Circuit
2. Cruise Control ECUDI−319
IN−28
DTC memory is erased.1. Back− up Power Source Circuit
2. Cruise Control ECUDI−328 IN−28
DTC is not output, or is output when is should not be.1. Diagnosis Circuit
2. Cruise Control ECUDI−319IN−28
Cruise MAIN indicator light remains ON or fall to light up.1. Cruise MAIN Indicator Light Switch CircuitDI−332
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00489
Cruise Control ECUL
L−
W−B
1
5
4 3
2 R
1026
C4 Stop Light Switch
4
R−G
Cruise
Control Actuator
C17
C17
C17
C4S13
S13 S13
S13
G−O G−WF11F11
1
2
STOP
Instrument Panel Fuse Block
W
EA3
W
3
1
F8
Battery Fusible Link
FL MAIN
STP−
DI−298
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
DTC 12 Actuator Magnetic Clutch Circuit
CIRCUIT DESCRIPTION
This circuit turns on the magnetic clutch inside the actuator during cruise \
control operation according to the
signal from the ECU. If a malfunction occurs in the actuator or speed sensor, etc. during cruise control opera-
tion, the rotor shaft between the motor and control plate is released.
When the brake pedal is depressed, the stop light switch turns on, supplying electrical power to the stop light.
Power supply to the magnetic clutch is mechanically cut and the magnetic clut\
ch is turned OFF.
When driving downhill, if the vehicle speed exceeds the set speed by 15 km/h\
(9 mph), the ECU turns the
safety magnet clutch OFF. If the vehicle speed later drops to within 10 km/h (6 mph) above the\
set speed,
then cruise control at the set speed is resumed.
DTC No.Detection ItemTrouble Area
12 Short in actuator magnetic clutch circuit.
 Open (0.8 sec.) in actuator magnetic clutch circuit.
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
WIRING DIAGRAM
DI5OC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N18670
Instrument Panel Fuse Block
STOP Fuse
I00133
1
2
43
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−299
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check STOP fuse.
PREPARATION:
(a) Turn ignition switch OFF.
(b) Remove the STOP fuse from instrument panel fuse block.
CHECK:
Check fuse continuity.
OK:
There is continuity.
NG Replace STOP fuse.
OK
2 Check stop light switch.
PREPARATION:
Disconnect the stop light switch connector.
CHECK:
Check continuity between terminals.
Switch positionContinuity
Switch pin free
(Brake pedal depressed)1 − 2
Switch pin pushed in
(Brake pedal released)3 − 4
NG Replace stop light switch.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Stop Light
switch ON
Light ON
OFF SW OFF
SW ON
DI−314
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Stop Light Switch Circuit
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light switch sends a signal to th\
e ECU. When the ECU receives
this signal, it cancels the cruise control.
A fail− safe function is provided so that the cancel functions normally , even if there is a malfunction in the stop
light signal circuit.
The cancel conditions are: Battery positive voltage at terminal STP −
When the brake is on, battery positive voltage normally applies through the S\
TOP fuse and stop light switch
to terminal STP− of the ECU, and the ECU turns the cruise control off.
If the harness connected to terminal STP − has an open circuit, terminal STP − will have battery positive volt-
age and the cruise control will be turned off.
Also, when the brake is on, the magnetic clutch circuit is cut mechanically \
by the stop light switch, turning
the cruise control off (See page DI−298 for operation of the magnetic clutch).
WIRING DIAGRAM
See page DI−298 .
INSPECTION PROCEDURE
1 Check operation of stop light.
CHECK:
Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.
NG Check stop light system (See page BE−24 ).
OK
2 Input signal check.
CHECK:
(a) See input signal check on DI−286.
(b) Check the indicator light when the brake pedal is de-
pressed.
OK:
The indicator light goes off when the brake pedal is
depressed.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
DI5OI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010