1996 TOYOTA LAND CRUISER brake light

N09348
Interface BoxHarness VehicleTOYOTA
Tester
Hand
−held
TOYOTA Break −out− box
F00007
DLC1
Ts Tc
E
1
BR3904
0.25 sec. 0.25 sec.
ON
OFF
DI−192
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(d) Using TOYOTA break −out− box and TOYOTA hand− held
tester, measure the ECU terminal values.
(1) Hook up the T OYOTA hand−held tester and TOYO-
TA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the prompts on the tester screen.
HINT:
TOYOTA hand −held tester has a ”Snapshot ” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break
out−box operators manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal. (1) Conform that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(7) Stop the vehicle.
(8) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(9) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−190 .
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR3893
Malfunction Code (Example Code 72, 76)
72 6
7
ON
OFF
0.5 sec.
0.5 sec.
0.5 sec.
0.5 sec. 1.5 sec.
2.5 sec. 4 sec.
Repeat
F00007
E1
Ts
DLC1
R05599
0.13 sec.
0.13 sec.
3 sec.
ON
OFF
R05037
860 
30 mm
33.86  1.18 in.
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−193
1996 LAND CRUISER (RM451U)
(10) After doing the check, disconnect terminals Ts and
E
1, Tc and E1 of the DLC1, and turn the ignition
switch OFF.
(b) Deceleration sensor detection point check. (1) Confirm that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Jack up the rear side of the vehicle slowly.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (7) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor. (8) Jack down the vehicle slowly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05038
780  30 mm
30.71  1.18 in.
BR1865
0.13 sec.
0.13 sec.
ON
OFF
R05596
0.13 sec.
Braking
0.13 sec.
R05597
0.13 sec. 0.13 sec.
Braking
DI−194
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(9) Jack up the front side of the vehicle slowly, as
shown.
HINT:
When measuring the height, measure at the center of the lower
body of the vehicle. (10) Check that the warning light blinks.
If the warning light turns on, inspect the deceleration sensor
installation. If the sensor installation is OK, replace the decel-
eration sensor.
(11) Jack down the vehicle slowly.
(c) Deceleration sensor operation check. (1) Drive the vehicle straight ahead at about 20 km/h
(12.4 mph) or more, lightly depress the brake pedal.
(2) Check that there is no change in the warning light pattern.
(3) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
moderately.
(4) Check that the warning light turns on while braking.
(5) Drive the vehicle straight ahead at about 20 km/h (12.4 mph) or more, and depress the brake pedal
strongly.
(6) Check that the warning light pattern changes while braking, as shown.
If the operation is not as specified, inspect the deceleration sen-
sor installation. If the sensor installation is OK, replace the de-
celeration sensor. (7) Stop the vehicle and turn the ignition switch OFF.
(8) Remove SST from the terminals Ts and E
1 of the
DLC1.
SST 09843−18020
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5LX−02
W03004
Rear Speed Sensor
Rear Speed Sensor Rotor
Front Speed Sensor
Stop Light Switch
ABS Warning Light
Deceleration Sensor
DLC1
ABS ECU
ABS Actuator
ABS Relay
Front Speed Sensor Rotor
DI−198
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5LZ−03
DI−200
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the DTC check but the problem still o\
ccurs, check the circuits for each
problem symptom in the order given in the table below and proceed to the releva\
nt troubleshooting page.
SymptomsSuspected AreaSee page
ABS does not operate
Only when 1 − 4 are all normal and the problem is still occurring, replace the ABS
ECU
2. Check the DTC reconfirming that the normal code is output
3. IG power source circuit
4. Speed sensor circuit
5. Check the ABS actuator with a checker
If abnormal, check the hydraulic circuit for leakage (See page DI−237)
DI−190
DI−215
DI−210
BR−53
ABS does not operate effi-
ciently
Only when 1 − 4 are all normal and the problem is still occurring, replace the ABS
ECU
1. Check the DTC reconfirming that the normal code is output
2. Speed sensor circuit
3. Stop light switch circuit
4. Check the ABS actuator with a checker
If abnormal, check the hydraulic circuit for leakage (See page DI−237)
DI−190
DI−210
DI−228
BR−53
ABS warning light abnormal1. ABS warning light circuit
2. ABS ECUDI−230 −
DTC check cannot be done
Only when 1 and 2 are all normal and the problem is still occurring, rep\
lace the
ABS ECU
1. ABS warning light circuit
2. Tc terminal circuit
DI−230
DI−233
Speed sensor signal check
cannot be done1. Ts terminal circuit
2. ABS ECUDI−235−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02196
BF
6
ECU−IG Y
Junction
Connector ABS ECU
W−B Y−B
4
2 3
1
Deceleration
Sensor
A12
ABS ECU
GS1
GS2 GST
A22
3
B−W
Y
B−W
B−W
A22A22 A22
A22
A12
A12
12
10
12 13 14
15
Y−RY−R
Y−B
B
B
B 12 V
12 V
ID3
ID3
ID3
ID2
3
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−219
1996 LAND CRUISER (RM451U)
DTC 44 Deceleration Sensor Circuit
CIRCUIT DESCRIPTION
This sensor detects deceleration on the vehicle. The sensor signal is used in ABS control. If the sensor func-
tions abnormally, the ABS warning light comes on but the ABS still operates.
DTC No.DTC Detecting ConditionTrouble Area
44
Either of the following 1 or 2 is detected:
1. An open or short is detected in circuit GS1 or GS2 for
1sec.
2. After the ignition is turned ON, the test signal is output by GST
During this time, a trouble signal is detected for 0.5 sec.
Deceleration sensor
 Open or short in deceleration sensor circuit
WIRING DIAGRAM
DI5M8−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02197
Ignition
Switch
Battery
AM1
F61
B−L 2 2
3
4
W
2 12
AM1R/B No. 2
2
BB
EA2
6
B−Y
42
GAUGEY A
A
J1
Junction
Connector
CENTER DIFF. LOCK
Indicator Light Y
C10
P−B
P−B
P−B
C11
5
A1319
EXI
CENTER
DIFF. LOCK
DETECTION
Switch ABS ECU
2
1
3
R/B No. 2
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−221
1996 LAND CRUISER (RM451U)
DTC 48 Center Differential Lock Circuit
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
48Open or short circuit in center differential lock circuit
Center differential is lockingCenter differential lock
 Center differential lock circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check the center differential is free (Transfer is in H position).
NG Repair the center differential lock system.
OK
DI5M9−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−222
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
2 Is DTC output?
Check DTC on page DI−190 .
NO Normal.
YES
3 Check that CENTER DIFF. LOCK indicator light does not go off.
NO Go to step 6.
YES
4 Check that bulb for CENTER DIFF. LOCK indicator light is not burnt out.
YES Replace indicator light.
NO
5 Check for open in harness and connector between battery and CENTER DIFF. LOCK indicator light, and CENTER DIFF. LOCK indicator light and ABS ECU (See
page IN−28 ).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010