1996 TOYOTA LAND CRUISER Ect

BR1CU−03
−
BRAKE FRONT BRAKE CALIPER
BR−25
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 mounting bolts and caliper. Torque: 123 N·m (1,250 kgf·cm, 90 ft·lbf)
3. REMOVE THESE PARTS:
Clip
2 pins
Anti−rattle spring
2 pads
4 anti−squeal shims
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CX−03
BR0251
−
BRAKE FRONT BRAKE CALIPER
BR−27
1996 LAND CRUISER (RM451U)
INSPECTION
1. MEASURE PAD LINING THICKNESS
Using a ruler, measure the pad lining thickness.
Standard thickness: 9.5 mm (0.374 in.)
Minimum thickness: 1.0 mm (0.039 in.)
Replace the pad if the thickness is less than the minimum (the
1.0 mm slit is no longer visible), or if it shows signs of uneven
wear.
2. MEASURE DISC THICKNESS
Using a micrometer, measure the disc thickness. Standard thickness: 32.0 mm (1.260 in.)
Minimum thickness: 30.0 mm (1.181 in.)
If the disc is scored or worn, or if its thickness is less than the
minimum, repair or replace the disc.
3. MEASURE DISC RUNOUT
Using a dial indicator, measure the disc runout at a position 10
mm (0.39 in.) from the outside edge. Maximum disc runout: 0.15 mm (0.0059 in.)
If the runout is greater than the maximum, replace the disc or
grind it on a ”On−Car” brake lathe.
HINT:
Before measuring the runout, confirm that the front hub bearing
play is within the specification.
4. IF NECESSARY, REPLACE DISC
(a) Remove the front axle hub (See page SA−7).
(b) Remove the disc from the axle hub.
(c) Install a new disc and torque the bolts. Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
(d) Install the axle hub and adjust the front bearing preload (See page SA−9 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D0−03
−
BRAKE REAR BRAKE PAD
BR−31
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE REAR WHEEL
Remove the wheel and temporarily fasten the disc with the hub
nuts.
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace pads if the thickness is not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE BRAKE CALIPER
(a) Remove the sliding main pin and sliding sub pin.
(b) Remove the caliper and suspend it so the hose is not stretched.
HINT:
Do not disconnect the flexible hose.
4. REMOVE THESE PARTS:
(a) 2 brake pads
(b) Anti−squeal shim
(c) 4 pad support plates
(d) 2 pad wear indicator plates
NOTICE:
The pad support plates can be used again provided that
they have sufficient rebound, no deformation, cracks or
wear, and have had all rust, dirt and foreign particles
cleaned off.
5. CHECK DISC THICKNESS AND RUNOUT (See page BR−36 )
6. INSTALL PAD SUPPORT PLATES
7. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti −squeal shim and wear
indicator plates must be replaced together with the pads.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D2−01
BR−34
−
BRAKE REAR BRAKE CALIPER
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper, then disconnect the flexible hose from the cali-
per.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 sliding pins and caliper. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
3. REMOVE THESE PARTS:
(a) 2 pads with anti −squeal shim
(b) 4 pad support plates
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D5−03
BR−36
−
BRAKE REAR BRAKE CALIPER
1996 LAND CRUISER (RM451U)
INSPECTION
1. MEASURE PAD LINING THICKNESS (See step 1. on page BR−27)
Standard thickness: 10.0 mm (0.394 in.)
Minimum thickness: 1.0 mm (0.039 in.)
2. MEASURE DISC THICKNESS (See page BR−27 )
Standard thickness: 18.0 mm (0.709 in.)
Minimum thickness: 16.0 mm (0.630 in.)
3. MEASURE DISC RUNOUT (See page BR−27 )
Maximum disc runout: 0.15 mm (0.0059 in.)
If the runout is greater than the maximum, adjust the disc runout
or grind it on a ”On−Car” brake lathe.
4. IF NECESSARY, REPLACE DISC
(a) Remove the torque plate..
(b) Remove the hub nuts of the temporarily installed disc and
pull off the disc.
(c) Install a new disc and and loosely install the hub nuts.
(d) Install the torque plate and tighten the mounting bolts. Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE PARKING BRAKE
BR−41
1996 LAND CRUISER (RM451U)
7. REMOVE REAR SHOE, ADJUSTER AND TENSION
SPRING
(a) Slide out the rear shoe, and remove the rear shoe and ad-
juster.
(b) Remove the 2 shoe hold −down spring cups, spring and
pin.
(c) Remove the lower side tension spring.
8. REMOVE FRONT SHOE
(a) Slide out the front shoe.
(b) Remove the shoe 2 hold −down spring cups, springs and
pin.
(c) Disconnect the parking brake cable from the parking
brake shoe lever.
9. IF NECESSARY, REMOVE AND DISASSEMBLE PARKING BRAKE BELLCRANK ASSEMBLY
(a) Using a screwdriver, remove the C −washer.
(b) Remove the pin and disconnect the parking brake cable No.2 from the bellcrank.
(c) Remove the clip.
(d) Remove the pin and clip, then disconnect the parking
brake cable.
(e) Remove the 2 tension springs.
(f) Remove the 2 bolts and parking brake bellcrank assem- bly.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(g) Remove the boot from parking brake bellcrank bracket.
(h) Using a screwdriver, remove the C −washer and pin.
(i) Remove the parking brake bellcrank from the bell crank bracket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D9−02
BR0897
BR0828
R00343Clearance Shim
BR−42
−
BRAKE PARKING BRAKE
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT DISASSEMBLED PARTS
Inspect the disassembled parts for wear, rust or damage.
2. MEASURE BRAKE SHOE LINING THICKNESS
Using a ruler, measure the thickness of the shoe lining. Standard thickness: 4.0 mm (0.157 in.)
Minimum thickness: 1.0 mm (0.039 in.)
If the lining thickness is at the minimum thickness or less, or if
there is extremely uneven wear, replace the brake shoe.
3. MEASURE BRAKE DISC INSIDE DIAMETER
Using a vernier calipers, measure the inside diameter of the
disc. Standard inside diameter: 230 mm (9.06 in.)
Maximum inside diameter: 231 mm (9.09 in.)
Replace the disc if the inside diameter is at the maximum value
or more. Replace the disc or grind it with a lathe if the disc is
scored or is worn unevenly.
4. INSPECT PARKING BRAKE LINING AND DISC FOR PROPER CONTACT
Apply chalk to the inside surface of the disc, then grind down
the brake shoe lining to fit. If the contact between the disc and
the brake shoe lining is improper, repair it using a brake shoe
grinder or replace the brake shoe assembly.
5. MEASURE CLEARANCE BETWEEN PARKING BRAKE SHOE AND LEVER
Using a feeler gauge, measure the clearance.
Standard clearance: Less than 0.35 mm (0.0138 in.)
If the clearance is not within the specification, replace the shim
with one of the correct size.
Shim ThicknessShim Thickness
0.3 mm (0.012 in.)0.9 mm (0.035 in.)
0.6 mm (0.024 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE PARKING BRAKE
BR−43
1996 LAND CRUISER (RM451U)
6. IF NECESSARY, REPLACE SHIM
(a) Using a screwdriver, remove the C −washer.
(b) Remove the park ing brake shoe lever, and install the cor-
rect size shim.
(c) Using needle −nose pliers, install the parking brake shoe
lever with a new C −washer.
(d) Remeasure the clearance.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010