1996 TOYOTA LAND CRUISER low oil pressure

SS1EC−02
SS−30
−
SERVICE SPECIFICATIONS SUSPENSION AND AXLE
153
Author: Date:
1996 LAND CRUISER (RM451U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflation
pressureTire size
P275/70R 16
220 kPa (2.2 kgf/cm2, 32 psi)
Follow spring and
bumper stopper
clearanceFollow spring clearance (Front)
Bumper stopper clearance (Rear)36 mm (1.42 in.)
104 mm (4.09 in.)
Front wheel align-
mentCamber Left−right error1°00’ ± 45’
45’ or less
Caster Left−right error3°00’ ± 60’
45’ or less
Steering axis inclination13 °00’ ± 45’
To e −in (Total) Inspection STD
Adjustment STD0.2 ° ± 0.2° (2 ± 2 mm, 0.08 ± 0.08 in.)
0.2 ° ± 0.1° (2 ± 1 mm, 0.08 ± 0.04 in.)
Wheel angle (Max.) Inside wheel
Outside wheel32 °00’ − 35°00’
31 °00’
Tire and wheelTire runout
Wheel balance (Unbalance after adjustment)
Wheel bearing preload (at starting) Front
(Rotating load at hub bolt) Rear3.0 mm (0.118 in.) or less
13.0 g (0.029 lb) or less
28 − 56 N (2.9 − 5.7 kgf, 6.4 − 12.6 lbf)
26 − 57 N (2.6 − 5.8 kgf, 5.7 − 12.8 lbf)
Front axleSteering knuckle bearing preload
(Rotating load at knuckle end, before installing dust seal)
25 − 44 N (2.5 − 4.5 kgf, 5.5 − 9.9 lbf)
Front dif ferentialDrive pinion preload (at starting) New bearing
Reused bearing0.9 − 1.6 N·m (10 − 16 kgf·cm, 8.7 − 13.9 in.·lbf)
0.5 − 0.8 N·m (5 − 8 kgf·cm, 4.3 − 6.9 in.·lbf)
Total preload (at starting)Drive pinion preload plus
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
Drive pinion to ring gear backlash0.13 − 0.18 mm (0.0051 − 0.0071 in.)
Pinion gear to side gear backlash0.05 − 0.20 mm (0.0020 − 0.0079 in.)
Ring gear runout Max.0.10 mm (0.0039 in.)
Companion flange runoutMax. Radial
Lateral0.10 mm (0.0039 in.)
0.10 mm (0.0039 in.)
Oil seal drive in depth1.0 mm (0.039 in.)
Side gear thrust washer thickness w/o Differntial lock
w/ Differntial lock1.6 mm (0.063 in.)
1.7 mm (0.067 in.)
1.8 mm (0.071 in.)
0.9 mm (0.035 in.)
1.0 mm (0.039 in.)
1.1 mm (0.043 in.)
1.2 mm (0.047 in.)
1.3 mm (0.051 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EG−02
−
SERVICE SPECIFICATIONS STEERING
SS−37
160
Author: Date:
1996 LAND CRUISER (RM451U)
STEERING
SERVICE DATA
ON−VEHICLE INSPECTION
Steering wheel freeplay Maximum40 mm (1.57 in.)
Fluid level riseMaximumBelow 5 mm (020 in.)
Fluid pressure at idle speed with valve closed Minimum9,316 kPa (95 kgf/cm2, 1,351 psi)
Steering effort at idle speedMaximum8.3 N·m (85 kgf·cm, 73 in.·lbf)
TILT STEERING COLUMN
Pawl stopper alignment mark 1 or A
2 or B
3 or C
4 or D 5 or E12.65 − 12.75 mm (0.4980 − 0.5020 in.)
12.55 − 12.65 mm (0.4941 − 0.4980 in.)
12.45 − 12.55 mm (0.4902 − 0.4941 in.)
12.35 − 12.45 mm (0.4962 − 0.4902 in.)
12.25 − 12.35 mm (0.4823 − 0.4862 in.)
PS VANE PUMP
Oil clearance between pump shaft and bushing STD
Maximum0.03 − 0.05 mm (0.0012 − 0.0020 in.)
0.07 mm (0.0028 in.)
Vane plate height Minimum8.6 mm (0.339 in.)
Vane plate thickness Minimum1.397 mm (0.05500 in.)
Vane plate length Minimum14.991 mm (0.59016 in.)
Vane plate and pump rotor groove clearanceMaximum0.033 mm (0.00130 in.)
Vane plate lengthPump rotor mark
None1
2
Cam ring mark
2
3
4
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
Spring free length STD35 − 37 mm (1.38 − 1.46 in.)
Vane pump rotaing torque Maximum0.3 N·m (2.8 kgf·cm, 2.4 in.·lbf)
PS GEAR
Worm gear valve body ball clearanceMaximum0.15 mm (0.059 in.)
Cross shaft adjusting screw thrust clearance STD0.03 − 0.05 mm (0.0012 − 0.0020 in.)
Worm gear preload0.3 − 0.5 N·m (3 − 5.5 kgf·cm, 2.6 − 4.8 in.·lbf)
Total preload0.74 − 1.08 N·m (7.5 − 11.0 kgf·cm, 6.5 − 9.6 in.·lbf)
STEERING LINKAGE
Tie rod length Approximately1.207 mm (47.51 in.)
Relay rod lengthApproximately1.085 mm (42.72 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EJ−02
SS−40
−
SERVICE SPECIFICATIONS BODY ELECTRICAL
163
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL
SERVICE DATA
TURN SIGNAL FLASHER
Flashes/Minute60 − 120
SPEEDOMETER (USING A SPEEDOMETER)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
TACHOMETER (ON− VEHICLE) DC 13.5 V 25°C (77° F)
Standard indication (RPM)Allowable range (RPM)
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
FUEL RECEIVER GAUGE
A − B85.5 − 105.5 Ω
A − C126 − 150 Ω
B − C90 − 110 Ω
FUEL SENDER GAUGE
Float position F: Approx. 15 mm ((0.59 in.)Approx. 3 Ω
Float position E: Approx. 200 (7.87 in.)Approx. 110 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE
A − B71 − 79 Ω
A − C117 − 141 Ω
B − C185 − 215 Ω
OIL PRESSURE RECEIVER GAUGE
Resistance40 − 48 Ω
CRUISE CONTROL SWITCH
Switch position OFFNo continuity
Switch position RESUME/ACCELApprox. 68 Ω
Switch position SET/COASTApprox. 198 Ω
Switch position CANCELApprox. 418 Ω
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2 kΩ
2 − 3Approx. 0.5 − 1.7 kΩ
Actuator control arm free play0 mm (0 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010