1996 TOYOTA LAND CRUISER ignition

BE−8
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Sliding roof system operates abnormally.
1. Limit Switch
2. Sliding Roof Control Switch
3. Sliding Roof Control RelayBE−58
BE−58
BE−58
Sliding roof system stops operation half way.
1. Sliding Roof Control Relay
2. Sliding Roof Limit Switch
3. Sliding Roof Control Switch
4. Sliding Roof Motor
(Stones to foreign material trapped in motor assembly)BE−58
BE−58
BE−58
BE−58
”Key−off sliding roof” operation does not operate.
1. POWER Fuse (I/P F/B)
2. Door Lock Control Relay
3. GAUGE Fuse (I/P F/B)
4. Ignition Switch
5. Door Courtesy Switch
6. Wire Harness−
BE−51 −
BE−11
BE−21
−
POWER MIRROR SYSTEM
SymptomSuspect AreaSee page
Power mirror system does not operate.
1. CIG Fuse (I/P J/B)
2. Mirror Control Switch
3. Mirror Motor
4. Wire Harness−
BE−69
BE−69 −
Power mirror operate abnormally.
1. Mirror Control Switch
2. Mirror Motor
3. Wire HarnessBE−69
BE−69−
POWER SEAT CONTROL SYSTEM
SymptomSuspect AreaSee page
Power seat does not operate.
1. POWER Fuse (I/P F/B)
2. Power Seat Switch
3. Wire Harness−
BE−62 −
”Sliding operation” does not operate.
1. Slide Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Reclining operation” does not operate.
1. Reclining Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Rear vertical operation” does not operate.
1. Rear Vertical Motor
2. Power Seat Switch
3. Wire HarnessBE−62
BE−62−
”Lumber support operation” does not operate.
1. Lumber Support Motor
2. Lumber Support Switch
3. Wire HarnessBE−62
BE−62−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LV−01
BE−10−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1148
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LW−01
−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE−11
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK−No continuity
ACC7 − 9Continuity
ON3 − 4, 6 − 7 − 9Continuity
START2 − 3 − 4
6 − 9 − 10Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SWITCH CONTINUITY
ConditionTester connectionSpecified condition
SW OFF
(Key removed)−No continuity
SW ON (Key set)1 − 5Continuity
If continuity is not as specified, replace the switch.
3. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE−21 )
4. INSPECT SEAT BELT WARNING RELAY CIRCUIT
(See page BE−34 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL COMBINATION METER
BE−35
1996 LAND CRUISER (RM451U)
RPM (DC 13.5 V, 25 °C (77 ° F))
Standard indicationAllowable range
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
4. INSPECT VOLTMETER
ON−VEHICLE:
Compare the tester and voltmeter indications.
If error is excessive, replace the voltemeter.
5. INSPECT FUEL RECEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver gauge needle indicates EMPTY.
(c) Connect terminals 4 and 5 on the wire harness side con- nector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights up and the receiver gauge needle moves towards the full
side.
HINT:
Because of the silicon oil in the gauge, it will take a short time
for needle to stabilize.
If operation is not as specified, inspect the receiver gauge resis-
tance.
6. INSPECT FUEL RECEIVER GAUGE RESISTANCE
Between terminalsResistance (Ω )
A − B85.5 − 105.5
A − C126 − 150
B − C*90 − 11 0
*: Include voltmeter resistance
If resistance value is not as specified, replace the fuel receiver
gauge.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−36
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
7. INSPECT FUEL SENDER GAUGE OPERATION
(a) Connect a series of three 1.5 V dry cell batteries.
(b) Connect the positive (+) lead from the dry cell batteries to
terminal 4 through a 3.4 W test bulb and the negative ( −)
lead to terminal 5.
(c) Connect the positive (+) lead from the voltmeter to termi- nal 4 and the negative ( −) lead to terminal 5.
(d) Check that the voltage rises as the float is moved from the
full to empty position.
8. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between terminals 4 and 5.
Float position: mm (in.)Resistance (Ω )
F: Approx. 15.0 (0.591)Approx. 3.0
E: Approx. 200.0 (7.874)Approx. 110.0
If resistance value is not as specified, replace the sender
gauge.
9. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 5 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
10. INSPECT FUEL LEVEL WARNING SWITCH
(a) Apply battery positive voltage between terminals 1 and 5
through a 3.4 W test bulb, and check that the bulb lights
up.
HINT:
It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, and check that the bulb goes
out.
If operation is not as specified, replace the sender gauge.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Engine Coolant
Temperature
Gauge
Ignition Switch
Battery Sender
Gauge
Z06815
Engine
Coolant T emperature Gauge
Ignition
Switch Tester Bulb
(3.4 W)
Battery
BE1222
Oil Pressure Gauge
Ignition
Switch Sender
Gauge
Battery
−
BODY ELECTRICAL COMBINATION METER
BE−37
1996 LAND CRUISER (RM451U)
11. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge. Then re-
check the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
12. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (Ω )
A − B71 − 79
A − C117 − 141
B − C185 − 215
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the above order. This circuit include the
diode.
If resistance value is not as specified, replace the receiver
gauge.
13. INSPECT OIL PRESSURE RECEIVER GAUGE OP-
ERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates LOW.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE2570
ON
OFF
BE0044
BE1428
−
BODY ELECTRICAL COMBINATION METER
BE−39
1996 LAND CRUISER (RM451U)
18. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Check that there is no continuity between terminals with
the switch OFF (float up).
(b) Check that there is continuity between terminals with the switch ON (float down).
If operation is not as specified, replace the switch.
19. INSPECT OPEN DOOR WARNING LIGHT
(a) Disconnect the connector from the door courtesy switch and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, and check that the warning light lights up.
If the warning light does not light up, test the bulb.
20. INSPECT DOOR COURTESY SWITCH
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin re-
leased:opened door).
(b) Check that there is no continuity between terminal and
the switch body with the switch OFF (switch pin pushed
in:closed door).
If operation is not as specified, replace the switch.
21. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the seat belt warning relay.
(b) Ground terminal 9 on the wire harness side connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
22. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that there is continuity between terminals with the switch ON (belt unfastened).
(b) Check that there is no continuity between terminals with the switch OFF (belt fastened).
If operation is not as specified, replace the seat belt inner.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010