1996 TOYOTA LAND CRUISER ignition

A00157
ONECM
Engine Coolant
Temp. Sensor
5V
E2 E1
2
1
THW E2
THW
E5
E54
9
BE6653
FI7057
P24656
A00158
ON
Engine Coolant
Temp. Sensor ECM
5V
4
9 E2
E1
THW
BE6653
FI7054 E5
E5
DI−32
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Connect between terminals THW and E2 of ECM connec-
tor.
HINT:
Engine coolant temp. sensor connector is disconnected. Be-
fore checking, do a visual and contact pressure check for the
ECM connector (See page IN−28).
(c) Turn ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand −held tester.
OK:
Temperature value: 140° C (284°F) or more
OK Open in harness between terminals E2 or THW, repair or replace harness.
NG
Confirm good connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check for short in harness or ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Turn ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand−held tester.
OK:
Temperature value: − 40° C (− 40°F)
OK Replace engine coolant temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00159
ON
Engine Coolant
Temp. Sensor ECM
5V
E2 E1
E5 connector
THW
BE6653
FI7056
P19798
−
DIAGNOSTICS ENGINE
DI−33
1996 LAND CRUISER (RM451U)
5 Check for short in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Disconnect the E5 connector of ECM.
HINT:
Engine coolant temp. sensor connector is disconnected.
(c) Turn ignition switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA
hand −held tester.
OK:
Temperature value: − 40° C (− 40°F)
OK Repair or replace harness or connector.
NG
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00483
2
1 3 4R−G
G−B
G−W
BR−B
Throttle Position Sensor
* Closed Throttle
Position Switch
* E5 E5
E5 E5
10 1
11 9 VTA
E2 VCC
IDL 5V
E1 B+
P22422
ECM
FI7052
DI−36
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester and read the throttle
valve opening percentage.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3.
(c) Turn ignition switch ON and push the OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read the throttle valve opening percentage.
OK:
Throttle valveThrottle valve opening positionexpressed as percentage
Fully openApprox. 75 %
Fully closedApprox. 10 %
OK Check for intermittent problems (See page DI−3 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00160BE6653
P24657
ON1
−
DIAGNOSTICS ENGINE
DI−37
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal 1 of wire harness side connector and body
ground.
PREPARATION:
(a) Disconnect the throttle position sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal 1 of wire harness side con-
nector and body ground.
OK:
Voltage: 4.5 − 5.5 V
NG Go to step 5.
OK
3 Check throttle position sensor (See page SF−42).
NG Replace throttle position sensor.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00161
ON
BE6653
P24658
(+) (−)
VTA
E2
A00162
ON
VCC E2
(+) (−)
BE6653
P24659
DI−38
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check voltage between terminals VTA and E2 of ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals VTA and E2 of ECM.
OK:
Throttle valveVoltage
Fully closed0.3 − 0.8 V
Fully open3.2 − 4.9 V
NG Check for open and short in harness and
connector between ECM and throttle
position sensor (VTA line) (See page IN−28).
OK
Check and replace ECM (See page IN−28 ).
5 Check voltage between terminals VCC and E2 of ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals VCC and E2 of ECM con-
nector.
OK:
Voltage: 4.5 − 5.5 V
NG Check and replace ECM (See page IN−28 ).
OK
Check for open in harness and connector
between ECM and sensor (VCC line)
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI7130
Vehicle Speed50 − 65 km/h
(31 − 40 mph)
Idling
IG SW OFF 1 − 3 min.1 min. Time
(1)(2)(3) (4)
(5)
−
DIAGNOSTICS ENGINE
DI−43
1996 LAND CRUISER (RM451U)
DTC P0130 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40.
DTC No.DTC Detecting ConditionTrouble Area
P0130
Voltage output of heated oxygen sensor (bank 1 sensor 1)
remains at 0.4 V or more, or 0.55 V or less, during idling after
the engine is warmed up (2 trip detection logic)Heated oxygen sensor (bank 1 sensor 1)
 Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The heated oxygen sensor’s output voltage and the shortterm fuel trim value can be read using t\
he OBD
II scan tool or TOYOTA handheld tester.
WIRING DIAGRAM
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−35 for WIRING
DIAGRAM.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand−held tester to the DLC3.
(2) Switch the TOYOTA hand−held tester from normal mode to check mode (See page DI−3).
(3) Start the engine and warm it up withe all accessory switches OFF.
(4) Drive the vehicle at 50 − 65 km/h (31 − 40 mph) for 1 − 3 min. to warm up the heated oxygen sensor.
(5) Let the engine idle for 1 min.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the\
malfunction will not be possible.
If you do not have a TOYOTA hand −held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI5PA−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE6653
P24460A00950
ON
HT1HT2
(−) (+)
−
DIAGNOSTICS ENGINE
DI−47
1996 LAND CRUISER (RM451U)
DTC P0135 Heated Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 1)
DTC P0141 Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40.
DTC No.DTC Detecting ConditionTrouble Area
P0135
P0141
When the heater operates, heater current exceeds 2 A
(2 trip detection logic)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
Heater current of 0.25 A or less when the heater operates
(2 trip detection logic)
HINT:
Sensor 1 refers to the sensor closer to the engine body.
Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40 for WIRING
DIAGRAM.
INSPECTION PROCEDURE
1 Check voltage between terminals HT1, HT2 of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals HT1, HT2 of ECM connec-
tor and body ground.
HINT:
Connect terminal HT1 to bank 1 sensor 1.
Connect terminal HT2 to bank 1 sensor 2.
OK:
Voltage: 9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
DI5PC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−53
1996 LAND CRUISER (RM451U)
5 Check mass air flow meter and engine coolant temp. sensor
(See page SF−40 , SF−61 ).
NG Repair or replace.
OK
6 Check for spark and ignition (See page IG−1).
NG Repair or replace.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010