1996 TOYOTA LAND CRUISER ignition

DI−54
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0300 Random/Multiple Cylinder Misfire Detected
DTC P0301 Cylinder 1 Misfire Detected
DTC P0302 Cylinder 2 Misfire Detected
DTC P0303 Cylinder 3 Misfire Detected
DTC P0304 Cylinder 4 Misfire Detected
DTC P0305 Cylinder 5 Misfire Detected
DTC P0306 Cylinder 6 Misfire Detected
CIRCUIT DESCRIPTION
Misfire: The ECM uses the crankshaft position sensor and camshaft position senso\
r to monitor changes in
the crankshaft rotation for each cylinder.
The ECM counts the number of times the engine speed change rate indicates that misfire has occurred.
When the misfire rate equals or exceeds the count indicating that the engine condition has deteriorat\
ed, the
MIL lights up.
If the misfire rate is high enough and the driving conditions will cause catalyst overheating, the MIL blinks
when misfiring occurs.
DTC No.DTC Detecting ConditionTrouble Area
P0300Misfiring of random cylinders is detected during the any partic-
ular 200 or 1,000 revolutions Ignition system
 Injector
 Fuel line pressure
 EGR
 Compression pressure
 Valve clearance not to specification
 Valve timing
 Mass air flow meter
 Engine coolant temp. sensor
P0301
P0302
P0303
P0304
P0305
P0306For any particular 200 revolutions of the engine, misfiring is
detected which can cause catalyst overheating
(This causes MIL to blink)
For any particular 1,000 revolutions of the engine, misfiring is
detected which causes a deterioration in emission
(2 trip detection logic)
HINT:
When the 2 or more codes for a misfiring cylinder are recorded repeatedly bu\
t no random misfire code is
recorded, it indicates that the misfires were detected and recorded at d\
ifferent times.
DI5PF−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00164P03792
P22893
DI−56
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check spark plug and spark of misfiring cylinder.
PREPARATION:
(a) Remove No.2 and No.3 cylinder head cover.
(b) Disconnect the high −tension cord from spark plug.
(c) Remove spark plug.
CHECK:
(a) Check the carbon deposits on electrode.
(b) Check electrode gap.
OK:
(1) No large carbon deposit present.
Not wet with gasoline or oil.
(2) Electrode gap: 0.8 mm (0.031 in.).
PREPARATION:
(a) Install the spark plug to the high −tension cord.
(b) Ground the spark plug.
(c) Disconnect injector connector.
CHECK:
Check if spark occurs while engine is being cranked.
NOTICE:
To prevent excess fuel being injected from the injectors
during this test, don’t crank the engine for more than 5 − 10
seconds at a time.
OK:
Spark jumps across electrode gap.
NG Replace or check ignition system (See page IG−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00165
ON
#10 #20 #40 #50
#30 #60
BE6653
P24661
−
DIAGNOSTICS ENGINE
DI−57
1996 LAND CRUISER (RM451U)
2 Check voltage of ECM terminal for injector of failed cylinder.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between applicable terminal of ECM connec-
tor and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check injector of misfiring cylinder (See page SF−29).
NG Replace injector.
OK
Check for open and short in harness and con-
nector between injector and ECM (See page
IN−28 ).
4 Check fuel pressure (See page SF−6 ).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22425
Knock Sensor 1KNK2
Knock Sensor 2 KNK1
ECM
E1
E1
E5
E5
6
14
B
L−W
(On front side)
1
(On rear side) 1
−
DIAGNOSTICS ENGINE
DI−59
1996 LAND CRUISER (RM451U)
DTC P0325 Knock Sensor 1 Circuit Malfunction
DTC P0330 Knock Sensor 2 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensors are fitted one each to the front and rear of the left side of t\
he cylinder block to detect engine
knocking. This sensor contains a piezoelectric element which generates a voltage \
when it becomes de-
formed, which occurs when the cylinder block vibrates due to knocking. If engin\
e knocking occurs, ignition
timing is retarded to suppress it.
DTC No.DTC Detecting ConditionTrouble Area
P0325No knock sensor 1 signal to ECM with engine speed, between
1,800 rpm and 5.200 rpmOpen or short in knock sensor 1 circuit
 Knock sensor 1 (looseness)
 ECM
P0330No knock sensor 2 signal to ECM with engine speed, between
1,800 rpm and 5.200 rpmOpen or short in knock sensor 2 circuit
 Knock sensor 2 (looseness)
 ECM
If the ECM detects the above DTCs, it operates the fail safe function in w\
hich the corrective retard angle value
is set to the maximum value.
WIRING DIAGRAM
DI5PG−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P20769
(43 − 56 mph)
Vehicle Speed
70 − 90 km/h
Idling
IG SW OFF (1)(2) (3)
(4) (6)
(5)
Warm up 3 − 5 min. 2 min.
3 − 5 min.2 min.(7)
Time
DI−70
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
SYSTEM CHECK DRIVING PATTERN
(1) Connect the OBD II scan tool or TOYOTA hand −held tester to the DLC3.
(2) Start and warm up the engine with all accessories switched OFF.
(3) Run the vehicle at 70 − 90 km/h (43 − 56 mph) for 3 min. or more.
(4) Idle the engine for about 2 min.
(5) Stop at safe place and turn the ignition switch OFF.
(6) Start the engine and do steps (3) and (4) again.
(7) Check the ”READINESS TESTS” mode on the OBD II scan tool or\
TOYOTA hand−held tester.
If ”COMPL” is displayed and the MIL does not light up, the system \
is normal.
If ”INCMPL” is displayed and the MIL does not light up, run the ve\
hicle again and check it.
HINT:
”INCMPL” is displayed when either condition (a) or (b) exists.\
(a) The system check is incomplete.
(b) There is a malfunction in the system.
If there is a malfunction in the system, the MIL will light up after ste\
ps (2) to (6) above are done.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00168
ON
EGR Gas Temp.
Sensor ECM
19 9
1
2
BE6653
FI7055 THG
E2
E4
E5 5V
−
DIAGNOSTICS ENGINE
DI−71
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read value of EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 10° C (50°F) or more
HINT:
If there is and open circuit, the TOYOTA hand−held tester indicates 3.1 °C (37.6° F).
OK Go to step 4.
NG
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the EGR gas temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Confirm good connection at sensor. If OK, replace EGR gas temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00170
System : ON
System : OFF Air
GE
Air GE
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−73
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand −
held tester.
CHECK:
Check operation of VSV, when it is operated by the TOYOTA
hand −held tester.
OK:
EGR system is ON:
Air does not flow from pipe G to pipe E.
EGR system is OFF:
Air from pipe G is flowing out through pipe E.
OK Go to step 7.
NG
6 Check operation of the VSV for EGR (See page SF−60).
NG Replace VSV for EGR.
OK
Check for open in harness and connector be-
tween VSV and ECM (See page IN−28).
7 Check EGR vacuum modulator (See page EC−11 ).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−74
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
8 Check EGR valve (See page EC−11).
NG Repair or replace.
OK
9 Check value of EGR gas temp. sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester. (EGR system ON)
(e) Race the engine at 4,000 rpm for 3 mins.
CHECK:
Measure the EGR gas temp. while racing engine at 4,000 rpm.
OK:
EGR gas temp. after 3 mins.: 140° C (284°F) or more
NG Replace EGR gas temp. sensor.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010