Page 591 of 1399
Q04346
ATF Temperature SensorOIL
E5
R−W
BR−B
1 2
E2
E5 ECM
12 9 4 −
6 V
DI−154
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P0710 Transmission Fluid Temperature Sensor Cir-
cuit Malfunction (ATF Temperature Sensor)
CIRCUIT DESCRIPTION
The ATF temperature sensor converts fluid temperature into resistance value w\
hich is input into the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0710
Either (a) or (b) is detected for 0.5 sec. or more
(a) Temp. sensor resistance is less than 79 Ω
(b) After the engine has been operating for 15 min. or more, the resistance at the temp. sensor is more than 156 k ΩOpen or short in ATF temp. sensor circuit
ATF temp. sensor
ECM
WIRING DIAGRAM
DI5KK−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 593 of 1399
Q08221 Q08220D00081
(+) (−)
(+) (−)Air
DI−156
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P0750, P0755 Shift Solenoid A/B Malfunction (Shift Solenoid Valve No. 1/No. 2)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gea\
r position (1st, 2nd, 3rd or O/D
gear).
Then the ECM compares the actual gear with the shift schedule in the ECM mem\
ory to detect mechanical
trouble of the shift solenoid valves and valve body.
DTC No.DTC Detecting ConditionTrouble Area
P0750
P0755During normal driving, the gear required by the ECM does not
match the actual gear (2 trip detection logic)Shift solenoid valve No. 1/No. 2 is stuck open or closed
Valve body is blocked up or stuck
HINT:
Check the shift solenoid valve No. 1 when DTC P0750 is output and check shift\
solenoid valve No. 2 when
DTC P0755 is output.
INSPECTION PROCEDURE
1 Check shift solenoid valve No. 1 or No. 2 operation.
PREPARATION:
(a) Remove the oil pan.
(b) Remove the shift solenoid valve No. 1 or No. 2.
CHECK:
(a) Applying 490 kPa (5 kgf/cm2, 71 psi) of compressed air,
check that the shift solenoid valve does not leak air.
(b) When battery positive voltage is supplied to the shift sole-
noid valves, check they opens.
NG Replace shift solenoid valve No. 1 or No. 2.
OK
2 Check valve body (See page DI−147 ).
NG Repair or replace valve body.
OK
Repair transmission (See page AT −18).
DI5KM−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 597 of 1399
Q08224 Q08222D00083
DI−160
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check shift solenoid valve No. 1 or No. 2.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Disconnect the solenoid connector.
(d) Remove the shift solenoid valve No. 1 or No. 2.
CHECK:
(a) Measure the resistance between solenoid connector and
body ground.
(b) Connect positive lead to terminal of the solenoid con-
nector, negative lead to the solenoid body.
OK:
(a) Resistance: 11 − 15 Ω
(b) The shift solenoid valve No. 1 or No. 2 makes an
operating noise.
NG Replace shift solenoid valve No. 1 or No. 2.
OK
Repair or replace solenoid wire.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 602 of 1399
Q08224 Q08222D00083
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−165
1996 LAND CRUISER (RM451U)
3 Check shift solenoid valve SL.
PREPARATION:
(a) Jack−up the vehicle.
(b) Remove the oil pan.
(c) Disconnect the shift solenoid valve SL connector.
(d) Remove the shift solenoid valve SL.
CHECK:
(a) Measure the resistance between the shift solenoid valve
SL connector terminal and its body ground.
(b) Connect positive lead to terminal of the solenoid con-
nector, negative lead to the solenoid body.
OK:
(a) Resistance: 11 − 15 Ω
(b) Shift solenoid valve SL makes operation noise.
NG Replace shift solenoid valve SL.
OK
Check and replace or repair solenoid wire.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 603 of 1399
Q07352 AT5605D00084
Rotor
No. 2 Vehicle Speed Sensor Rotor
No. 2 Vehicle Speed Sensor
AT8761
5 V/div.
0 V
2 msec./div.
DI−166
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P1700 Speed Sensor No. 2 Circuit Malfunction
(No. 2 Vehicle Speed Sensor)
CIRCUIT DESCRIPTION
The No. 2 vehicle speed sensor detects the rotation speed of the transmissi\
on output shaft and sends sig-
nals to the ECM. The ECM determines the vehicle speed based on these signals\
.
An AC voltage is generated in the No. 2 vehicle speed sensor coil as the r\
otor mounted on the output shaft
rotates, and this voltage is sent to the ECM.
The gear shift point and lock −up timing are controlled by the ECM based on the signals from this vehic\
le
speed sensor and the throttle position sensor signal.
If the No. 2 vehicle speed sensor malfunctions, the ECM uses input signa\
ls from the No. 1 vehicle speed
sensor as a back −up signal.
DTC No.DTC Detecting ConditionTrouble Area
P1700
All conditions below are detected 500 times or more continu-
ously (2 trip detection logic)
(a) No signal from No. 2 vehicle speed sensor is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal is sent
(b) Vehicle speed: 9 km/h (5.6 mph) or more for as least 4 sec.
(c) Park/neutral position switch: OFF (Other than P or N posi-
tion)
(d) Transfer position: Other than N position
Open or short in No. 2 vehicle speed sensor circuit
No. 2 vehicle speed sensor
ECM
Reference:
Waveform between terminals SP2
+ and SP2− when the vehicle
speed is approx. 60 km/h (37 mph).
DI5KW−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 814 of 1399
−
ENGINE MECHANICAL CYLINDER HEAD
EM−29
1996 LAND CRUISER (RM451U)
16. DISCONNECT PS RESERVOIR TANK
Remove the 3 bolts and disconnect the reservoir tank.
17. DISCONNECT RADIATOR INLET HOSE
18. DISCONNECT NO. 3 WATER BYPASS HOSE
19. REMOVE GENERATOR (See page CH−8 )
20. REMOVE THROTTLE BODY (See page SF−45)
21. REMOVE OIL DIPSTICKS AND GUIDES FOR ENGINE AND TRANSMISSION
(a) Remove the 2 mounting bolts.
(b) Pull out the dipstick together with dipstick guide.
(c) Remove the O−ring from the dipstick guide.
22. REMOVE INTAKE MANIFOLD STAY
Remove the 2 bolts and intake manifold stay.
23. DISCONNECT FUEL INLET HOSE
Remove the union bolt and 2 gaskets, and disconnect the fuel
inlet hose from the fuel filter.
24. DISCONNECT ENGINE WIRE
(a) Disconnect the connectors. (1) Disconnect the ECT sender gauge connector.
(2) Disconnect the ECT cut switch connector.
(3) Disconnect the ECT sensor connector.
(4) Disconnect the knock sensor connector.
(5) Disconnect the crankshaft position sensor connec-tor.
(6) Remove the bolt and disconnect the engine wire from the cylinder block.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 815 of 1399
EM−30
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(b) Disconnect the connectors.
(1) Disconnect the knock sensor connector.
(2) Disconnect the oil level sensor connector.
(3) Disconnect the 2 connectors from the transmission.
(4) Disconnect the starter connector.
(c) Disconnect the 2 heated oxygen sensor connectors.
(d) Disconnect the PNP switch connector.
(e) Remove the 2 bolts and disconnect the engine wire from the intake manifold and cylinder block.
(f) Disconnect the PCV hose from the PCV valve.
(g) Remove the bolt holding the engine wire to the intake manifold.
(h) Disconnect the connectors. (1) Disconnect the connector for the emission controlvalve set assembly.
(2) Disconnect the 3 injector connectors.
(i) Disconnect the engine wire clamp.
(j) Disconnect the engine wire clamp.
(k) Disconnect the connectors.
(1) Disconnect the 3 injector connectors.
(2) Disconnect the EGR gas temp. sensor connector.
(l) Disconnect the clamp of the No. 6 injector wire from the bracket.
(m) Disconnect the engine wire from the cylinder head and in-
take manifold.
25. DISCONNECT NO. 2 WATER BYPASS PIPE
Remove the 3 bolts, and disconnect the bypass pipe from the
cylinder head.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 847 of 1399
EM−62
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(h) Connect the engine wire to the intake manifold and cylin-
der block with the 2 bolts.
(i) Connect the PNP switch connector.
(j) Connect the 2 heated oxygen sensor connectors.
(k) Connect the connectors.
(1) Connect the Knock sensor connector.
(2) Connect the oil level sensor connector.
(3) Connect the 2 connectors to tthe ransmission.
(4) Connect the starter connector.
(l) Connect the engine wire to the cylinder block with the bolt.
(m) Connect the connectors.
(1) Connect the ECT sender gauge connector.
(2) Connect the ECT cut switch connector.
(3) Connect the ECT sensor connector.
(4) Connect the knock sensor connector.
(5) Connect the crankshaft position sensor connector.
19. CONNECT FUEL INLET HOSE
Connect the fuel inlet hose to the fuel filter with 2 new gaskets
and the union bolt. Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
20. INSTALL INTAKE MANIFOLD STAY
Install the intake manifold stay with the 2 bolts. Torque: 36 N·m (360 kgf·cm, 26 ft·lbf)
21. INSTALL OIL DIPSTICKS AND GUIDES FOR ENGINE AND TRANSMISSION
(a) Install a new O−ring to the dipstick guide.
(b) Apply a light coat of engine oil on the O −ring.
(c) Push in the dipstick guide into the guide hole of the oil pan.
(d) Install the dipstick guide with the 2 bolts. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
22. INSTALL THROTTLE BODY (See page SF−48)
23. INSTALL GENERATOR AND DRIVE BELTS (See page CH−19 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
