1996 TOYOTA LAND CRUISER Air flow sensor

DI5KH−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−147
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but\
the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and\
proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle repair Matrix Chart
Chapter 3: Off−Vehicle repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given i\
n Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to cont\
inue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any\
of the other circuits, then check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion6. On−vehicle repair matrix chart
7. Off −vehicle repair matrix chart−
−
Vehicle does not move in a particular position or positions1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No up− shift (1st → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up −shift (2nd → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up− shift (3rd → O/D)
1. O/D main switck& O/D OFF indicator light circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Throttle position sensor circuit
6. Park/neutral position switch circuit
7. O/D cancel signal circuit
8. Engine coolant temp. sensor circuit
9. On−vehicle repair matrix chart
10.Off −vehicle repair matrix chart
11. ECMDI−174
DI−157 DI−87
DI−166 DI−35
DI−169
DI−172 DI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

D00076
Line
PressureDrain
Q08219
Q08226
D00087
(+)
(−)
(+)(−)
Air
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−161
1996 LAND CRUISER (RM451U)
DTC P0770 Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)
SYSTEM DESCRIPTION
The ECM uses the signals from the throttle position sensor, air −
flow meter and crankshaft position sensor to monitor the en-
gagement condition of the lock −up clutch.
Then the ECM compares the engagement condition of the
lock−up clutch with the lock −up schedule in the ECM memory
to detect mechanical trouble of the shift solenoid valve SL,
valve body and torque converter clutch.
DTC No.DTC Detecting ConditionTrouble Area
P0770
Lock− up does not occur when driving in the lock− up range
(normal driving at 80 km/h [50 mph] ), or lock− up remains ON
in the lock− up OFF range (2 trip detection logic)Shift solenoid valve SL is stuck open or closed
 Valve body blocked up or stuck
 Lock− up clutch
INSPECTION PROCEDURE
1 Check shift solenoid valve SL operation.
PREPARATION:
Remove the shift solenoid valve SL from the valve body.
CHECK:
(a) Applying 490 kPa (5 kgf/cm2, 71 psi) of compressed air,
check that the solenoid valve opens.
(b) When battery voltage is supplied to the shift solenoid
valve, check it does not leak air.
NG Replace shift solenoid valve SL.
OK
DI5KQ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z05490
Secondary LockPrimary Lock Lock Lock
Primary Lock Incomplate
(Secondary Lock Prevended) Primary Lock Complate
(Secondary Lock Permitted
Twin−Lock Complated
Z14034
Fig.1
Fig.2 Power Source
SafingSensor Squibs
Airbag
Sensor
RS−6
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
1996 LAND CRUISER (RM451U)
(4) Connector Twin −Lock Mechanism
With this mechanism connectors (male and female
connectors) are locked by 2 locking devices to in-
crease connection reliability. If the primary lock is in-
complete, ribs interfere and prevent the secondary
lock.
(b) When the vehicle is involved in a frontal collision in the hatched area (Fig. 1) and the shock is larger than the pre-
determined level, the SRS is activated automatically. A
safing sensor is designed to go on at a smaller decelera-
tion rate than the airbag sensor. As illustrated in Fig. 2,
ignition is caused when current flows to the squib, which
happens when a safing sensor and the airbag sensor go
on simultaneously.When a deceleration force acts on the
sensors, two squibs in the driver airbag and front passen-
ger airbag ignite and generate gas. The gas discharging
into the driver airbag and front passenger airbag rapidly
increases the pressure inside the bags, breaking open
the steering wheel pad and instrument panel door.
Bag inflation then ends, and the bags deflate as the gas
is discharged through discharge holes at the bag’s rear or
side.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010