1996 TOYOTA LAND CRUISER Ect

BE−54
−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
8. INSPECT DOOR UNLOCK DETECTION SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFF (Door Lock set to
LOCK)−No continuity
ON (Door Lock set toUNLOCK)1 − 3Continuity
If continuity is not as specified, replace the door lock assembly.
9. INSPECT POWER MAIN RELAY CONTINUITY (See
page BE−46 )
10. INSPECT DOOR LOCK CONTROL RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
2 − GroundDriver’s door courtesy switch position OFF (Door
closed)No continuity
2 − GroundDriver’s door courtesy switch position ON (Door
opened)Continuity
5 − GroundPassenger’s door lock switch position OFF (Door
locked)No continuity
5 − GroundPassenger’s door lock switch position ON (Door
unlocked)Continuity
6 − GroundDriver’s door lock switch position OFF (Door
locked)No continuity
6 − GroundDriver’s door lock switch position ON (Door
unlocked)Continuity
7 − GroundKey unlock warning switch position OFF (Ignition
Key Removed)No continuity
7 − GroundKey unlock warning switch position ON (Ignition
Key Set)Continuity
9 − GroundDriver’s door key lock and unlock switch position
OFF or LOCK (Door key free of turned to lock)No continuity
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
BE−55
1996 LAND CRUISER (RM451U)9 −
Ground
Driver’s door key lock and unlock switch position
UNLOCK (Door key turned to unlock)Continuity
10 − GroundDoor lock manual switch position OFF or
UNLOCKNo continuity
10 − GroundDoor lock manual switch position LOCKContinuity
11 − Ground
Door lock manual switch and passenger’s door
key lock and unlock switch position OFF or
UNLOCK
No continuity
11 − GroundDoor lock manual switch and passenger’s door
key lock and unlock switch position UNLOCKContinuity
12 − Ground
Driver’s and passenger’s door key lock and
unlock switch position OFF or UNLOCK (Door
key free or turned to unlock)
No continuity
12 − GroundDriver’s or passenger’s door key lock and unlock
switch position LOCK (Door key turned to lock)Continuity
14 − GroundPassenger’s door courtesy switch position OFF
(Door closed)No continuity
14 − GroundPassenger’s door courtesy switch position ON
(Door opened)Continuity
16 − GroundConstantContinuity
1 − GroundIgnition switch position LOCK or ACCNo voltage
1 − GroundIgnition switch position ONBattery positive voltage
8 − GroundConstantBattery positive voltage
If circuit is as specified, inspect the door lock signal.
If the circuit is not as specified, inspect the circuits connected
to other parts.
11. INSPECT DOOR LOCK SIGNAL
HINT:
When the relay circuit is as specified, inspect the door lock sig-
nal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 3 and the negative ( −) lead to terminal 4.
(c) Set the door lock manual switch to UNLOCK, and check
that the voltage rises from 0 V to battery positive voltage
for approximately 0.2 seconds.
(d) Reverse the polarity of the voltmeter leads.
(e) Set the door lock manual switch to LOCK, and check that the voltage rises from 0 V to battery positive voltage for
approximately 0.2 seconds.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−56
−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
12. NSPECT KEY−OFF POWER WINDOW SIGNAL
HINT:
When the relay circuit is as specified, inspect the key −off power
window signal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 15 and the negative ( −) lead to terminal 16.
(c) Close the door with ignition switch truned to LOCK or ACC, check that the meter needle indicates battery posi-
tive voltage.
(d) Open the door, check that the meter needle indicates 0 V.
(e) Turn the ignition switch ON, check that the meter needle
indicate battery positive voltage again.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MK−01
−
BODY ELECTRICAL SLIDING ROOF SYSTEM
BE−57
1195
Author: Date:
1996 LAND CRUISER (RM451U)
SLIDING ROOF SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1ML−01
BE−58
−
BODY ELECTRICAL SLIDING ROOF SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SLIDING ROOF SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
SLIDE OPEN3 − 4Continuity
SLIDE OFF−No continuity
SLIDE CLOSE4 − 6Continuity
TILT DOWN2 − 4Continuity
TILT OFF−No continuity
TILT UP5 − 4Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SLIDING ROOF LIMIT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
No.1 limit switch OFF
(SW pin released)−No continuity
No.1 limit switch ON(SW pin pushed in)1 − 5Continuity
No.2 limit switch OFF
(SW pin released)−No continuity
No.2 limit switch ON(SW pin pushed in)4 − 5Continuity
If continuity is not as specified, replace the switch.
3. INSPECT SLIDING ROOF MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 3, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns to clockwise.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL SLIDING ROOF SYSTEM
BE−59
1996 LAND CRUISER (RM451U)
4. INSPECT SLIDING ROOF MOT OR CIRCUIT BREAKER
OPERATION
(a) With the sliding roof in the fully opened position, hold the
sliding roof switch in ”OPEN” position and check that
there is a circuit breaker operation noise within 4 to 40 se-
conds.
(b) With the sliding roof in fully opened position, hold the slid-
ing roof switch in ”CLOSE” position and check that the
sliding roof begins to close within 60 seconds.
If operation is not as specified, replace the motor.
5. INSPECT SLIDING ROOF MOTOR WIRE CIRCUIT
(a) Check that there is continuity between terminals A2 and B2.
(b) Check that there is continuity between terminals A3 and B3.
(c) Check that there is continuity between terminals A6 and B1.
If continuity is not as specified, replace the switch.
6. INSPECT SLIDING ROOF CONTROL RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundSliding roof control switch position (SLIDE) OFF
or CLOSENo continuity
1 − GroundSliding roof control switch position (SLIDE)
OPENContinuity
2 − GroundSliding roof control switch position (SLIDE) OFF
or OPENNo continuity
2 − GroundSliding roof control switch position (SLIDE)
CLOSEContinuity
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−60
−
BODY ELECTRICAL SLIDING ROOF SYSTEM
1996 LAND CRUISER (RM451U) 3 −
Ground
Sliding roof control switch position (TILT) OFF or
DOWNNo continuity
3 − GroundSliding roof control switch position (TILT) UPContinuity
4 − GroundConstantNo continuity
4 − 5Constant*1Continuity
5 − GroundConstantNo continuity
7 − GroundSliding roof control switch position (TILT) OFF or
UPNo continuity
7 − GroundSliding roof control switch position (TILT) DOWNContinuity
8 − GroundNo.1 limit switch position OFF (Sliding roof tilted
up or open approx. 200 mm (7.87 in.))No continuity
8 − GroundNo.1 limit switch position ON (Except for
conditions mentioned above)Continuity
9 − GroundNo.2 limit switch position OFF (Sliding roof
closed)No continuity
9 − GroundNo.2 limit switch position ON (Sliding roof open)Continuity
11 − GroundConstantContinuity
6 − GroundIgnition switch position LOCK or ACC*2No voltage
6 − GroundIgnition switch position ONBattery positive voltage
12 − GroundConstantBattery positive voltage
*1: There is resistance because this circuit is include motor.
*
2: Exceptions: During 60 second period after ignition switch
ON → OFF (ACC) or until driver or passenger door is opened
after ignition switch ON → OFF (ACC).
If circuit is as specified, replace the relay.
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
7. INSPECT POWER MAIN RELAY CONTINUITY (See page BE−46 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MO−01
−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
BE−61
1199
Author: Date:
1996 LAND CRUISER (RM451U)
POWER SEAT CONTROL SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010