1996 TOYOTA LAND CRUISER oil level

−
BRAKE FRONT BRAKE PAD
BR−23
1996 LAND CRUISER (RM451U)
HINT:
Apply disc brake grease to both sides of the inner anti −squeal
shims (See page BR−21 ).
(d) Install the 2 pads.
HINT:
Apply disc brake grease to the caliper indicated by the arrows
(See page BR−33 ).
NOTICE:
Do not allow oil or grease to get on the rubbing face.
6. INSTALL ANTI −RATTLE SPRING AND 2 PINS
7. INSTALL CLIP
8. INSTALL FRONT WHEEL
9. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR−32
−
BRAKE REAR BRAKE PAD
1996 LAND CRUISER (RM451U)
(a) Install pad wear indicator plate to each pads.
(b) Install the anti−squeal shim to the outer pad.
(c) Install the 2 pads so the wear indicator plate is facing up-
ward.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
8. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in piston with a hammer handle or an equivalent.
HINT:
Always change the pads on one wheel at a time as there is a
possibility of the opposite piston flying out.
(c) Install the caliper carefully so the boot is not wedged.
(d) Install and torque the sliding main pin and sub pin. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
9. INSTALL REAR WHEEL
10. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IO−04
−
COOLING COOLANT
CO−1
696
Author: Date:
1996 LAND CRUISER (RM451U)
COOLANT
INSPECTION
HINT:
Check the coolant level when the engine is cold.
1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
The engine coolant level should be between the ”LOW” and ”FULL”\
lines.
If low, check for leaks and add engine coolant up to the ”FULL” line.
2. CHECK ENGINE COOLANT QUALITY
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator
are still hot, as fluid and steam can be blown out under pressure.
(b) There should not be any excessive deposits of rust or scale around the r\
adiator cap or radiator filler
hole, and the coolant should be free from oil.
If excessively dirty, replace the coolant.
(c) Reinstall the radiator cap.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22480
BatteryStarter
FL MAIN
FL AM2EFI
EFI Main Relay
IG Switch IG
ST
Park/Neutral
Position SwitchCircuit Opening
Relay
Fuel Pump Relay
Fuel Pump
From Crankshaft Position
Sensor Fuel Pump
Resistor
(STA Signal)
(NE Signal) MRLY
FC
STA
NE
Tr1
Tr2
ECM
IGN FPR
−
DIAGNOSTICS ENGINE
DI−11 5
1996 LAND CRUISER (RM451U)
Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows form terminal ST of the igni\
tion switch to
terminal STA of ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr1 is turned ON, current flows to coil of the circuit
opening relay, the relay switches on, power is supplied to the fuel pump and the fuel\
pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr1 ON (circuit opening relay ON) and
the fuel pump also keeps operating.
The fuel pump speed is controlled at 2 levels (high speed or low speed) b\
y the condition of the engine (start-
ing, light load, heavy load). When the engine starts (STA ON), Tr2 in the ECM is OFF, so battery voltage is
applied directry to the fuel pump. Fuel pump operates at high speed.
After the engine starts, during idling or light loads, since Tr2 goes ON, power is supplied to the fuel pump
via the fuel pump resistor.
Fuel pump operates at low speed.
DI5PY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−14
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
9. DISCONNECT OIL COOLER PIPE BRACKET FROM
NO. 1 OIL PAN
10. REMOVE OIL LEVEL SENSOR
(a) Remove the 4 bolts and level sensor.
(b) Remove the gasket from the level sensor.
11. REMOVE BOLTS HOLDING NO.1 OIL PAN TO TRANS-
MISSION HOUSING
Remove the 6 bolts.
12. REMOVE NO. 2 OIL PAN (See page LU−5)
13. REMOVE NO. 1 OIL PAN (See page LU−5)
14. REMOVE CRANKSHAFT PULLEY
(a) Using SST, remove the pulley bolt. SST 09213−58012, 09330 −00021
(b) Remove the crankshaft pulley.
HINT:
If necessary, remove the pulley with SST. SST 09950−50010 (09951 −05010, 09952−05010,
09953 −05010, 09953 −05020, 09954−05020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−23
1996 LAND CRUISER (RM451U)
15. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
16. CONNECT OIL COOLER PIPE BRACKET TO NO. 1 OIL
PA N
17. INSTALL CYLINDER HEAD (See page EM−54 )
NOTICE:
However, for the installation of the camshaft timing gear
and timing chain, follow the below procedure. Align the
blight link of the timing chain and camshaft timing gear
mark, and install them to the camshaft.
18. INSTALL WATER PUMP
Install a new gasket and water pump with the 4 bolts and 2 nuts.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
19. INSTALL RADIATOR PIPE
(a) Connect the No.2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No.1 oil
pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
20. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
21. INSTALL RADIATOR (See page CO−16 )
22. FILL ENGINE WITH OIL
23. INSTALL ENGINE UNDER COVER
24. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010