1996 TOYOTA LAND CRUISER oil level
[x] Cancel search: oil levelPage 815 of 1399
EM−30
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(b) Disconnect the connectors.
(1) Disconnect the knock sensor connector.
(2) Disconnect the oil level sensor connector.
(3) Disconnect the 2 connectors from the transmission.
(4) Disconnect the starter connector.
(c) Disconnect the 2 heated oxygen sensor connectors.
(d) Disconnect the PNP switch connector.
(e) Remove the 2 bolts and disconnect the engine wire from the intake manifold and cylinder block.
(f) Disconnect the PCV hose from the PCV valve.
(g) Remove the bolt holding the engine wire to the intake manifold.
(h) Disconnect the connectors. (1) Disconnect the connector for the emission controlvalve set assembly.
(2) Disconnect the 3 injector connectors.
(i) Disconnect the engine wire clamp.
(j) Disconnect the engine wire clamp.
(k) Disconnect the connectors.
(1) Disconnect the 3 injector connectors.
(2) Disconnect the EGR gas temp. sensor connector.
(l) Disconnect the clamp of the No. 6 injector wire from the bracket.
(m) Disconnect the engine wire from the cylinder head and in-
take manifold.
25. DISCONNECT NO. 2 WATER BYPASS PIPE
Remove the 3 bolts, and disconnect the bypass pipe from the
cylinder head.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 847 of 1399
EM−62
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(h) Connect the engine wire to the intake manifold and cylin-
der block with the 2 bolts.
(i) Connect the PNP switch connector.
(j) Connect the 2 heated oxygen sensor connectors.
(k) Connect the connectors.
(1) Connect the Knock sensor connector.
(2) Connect the oil level sensor connector.
(3) Connect the 2 connectors to tthe ransmission.
(4) Connect the starter connector.
(l) Connect the engine wire to the cylinder block with the bolt.
(m) Connect the connectors.
(1) Connect the ECT sender gauge connector.
(2) Connect the ECT cut switch connector.
(3) Connect the ECT sensor connector.
(4) Connect the knock sensor connector.
(5) Connect the crankshaft position sensor connector.
19. CONNECT FUEL INLET HOSE
Connect the fuel inlet hose to the fuel filter with 2 new gaskets
and the union bolt. Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
20. INSTALL INTAKE MANIFOLD STAY
Install the intake manifold stay with the 2 bolts. Torque: 36 N·m (360 kgf·cm, 26 ft·lbf)
21. INSTALL OIL DIPSTICKS AND GUIDES FOR ENGINE AND TRANSMISSION
(a) Install a new O−ring to the dipstick guide.
(b) Apply a light coat of engine oil on the O −ring.
(c) Push in the dipstick guide into the guide hole of the oil pan.
(d) Install the dipstick guide with the 2 bolts. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
22. INSTALL THROTTLE BODY (See page SF−48)
23. INSTALL GENERATOR AND DRIVE BELTS (See page CH−19 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 862 of 1399
−
ENGINE MECHANICAL ENGINE UNIT
EM−77
1996 LAND CRUISER (RM451U)
9. INSTALL OIL DIPSTICK GUIDE FOR TRANSMISSION
(a) Install a new O−ring to the dipstick guide.
(b) Apply a light coat of ATF to the O −ring.
(c) Connect the dipstick guide end to the tube of the oil pan, and install the dipstick guide with the 2 bolts.
(d) Install the dipstick.
(e) Connect the 2 breather hoses.
10. INSTALL ENGINE AND TRANSMISSION ASSEMBLY IN VEHICLE
(a) Attach the engine hoist chain to the engine hangers.
(b) Lower the engine and transmission assembly into the en-
gine compartment.
(c) Insert the stud bolts of the front engine mounting insula- tors into the stud bolt holes of the frame.
(d) Temporarily install the 2 nuts holding the engine front mounting insulators to the frame crossmember.
(e) Keep the engine level with a jack.
(f) Remove the hoist chain.
11. INSTALL FRAME CROSSMEMBER
(a) Temporarily install the crossmember to the engine rear mounting insulator with the 2 nuts.
(b) Install the 8 bolts holding the crossmember to the frame. Torque: 61 N·m (620 kgf·cm, 45 ft·lbf)
(c) Tighten the 2 nuts holding the crossmember to the engine
rear mounting insulator.
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
12. TIGHTEN NUTS HOLDING ENGINE FRONT MOUNT- ING INSULATORS TO FRAME
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
13. CONNECT GROUND STRAP TO HEAT INSULATOR
14. INSTALL FRONT EXHAUST PIPE
(a) Install 2 new gaskets and the front exhaust pipe with the
4 nuts.
Torque: 63 N·m (630 kgf·cm, 46 ft·lbf)
(b) Install the No.1 support bracket with the 2 bolts.
Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(c) Connect the clamp and tighten the clamp bolt. Torque: 19.5 N·m (195 kgf·cm, 14 ft·lbf)
(d) Connect the front exhaust pipe to the rear TWC with a
new gasket, 2 bolts and 2 nuts.
Torque: 46 N·m (470 kgf·cm, 34 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 866 of 1399
−
ENGINE MECHANICAL ENGINE UNIT
EM−81
1996 LAND CRUISER (RM451U)
26. CONNECT EVAP HOSE
27. CONNECT BRAKE BOOSTER VACUUM HOSE
28. CONNECT HEATER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the engine wire and ground strap with the 2 bolts.
29. CONNECT HEATER HOSES
30. CONNECT ACCELERATOR CABLE TO THROTTLE BODY
31. CONNECT CRUISE CONTROL ACTUATOR CABLE TO
THROTTLE BODY
32. INSTALL AIR CLEANER CASE
33. INSTALL AIR CLEANER HOSE AND CAP
34. CONNECT OIL COOLER HOSE TO OIL COOLER PIPE
35. INSTALL RADIATOR (See page CO−16)
36. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
37. INSTALL BATTERY TRAY AND BATTERY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery and hold−down clamp with the nuts.
(d) Connect the battery cables.
38. FILL WITH ENGINE OIL
39. FILL RADIATOR WITH ENGINE COOLANT
40. START ENGINE AND CHECK FOR LEAKS
41. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
42. CHECK IGNITION TIMING (See page EM−10)
43. INSTALL HOOD
44. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
45. RECHECK ENGINE COOLANT AND ENGINE OIL LEV-
ELS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 910 of 1399
LU0817
LU08N−03
EM1759
P22601
Oil Pressure Gauge
P08343
Adhesive
−
LUBRICATION OIL AND FILTER
LU−1
712
Author: Date:
1996 LAND CRUISER (RM451U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SH Energy−Conserving II multigrade en-
gine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra-
tion, with SAE 5W −30 being the preferred engine oil.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the di\
p-
stick.
If low, check for leakage and add oil up to ”F” mark.
3. REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE
4. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
5. CHECK OIL PRESSURE Oil pressure:
At idle
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 490 kPa (2.5 − 5.0 kgf/cm
2, 36 − 71 psi)
6. REMOVE OIL PRESSURE GAUGE AND REINSTALL OIL PRESSURE SWITCH
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Reinstall the oil pressure switch.
7. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 911 of 1399
LU0KE−03
LU−2
−
LUBRICATION OIL AND FILTER
1996 LAND CRUISER (RM451U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dry-
ness, irritation and dermatitis. In addition, used engine oil
contains potentially harmful contaminants which may
cause skin cancer.Care should be taken, therefore, when
changing engine oil to minimize the frequency and length
of time your skin is exposed to used engine oil. Protective
clothing and gloves that cannot be penetrated by oil should
be worn. The skin should be thoroughly washed with soap
and water, or use water−less hand cleaner, to remove any
used engine oil. Do not used gasoline, thinners, or sol-
vents.In order to preserve the environment, used oil and
used oil filters must be disposed of only at designated dis-
posal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter. SST 09228−44011
(b) Check and clean the oil filter installation surface.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
(e) Using SST, tighten it an additional 3/4 turn. SST 09228−44011
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Fill with new engine oil. Oil grade:
See step 1 in oil pressure check
Capacity:
Drain and refill
w/ Oil filter change
7.2 liters (7.5 US qts, 6.3 lmp. qts)
w/o Oil filter change
6.9 liters (7.3 US qts, 6.1 lmp. qts)
Dry fill
8.0 liters (8.5 US qts, 7.0 lmp. qts)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE OIL LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 915 of 1399
LU−6
−
LUBRICATION OIL PUMP
1996 LAND CRUISER (RM451U)
10. REMOVE OIL LEVEL SENSOR
(a) Remove the 4 bolts and level sensor.
(b) Remove the gasket from the level sensor.
11. REMOVE BOLTS HOLDING NO.1 OIL PAN TO TRANS-
MISSION HOUSING
Remove the 6 bolts.
12. REMOVE NO.2 OIL PAN
(a) Remove the 17 mounting bolts and 2 nuts.
(b) Insert the blade of SST between the No.1 and No.2 oil pans, cut off applied sealer and remove the No.2 oil pan.
SST 09032−00100
NOTICE:
Be careful not to damage the No.2 oil pan contact surface
of the No.1 oil pan.Be careful not to damage the oil pan
flange.
13. REMOVE NO.1 OIL PAN
(a) Remove the 21 mounting bolts and 2 nuts.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 923 of 1399
LU−14
−
LUBRICATION OIL PUMP
1996 LAND CRUISER (RM451U)
Install the 6 bolts.
Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
11. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
12. CONNECT OIL COOLER PIPE BRACKET TO NO.1 OIL
PA N
13. INSTALL CYLINDER HEAD(See page EM−54)
14. INSTALL WATER PUMP
Install a new gasket and water pump with the 4 bolts and 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
15. INSTALL RADIATOR PIPE
(a) Connect the No.2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No.1 oil pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
16. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts. Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
17. INSTALL RADIATOR (See page CO−16 )
18. INSTALL ENGINE UNDER COVER
19. FILL WITH ENGINE OIL
20. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010