1996 TOYOTA LAND CRUISER AC pressure switch

AC2R7−04
AC0943
SST
AC0944
SST
AC0945
SST
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
AC−35
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. RUN ENGINE AT IDLE SPEED WITH A/C SWITCH ON
FOR 10 MINUTES
2. STOP ENGINE
3. DISCONNECT NEGATIVE ( −) TERMINAL CABLE
FROM BATTERY
4. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
5. DISCONNECT DISCHARGE AND SUCTION HOSES
Remove the 2 bolts and disconnect the both hoses.
NOTICE:
Cap the open fittings immediately to keep the moisture or
dirt out of the system.
6. REMOVE ENGINE UNDER COVER
7. REMOVE DRIVE BELT (See page AC−16)
8. REMOVE COMPRESSOR
(a) Disconnect the connector.
(b) Remove the 4 bolts and pull the compressor upward.
9. REMOVE COMPRESSOR (See page AC−35 )
10. REMOVE PRESSURE PLATE
(a) Using SST and a socket wrench, remove the shaft bolt. Torque: 13.2 N·m (135 kgf·cm, 9 ft·lbf)
SST 07112 −76060
(b) Install a SST on the pressure plate. SST 07112 −66040
(c) Using SST and a socket wrench, remove the pressure plate.
SST 07112 −76060
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N16452
AC2SB−01
Z13470
Low Pressure Side
ON (Continuity)
196 kpa
(2.0 kgf·cm
2, 28 psi)
OFF (No Continuity) High Pressure Side
3,140 kpa
(32.0 kgf·cm2, 455 psi)
OFF (No Continuity)
−
AIR CONDITIONING PRESSURE SWITCH
AC−61
1388
Author: Date:
1996 LAND CRUISER (RM451U)
PRESSURE SWITCH
ON−VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET
2. DISCONNECT CONNECTOR FROM PRESSURE
SWITCH
3. RUN ENGINE AT APPROX. 1,500 RPM
4. INSPECT PRESSURE SWITCH OPERATION
(a) Connect the positive (+) lead from the ohmmeter to termi-
nal 2 and the negative ( −) lead to terminal 1.
(b) Check continuity between terminals when refrigerant pressure is changed, as shown in the illustration.
If operation is not as specified, replace the pressure switch.
5. STOP ENGINE AND REMOVE MANIFOLD GAUGE
SET
6. CONNECT CONNECTOR TO PRESSURE SWITCH
~11L
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2SC−01
N14163
AC−62
−
AIR CONDITIONING PRESSURE SWITCH
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
HINT:
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of refrig-
erant.
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
2. REMOVE PRESSURE SWITCH
(a) Disconnect the connector.
(b) Remove the pressure switch from the liquid tube. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
HINT:
At the time of installation, lubricate a new O− ring with compres-
sor oil and install the switch.
HINT:
Lock the switch mount on the tube with an open end wrench,
being careful not to deform the tube, and remove the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2SD−01
−
AIR CONDITIONING PRESSURE SWITCH
AC−63
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page AC−62 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2SI−01
AC−74
−
AIR CONDITIONING AIR CONDITIONING AMPLIFIER
1401
Author: Date:
1996 LAND CRUISER (RM451U)
AIR CONDITIONING AMPLIFIER
ON−VEHICLE INSPECTION
INSPECT AMPLIFIER CIRCUIT
(a) Disconnect the amplifier and inspect the connector on the
wire harness side, as shown in the chart below.
Test conditions:
Ignition switch ON
A/C switch ON
Temperature control lever MAX COOL
Blower control switch HI
Tester connectionConditionSpecifeid condition
6 − GroundConstantContinuity
8 − 9ConstantContinuity
9 − 6ConstantApprox. 1.5 k Ω at 25 ° C (77 °F)
2 − GroundA/C switch ONBattery positive voltage
2 − GroundA/C switch OFFNo voltage
5 − GroundStart engineApprox. 10 to 14 v
5 − GroundStop engineNo voltage
If circuit is as specified, try replacing the amplifier with a new
one. If the circuit is not as specified, inspect the circuits con-
nected to other parts.
(b) Connect the connector to A/C amplifier and inspect wire
harness side connector from the back side, as shown in
the chart below.
Test conditions:
Ignition switch ON
A/C switch ON
Temperature control lever MAX COOL
Blower control switch HI
Tester connectionConditionSpecified Condition
3 − GroundRefrigeration pressure
2.0 − 32 kgf/cm3Battery positive voltage
3 − GroundRefrigeration pressure
less than 2.0 − 32 kgf/cm3 or moreNo voltage
If circuit is not as specified, replace the amplifier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−6
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Engine oil level warning light does not light up.
1. Bulb
2. Meter Circuit
3. Engine Oil Level Warning Switch
4. Wire Harness−
BE−32
BE−34 −
Low oil pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−32
BE−34 −
Fuel level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−34
BE−32 −
INDICATOR LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
High beam indicator light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness−
BE−19
BE−32 −
Shift indicator lights do not light up. (ALL)
1. Shift Position Indicator Wiring Circuit
2. Park/Neutral Position Switch
3. Wire Harness
4. Bulb−
BE−34 AT −6
−
Shift indicator lights do not light up. (L, 2, D)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Park/Neutral Position Switch
4. Light Control Rheostat
5. Wire Harness−
BE−34 AT −6
BE−34 −
Shift indicator lights do not light up. (PWR)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Pattern Select Switch
4. Wire Harness−
BE−34 AT −6
−
Shift indicator lights do not light up. (2nd START)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. ECM
4. Wire Harness−
AT −6
−
−
Only one shift indicator does not light up.1. Bulb
2. Shift Position Indicator Wiring Circuit−
BE−34
Indicator lights do not light up. (Except Turn, Hi −beam)1. GAUGE Fuse (I/P F/B)
2. Wire Harness−
−
O/D OFF indicator light does not light up.
1. Bulb
2. O/D Main Switch
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Wire Harness−
−
−
Cruise control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Engine Coolant
Temperature
Gauge
Ignition Switch
Battery Sender
Gauge
Z06815
Engine
Coolant T emperature Gauge
Ignition
Switch Tester Bulb
(3.4 W)
Battery
BE1222
Oil Pressure Gauge
Ignition
Switch Sender
Gauge
Battery
−
BODY ELECTRICAL COMBINATION METER
BE−37
1996 LAND CRUISER (RM451U)
11. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge. Then re-
check the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
12. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (Ω )
A − B71 − 79
A − C117 − 141
B − C185 − 215
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the above order. This circuit include the
diode.
If resistance value is not as specified, replace the receiver
gauge.
13. INSPECT OIL PRESSURE RECEIVER GAUGE OP-
ERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates LOW.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010