1996 TOYOTA LAND CRUISER Ect

TR0BA−01
TF0893
SST
Q00538
TF0896
SST
−
TRANSFER IDLER GEAR
TR−17
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL FRONT TAPER ROLLER BEARING
Using SST and a press, install the front taper roller bearing.
SST 09316−60011 (09316 −00011, 09316−00031)
2. INSTALL HIGH AND LOW CLUTCH SLEEVE
HINT:
Make sure to install the high and low clutch sleeve in the correct
direction.
3. INSTALL NEEDLE ROLLER BEARING AND IDLER LOW GEAR TO IDLER GEAR
(a) Apply gear oil to the needle roller bearing.
(b) Install the needle roller bearing and idler low gear.
4. INSTALL REAR TAPER ROLLER BEARING
Using SST and a press, install the rear taper roller bearing. SST 09316−60011 (09316 −00011, 09316−00071)
5. INSPECT IDLER LOW GEAR RADIAL AND THRUST CLEARANCE
(See page TR−16 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BC−01
TF0900
TF0944
Q07101
SST
Q07102
SST
Q07103
SST
−
TRANSFER CENTER DIFFERENTIAL
TR−19
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND
THRUST CLEARANCE
(a) Using a feeler gauge, measure the high speed output gear thrust clearance.
Standard clearance:
0.10−0.25 mm (0.0039 −0.0098 in.)
Maximum clearance:
0.25 mm (0.0098 in.)
(b) Using a dial indicator, measure the high speed output gear radial clearance.
Standard clearance:
0.035−0.091 mm (0.0014 −0.0036 in.)
Maximum clearance:
0.091 mm (0.0036 in.)
2. REMOVE FRONT DRIVE GEAR PIECE
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST and a press, remove the front drive gear piece.
SST 09950−00020, 09950 −60010 (09951−00320)
NOTICE:
Be careful not to drop the center differential assembly.
3. REMOVE FRONT TAPER ROLLER BEARING
Using SST and a press, remove the front taper roller bearing.
SST 09950−00020
4. REMOVE HIGH SPEED OUTPUT GEAR
5. REMOVE NEEDLE ROLLER BEARING
6. REMOVE HIGH AND LOW CLUTCH SLEEVE AS-
SEMBLY
7. REMOVE HIGH SPEED OUTPUT GEAR BUSHING AND CLUTCH HUB
(a) Using SST and a press, remove the high speed output
gear bushing and clutch hub.
SST 09550−00020, 09950 −00030, 09950−60010
(09951 −00320)
(b) Using a magnetic finger, remove the straight pin from the
differential front case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BD−01
Q07115
SSTStamp
TF1012
TF0913
TF0917
−
TRANSFER CENTER DIFFERENTIAL
TR−21
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the differential rear case.
SST 09612−24014 (09612 −10050)
HINT:
Install the bearing to the differential rear case, taking care that
its stamped side comes in contact with SST.
(b) Install the snap ring.
2. INSTALL LOW GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the low gear in boiling water.
(c) Carefully remove the low gear from the water.
(d) After the moisture on the low gear has completely evapo- rated, quickly install the low gear to the differential case.
3. INSTALL PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Install the front side gear and thrust washer to the differ- ential front case.
(b) Install the pinion shaft, 2 pinion gears and thrust washers
to the differential front case.
(c) Using a dial indicator, measure the front case backlash.
HINT:
Push the pinion shaft. Minimum backlash: 0.05 mm (0.0020 in.)
If the backlash is not within the specification, replace the thrust
washer with one of the correct size and reinstall the thrust wash-
er.
Thickness mm (in.)Thickness mm (in.)
1.70 (0.0669)2.45 (0.0965)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q00546
SST
Q00555
Q00539
SSTSST
Q00540
SST
SST
TF0931
−
TRANSFER CENTER DIFFERENTIAL
TR−23
1996 LAND CRUISER (RM451U)
(c) Using SST and a press, install the high speed output gear
bushing.
SST 09316−12010, 09316 −60011 (09316−00011)
NOTICE:
Before pressing, align the holes on the bushing and shaft
so that the pin on the shaft aligned with the cutting portion
of the bushing.
11. INSTALL HIGH AND LOW CLUTCH SLEEVE
HINT:
Make sure to install the high and low clutch sleeve in the correct
direction.
12. INSTALL HIGH SPEED OUTPUT GEAR AND NEEDLE ROLLER BEARING
(a) Apply gear oil to the needle roller bearing.
(b) Install the high speed output gear and needle roller bear-
ing.
13. INSTALL FRONT TAPER ROLLER BEARING
Using SST and a press, install the front taper roller bearing. SST 09316−12010, 09316 −60011 (09316−00011)
14. INSTALL FRONT DRIVE GEAR PIECE
Using SST and a press, install the front drive gear piece. SST 09316−12010, 09316 −60011 (09316−00011)
15. INSTALL SNAP RING
(a) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)MarkThickness mm (in.)
A2.00 (0.0787)G2.60 (0.1024)
B2.10 (0.0827)H2.70 (0.1063)
C2.20 (0.0866)J2.80 (0.1 102)
D2.30 (0.0906)K1.80 (0.0709)
E2.40 (0.0945)L1.90 (0.0748)
F2.50 (0.0984)−−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR−24
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U)
(b) Using a snap ring expander, install a new snap ring.
16. INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND THRUST CLEARANCE (See page TR−19 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BE−01
Z18836
Front Output Shaft
Dust Deflector
 Oil Seal Housing Ball Bearing

Snap Ring Drive Clutch Hub

Snap Ring
 Snap Ring
−
TRANSFER FRONT EXTENSION HOUSING
TR−25
835
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BF−01
Q07133
SST
TF0938
TF0940
SST
TR−26
−
TRANSFER FRONT EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE DRIVE CLUTCH HUB
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST, remove the drive clutch hub. SST 09950−40010
2. REMOVE FRONT OUTPUT SHAFT
Using a plastic hammer, drive out the front output shaft.
3. REMOVE DUST DEFLECTOR
(a) Using SST and a press, remove the dust deflector. SST 09950−00020
(b) Using a screwdriver and hammer, tap the dust deflector
and remove it from the extension housing.
4. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal from the front extension
housing.
5. REMOVE BALL BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a press, remove the ball bearing. SST 09316−60011 (09316 −00011, 09316−00071)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BG−01
TF0967
SST
TF0943
SST
TF0939
TF0945
SST
−
TRANSFER FRONT EXTENSION HOUSING
TR−27
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL DUST DEFLECTOR
(a) Using SST and a press, install a new dust deflector to the
front extension housing.
SST 09223−15020, 09950 −70010 (09951−07150)
(b) Using SST and a press, install a new dust deflector to the
front output shaft.
SST 09316−20011, 09316 −60011 (09316−00011)
2. INSTALL BALL BEARING
(a) Using SST and a press, install the ball bearing to the front
extension housing.
SST 09316−60011 (09316 −00011, 09316−00031)
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
A1.7 (0.0669)
B1.8 (0.0709)
(c) Using a screwdriver, install a new snap ring.
3. INSTALL OIL SEAL
Using SST and a hammer, drive in a new oil seal to the front ex-
tension housing.
SST 09316−60011 (09316 −00011, 09316−00061)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010