1996 TOYOTA LAND CRUISER Rear bearing

Q07113
SST
Q07114
SST
SST
Bearing
TR−20
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U)
8. REMOVE REAR TAPER ROLLER BEARING
Using SST and a press, remove the rear taper roller bearing.
SST 09950−00020, 09950 −60010 (09951−00320)
9. REMOVE DIFFERENTIAL REAR CASE
Remove the 12 bolts and differential rear case.
10. REMOVE REAR SIDE GEAR AND THRUST WASHER
11. REMOVE PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Remove the straight pin from the pinion shaft.
(b) Remove the pinion shaft, 2 pinion gears and thrust wash-
ers.
(c) Remove the front side gear and thrust washer.
12. REMOVE LOW GEAR
Using a plastic hammer, tap and remove the low gear.
NOTICE:
Be careful not to damage the low gear.
13. REMOVE NEEDLE ROLLER BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a hammer, remove the needle roller bear-
ing from the differential rear case.
SST 09223 −00010, 09950 −60010 (09951 −00400),
09950 −70010 (09951 −07150)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BD−01
Q07115
SSTStamp
TF1012
TF0913
TF0917
−
TRANSFER CENTER DIFFERENTIAL
TR−21
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the differential rear case.
SST 09612−24014 (09612 −10050)
HINT:
Install the bearing to the differential rear case, taking care that
its stamped side comes in contact with SST.
(b) Install the snap ring.
2. INSTALL LOW GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the low gear in boiling water.
(c) Carefully remove the low gear from the water.
(d) After the moisture on the low gear has completely evapo- rated, quickly install the low gear to the differential case.
3. INSTALL PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Install the front side gear and thrust washer to the differ- ential front case.
(b) Install the pinion shaft, 2 pinion gears and thrust washers
to the differential front case.
(c) Using a dial indicator, measure the front case backlash.
HINT:
Push the pinion shaft. Minimum backlash: 0.05 mm (0.0020 in.)
If the backlash is not within the specification, replace the thrust
washer with one of the correct size and reinstall the thrust wash-
er.
Thickness mm (in.)Thickness mm (in.)
1.70 (0.0669)2.45 (0.0965)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0920
Q00534
SST
Q00547
SST
Q00549
TR−22
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U) 1.85 (0.0728)
2.60 (0.1024)
2.00 (0.0787)2.75 (0.1083)
2.15 (0.0846)2.90 (0.1
142)
2.30 (0.0906)3.05 (0.1201)
(d) In the same way, measure the rear case backlash.
4. INSTALL STRAIGHT PIN TO PINION SHAFT
5. INSTALL REAR SIDE GEAR AND THRUST WASHER
6. INSTALL DIFFERENTIAL REAR CASE
Install the differential rear case and 12 set bolts.
7. TORQUE REAR CASE SET BOLT
(a) Torque the rear case 12 set bolts.
Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
(b) Turn the pinion gear.
(c) Loosen the rear case 12 set bolts.
(d) Torque the rear case 12 set bolts. Torque: 98 N·m (1,000 kgf·cm, 72 ft·lbf)
8. INSTALL REAR TAPER ROLLER BEARING
Using SST and a press, install the rear taper roller bearing. SST 09316−12010
9. INSTALL CLUTCH HUB
Using SST and a press, install the clutch hub. SST 09316−12010, 09316 −60011 (09316−00011)
10. INSTALL HIGH SPEED OUTPUT GEAR BUSHING
(a) Apply MP grease to the straight pin.
(b) Install the straight pin, as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BH−01
Q08383
Center Differential Control
Couping Assembly
Snap ring Vehicle Speed sensor
Drive Gear Ball Bearing
 Snap Ring
Snap Ring
Oil Pump Plate
Drive Rotor
Oil Pump Cover
Rear Extension housing
Oil Pump Drive Shaft Ball
Spring 
Screw Plug
Valve Seat

Dust Deflector
 Oil Seal Seal Ring
Rear Output Shaft
 Non− reusable Part
 Precoated part Separator
Driven Rotor
−
TRANSFER REAR EXTENSION HOUSING
TR−29
839
Author: Date:
1996 LAND CRUISER (RM451U)
REAR EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0959
SST
Q08385
Q08481
SST
−
TRANSFER REAR EXTENSION HOUSING
TR−31
1996 LAND CRUISER (RM451U)
9. REMOVE REAR OUTPUT SHAFT
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST and a hammer, remove the rear output shaft.
SST 09325−12010
(c) Remove the 2 seal rings from the rear output shaft.
10. REMOVE DUST DEFLECTOR
(a) Using a screwdriver and hammer, remove the rear exten-
sion housing dust deflector.
(b) Using a screwdriver and hammer, remove the rear output
shaft dust deflector.
11. REMOVE OIL SEAL
Using a screwdriver, pry out the oil seal from the rear extension
housing.
12. REMOVE BALL BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a press, remove the ball bearing to the rear extension housing.
SST 09316−60011 (09316 −00011, 09316−00021)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0CO−01
TF0964
SST
TF0962
Q08482
SST
TF0967
SST
Q08482
SST
−
TRANSFER REAR EXTENSION HOUSING
TR−33
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL BALL BEARING
(a) Using SST and a press, install the ball bearing.
SST 09316−60011 (09316 −00011, 09316−00031)
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
A1.7 (0.0669)
B1.8 (0.0709)
(c) Using a screwdriver, install a new snap ring.
2. INSTALL DUST DEFLECTOR
(a) Using SST and a hammer, install a new rear extension housing dust deflector.
SST 09316−60011 (09316 −00011, 09316−00041)
(b) Using SST and a press, install a new rear output shaft dust deflector.
SST 09316−20011, 09316 −60011 (09316−00011)
3. INSTALL OIL SEAL
Using SST and a hammer, drive in a new oil seal. SST 09316−60011 (09316 −00011, 09316−00031)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010