1996 TOYOTA LAND CRUISER Bolt

DI5Q5−02
W02056
1
2
3
4
567
8910 A
B
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−245
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
No.SymbolTerminal Name
A−Electrical Connection Check Mechanism
B−Electrical Connection Check Mechanism
1P−Squib  (Passenger)
2P+Squib  (Passenger)
3D−Squib  (Driver)
4D+Squib  (Driver)
5E1Ground
6E2Ground
7TcDiagnosis
8LASRS Warning Light
9IG2Power Source (IGN Fuse)
10ACCPower Source (CIG Fuse)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC−14
−
EMISSION CONTROL EXHAUST GAS RECIRCULATION (EGR) SYSTEM
1996 LAND CRUISER (RM451U)
21. REMOVE EGR VACUUM MODULATOR
22. REMOVE EGR VALVE
(a) Disconnect the vacuum hose from the EGR valve.
(b) Disconnect the engine wire from the clamp.
(c) Loosen the EGR pipe union nut.
(d) Remove the 2 nuts holding the EGR valve to the air intake
chamber.
(e) Using 2 nuts, remove the 2 stud bolts, EGR valve and gasket.
23. INSPECT EGR VALVE
Check for sticking and heavy carbon deposits.
If a problem is found, replace the valve.
24. REINSTALL EGR VALVE
(a) Using 2 nuts, temporarily install a new gasket, and EGR valve with the 2 stud bolts.
Torque: 9 N·m (90 kgf·cm, 78 in.·lbf)
(b) Install the 2 nuts holding the EGR valve to the air intake
chamber.
Torque: 18 N·m (180 kgf·cm, 13 ft·lbf)
(c) Tighten the union nut of the EGR pipe. Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(d) Connect the engine wire to the clamp.
(e) Connect the vacuum hose to the EGR valve.
25. REINSTALL EGR VACUUM MODULATOR
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1Q4−01
P05120A16078
1 Dot Mark
EM−4
−
ENGINE MECHANICAL VALVE CLEARANCE
507
Author: Date:
1996 LAND CRUISER (RM451U)
VALVE CLEARANCE
INSPECTION
HINT:
Inspect and adjust the valve clearance when the engine is cold.
1. DRAIN ENGINE COOLANT
2. REMOVE THROTTLE BODY (See page SF−45)
3. DISCONNECT ENGINE WIRE AND HEATER VALVE FROM COWL PANEL
(a) Remove the 2 bolts and disc onnect the ground strap and
engine wire.
(b) Remove the 2 bolts and disconnect the heater valve.
4. DISCONNECT HIGH −TENSION CORDS FROM SPARK
PLUGS (See page IG−1 )
5. REMOVE CYLINDER HEAD COVER
Remove the 13 bolts, cylinder head cover and gasket.
6. SET NO. 1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the timing mark ”0” of the timing chain cover.
(b) Check that the timing marks (1 and 2 dots) of the camshaft
drive and driven gears are in straight line on the cylinder
head surface as shown in the illustration.If not, turn the
crankshaft 1 revolution (360 °) and align the marks as
above.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM0494
−
ENGINE MECHANICAL VALVE CLEARANCE
EM−7
510
Author: Date:
1996 LAND CRUISER (RM451U)
9. Rear valves of No. 6 cylinder
ADJUST VALVE CLEARANCE
(a) Remove the distributor (See page IG−10).
(b) Remove the camshafts (See page EM−28).
(c) Remove the adjusting shim with a small screwdriver.
(d) Determine the replacement adjusting shim size by follow- ing the Formula or Charts:
Using a micrometer, measure the thickness of the
removed shim.
Calculate the thickness of a new shim so that the
valve clearance comes within specified value.
T ....... Thickness of removed shim
A ....... Measured valve clearance
N ....... Thickness of new shim
Intake: N = T + (A − 0.20 mm (0.008 in.))
Exhaust: N = T + (A − 0.30 mm (0.012 in.))
Select a new shim with a thickness as close as pos-
sible to the calculated value.
HINT:
Shims are available in 17 sized in increments of 0.05 mm
(0.0020 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.1299 in.).
(e) Place a new adjusting shim on the valve lifters.
(f) Install the camshafts (See page EM−54 ).
(g) Recheck the valve clearance.
(h) Install the distributor (See page IG−11 ).
10. REINSTALL CYLINDER HEAD COVER
(a) Install the gasket to the cylinder head cover.
(b) Install the cylinder head cover with the 13 bolts.
11. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS (See page IG−1 )
12. RECONNECT HEA TER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the ground strap and engine wire with the 2 bolts.
13. REINSTALL THROTTLE BODY (See page SF−48 )
14. REFILL RADIATOR WITH ENGINE COOLANT
15. CHECK AND ADJUST IGNITION TIMING (See page EM−10 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM0KT−06
EM−10
−
ENGINE MECHANICAL IGNITION TIMING
513
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION TIMING
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT TOYOTA HAND −HELD TESTER OR OBD II
SCAN TOOL
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester or OBD II scan tool to the DLC3.
(c) Please refer to the TOYOTA hand−held tester or OBD II scan tool operator’s manual for further details.
3. CONNECT TIMING LIGHT TO ENGINE
4. CHECK IDLE SPEED
(a) Race the engine speed at 2,500 rpm for approx. 90 se- conds.
(b) Check the idle speed. Idle speed: 650 ± 50 rpm
5. INSPECT AND ADJUST IGNITION TIMING
(a) Using SST, connect terminals TE1 and E1 of the DLC1. SST 09843−18020
(b) Using a timing light, check the ignition timing. Ignition timing: 3 ° BTDC @ idle
(Transmission in neutral position and A/C OFF)
(c) Loosen the hold−down bolt, and adjust by turning the dis-
tributor.
(d) Tighten the hold− down bolt, and recheck the ignition tim-
ing.
Torque: 18 N·m (180 kgf·cm, 13 ft·lbf)
(e) Remove the SST from the DLC1. SST 09843−18020
6. FURTHER CHECK IGNITION TIMING Ignition timing: 2 − 13° BTDC @ idle
(Transmission in neutral position and A/C OFF)
HINT:
The timing mark moves in a range between 2 ° and 13° .
7. DISCONNECT TIMING LIGHT FROM ENGINE
8. DISCONNECT TOYOTA HAND −HELD TESTER OR
OBD II SCAN TOOL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E9−01
−
ENGINE MECHANICAL TIMING CHAIN
EM−13
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE OIL
2. DRAIN ENGINE COOLANT
3. REMOVE ENGINE UNDER COVER
4. REMOVE RADIATOR (See page CO−14 )
5. DISCONNECT A/C COMPRESSOR AND BRACKET
(a) Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.
(b) Remove the 4 mounting bolts, and disconnect the com- pressor from the bracket.
HINT:
Put aside the compressor, and suspend it.
(c) Remove the 5 bolts and A/C compressor bracket.
6. REMOVE RADIATOR PIPE
(a) Disconnect the No. 2 radiator hose from the water inlet.
(b) Remove the 2 nuts and radiator pipe.
7. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
8. REMOVE CYLINDER HEAD (See page EM−28 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−14
−
ENGINE MECHANICAL TIMING CHAIN
1996 LAND CRUISER (RM451U)
9. DISCONNECT OIL COOLER PIPE BRACKET FROM
NO. 1 OIL PAN
10. REMOVE OIL LEVEL SENSOR
(a) Remove the 4 bolts and level sensor.
(b) Remove the gasket from the level sensor.
11. REMOVE BOLTS HOLDING NO.1 OIL PAN TO TRANS-
MISSION HOUSING
Remove the 6 bolts.
12. REMOVE NO. 2 OIL PAN (See page LU−5)
13. REMOVE NO. 1 OIL PAN (See page LU−5)
14. REMOVE CRANKSHAFT PULLEY
(a) Using SST, remove the pulley bolt. SST 09213−58012, 09330 −00021
(b) Remove the crankshaft pulley.
HINT:
If necessary, remove the pulley with SST. SST 09950−50010 (09951 −05010, 09952−05010,
09953 −05010, 09953 −05020, 09954−05020)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL TIMING CHAIN
EM−15
1996 LAND CRUISER (RM451U)
15. CHECK THRUST CLEARANCE OF OIL PUMP DRIVE
SHAFT GEAR
Using a dial indicator with lever type attachment, measure the
thrust clearance.
Standard thrust clearance:
0.040 − 0.160 mm (0.0016 − 0.0063 in.)
Maximum thrust clearance: 0.30 mm (0.0118 in.)
If the thrust clearance is greater than maximum, replace the oil
pump drive shaft gear and/or timing chain cover.
16. REMOVE DRIVE BELT IDLER PULLEY
Remove the bolt and idler pulley.
17. REMOVE TIMING CHAIN COVER
(a) Remove the 9 mounting bolts, 2 mounting nuts and drive belt adjusting bar.
(b) Remove the oil pump by prying the portions between the cylinder block and oil pump with a screwdriver.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and oil pump.
(c) Remove the O−rings from the oil pump.
(d) Remove the gasket from the oil pump.
18. REMOVE TIMING CHAIN AND CAMSHAFT TIMING GEAR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010