1996 TOYOTA LAND CRUISER Grease

Z13953
Example:CORRECT WRONG
Z13950
Example:
−
INTRODUCTION FOR ALL OF VEHICLES
IN−11
11
Author: Date:
1996 LAND CRUISER (RM451U)
(d) STEERING WHEEL PAD (with Airbag)
(1) When removing the steering wheel pad or handlinga new steering wheel pad, it should be placed with
the pad top surface facing up.
Storing the pad with its metallic surface facing up-
ward may lead to a serious accident if the airbag in-
flates for some reason. In addition do not store a
steering wheel pad on top of another one.
(2) Never measure the resistance of the airbag squib. (This may cause the airbag to deploy, which is very
dangerous.)
(3) Grease should not be applied to the steering wheel
pad and the pad should not be cleaned with deter-
gents of any kind.
(4) Store the steering wheel pad where the ambient temperature remains below 93 °C (200° F), without
high humidity and away from electrical noise.
(5) When using electric welding, first disconnect the air-
bag connector (yellow color and 2 pins) under the
steering column near the combination switch con-
nector before starting work.
(6) When disposing of a vehicle or the steering wheel pad alone, the airbag should be deployed using an
SST before disposal (See page RS−11).
Perform the operation in a safe place away from
electrical noise.
N01560
R05643 R06953 R06952
x
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z13952
Example:CORRECT WRONG
Z13951
Example:
IN−12
−
INTRODUCTION FOR ALL OF VEHICLES
12
Author: Date:
1996 LAND CRUISER (RM451U)
(e) FRONT PASSENGER AIRBAG ASSEMBLY
(1) Always store a removed or new front passenger air-
bag assembly with the airbag deployment direction
facing up.
Storing the airbag assembly with the airbag deploy-
ment direction facing down could cause a serious
accident if the airbag inflates.
(2) Never measure the resistance of the airbag squib. (This may cause the airbag to deploy, which is very
dangerous.)
(3) Grease should not be applied to the front passen- ger airbag assembly and the airbag door should not
be cleaned with detergents of any kind.
(4) Store the airbag assembly where the ambient tem- perature remains below 93 °C (200° F), without high
humidity and away from electrical noise.
(5) When using electric welding, first disconnect the air-
bag connector (yellow color and 2 pins) installed on
the assembly before starting work.
(6) When disposing of a vehicle or the airbag assembly
alone, the airbag should be deployed using an SST
before disposal (See page RS−25).
Perform the operation in a safe place away from
electrical noise.
o
R08766
R05648 R05649R06952
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R5−01
N06158
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
AC−33
1360
Author: Date:
1996 LAND CRUISER (RM451U)
COMPRESSOR AND MAGNETIC
CLUTCH
ON−VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET (See page AC−18 )
2. START ENGINE
Run the engine at 1,500 rpm.
3. INSPECT COMPRESSOR FOR METALLIC SOUND
Check if there is a metallic sound from the compressor when the
A/C switch is on.
If metallic sound is heard, replace the compressor assembly.
4. INSPECT REFRIGERANT PRESSURE (See page AC−5 )
5. STOP ENGINE
6. INSPECT VISUALLY FOR LEAKAGE OF REFRIGER- ANT FROM SAFETY SEAL
Using a gas leak detector, check for leakage of refrigerant.
If there is any leakage, replace the compressor assembly.
7. REMOVE MANIFOLD GAUGE SET (See page
AC−19 )
8. MAKE THESE VISUAL CHECKS:
(a) Leakage of grease from the clutch bearing.
(b) Signs of oil on the pressure plate or rotor. Repair or replace, as necessary.
9. INSPECT MAGNETIC CLUTCH BEARING FOR NOISE
(a) Start engine.
(b) Check for abnormal noise from near the compressor when the A/C switch is OFF.
If abnormal noise is being emitted, replace the magnetic clutch.
10. INSPECT MAGNETIC CLUTCH
(a) Disconnect the connector from the magnetic clutch.
(b) Connect the positive (+) lead from the battery to the termi-
nal on the magnetic clutch connector and the negative ( −)
lead to the body ground.
(c) Check that the magnetic clutch is energized.
If operation is not as specified, replace the magnetic clutch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE0150
Repair PointBroken
Wire
Marking Tape
BE0151
BE−44
−
BODY ELECTRICAL DEFOGGER SYSTEM
1996 LAND CRUISER (RM451U)
(f) The point where the voltmeter deflects from zero to sever-
al V is the place where the heat wire is broken.
HINT:
If the heat wire is not broken, the voltmeter indicates 0 V at the
positive (+) end of the heat wire but gradually increases to about
12 V as the meter probe is moved to the other end.
4. IF NECESSARY, REPAIR DEFOGGER WIRE
(a) Clean the broken wire tips with a grease, wax and silicone
remover.
(b) Place the masking tape along both sides of the wire to be
repaired.
(c) Thoroughly mix the repair agent (Dupont paste No. 4817
or equivalent).
(d) Using a fine tip brush, apply a small amount to the wire.
(e) After a few minutes, remove the masking tape.
(f) Do not repair the defogger wire for at least 24 hours.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−10
−
BODY FRONT DOOR
1996 LAND CRUISER (RM451U)
HINT:
At the time of reassembly, adjust the equalizer arm up to down
and tighten if where dimensions A and B, as shown are equal.
15. REMOVE DOOR GLASS
16. REMOVE WINDOW REGULATOR
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face and gears of the window regulator.
NOTICE:
Do not apply grease to the spring.
17. REMOVE LOCKING AND OPENING CONTROL LINK
18. REMOVE DOOR LOCK
HINT:
At the time of reassembly, apply adhesive to the 3 screws. Part No.08833 −00070, THREE BOND 1324 or equiva-
lent
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face of the door lock.
19. REMOVE DOOR OUTSIDE HANDLE
20. REMOVE DOOR LOCK CYLINDER
21. REMOVE DOOR SPEAKER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO2455
Cotton TapePanel
Cover
BO−16
−
BODY REAR DOOR
1996 LAND CRUISER (RM451U)
NOTICE:
Do not block the clip sealing with the tape.
11. REMOVE DOOR SPEAKER
12. REMOVE LINK PROTECTOR
13. REMOVE LOCKING LINK AND DOOR OPENING LINK
14. REMOVE DOOR GLASS RUN
15. REMOVE REAR LOWER FRAME
16. REMOVE QUARTER WINDOW GLASS WITH WEATH-
ERSTRIP
17. REMOVE DOOR GLASS
18. REMOVE WINDOW REGULATOR Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face and gears of the regulator.
NOTICE:
Do not apply grease to the spring.
19. REMOVE DOOR LOCK
HINT:
At the time of reassembly, apply adhesive to the 3 screws. Part No.08833 −00070, THREE BOND 1324 or equiva-
lent
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
At the time of reassembly, apply MP grease to the sliding sur-
face of the door lock.
20. REMOVE OUTSIDE HANDLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CL-01
-
BRAKE BRAKE MASTER CYLINDER
BR-13
1996 LAND CRUISER (RM451U)
REASSEMBLY
Reassembly is in the reverse order of disassembly.
NOTICE:
Apply lithium soap base glycol grease to the rubber parts indicated by t\
he arrows
(See page BR-9 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE FRONT BRAKE PAD
BR−23
1996 LAND CRUISER (RM451U)
HINT:
Apply disc brake grease to both sides of the inner anti −squeal
shims (See page BR−21 ).
(d) Install the 2 pads.
HINT:
Apply disc brake grease to the caliper indicated by the arrows
(See page BR−33 ).
NOTICE:
Do not allow oil or grease to get on the rubbing face.
6. INSTALL ANTI −RATTLE SPRING AND 2 PINS
7. INSTALL CLIP
8. INSTALL FRONT WHEEL
9. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010