1996 TOYOTA LAND CRUISER Grease

P05005
P08506
SST
P04518
P04970
SST
P08643
Cut Position
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−101
1996 LAND CRUISER (RM451U)
(b) If the timing chain cover is installed to the cylinder block:
(1) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
(2) Apply MP grease to a new oil seal lip.
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(3) Using SST and a hammer, tap in the oil seal until its
surface is flush with the timing chain cover edge.
SST 09316−60011 (09316 −00011, 09316−00051)
4. REPLACE CRANKSHAFT REAR OIL SEAL
HINT:
There are 2 methods ((a) and (b)) to replace the oil seal.
(a) If the rear oil seal retainer is removed from the cylinder block:
(1) Using a screwdriver and a hammer, tap out the oil
seal.
(2) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the rear oil seal edge.
SST 09223−15030, 09950 −70010 (09951−07150)
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(b) If the rear oil seal retainer is installed to the cylinder block:
(1) Using a knife, cut off the oil seal lip.
(2) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22572
P22574B13834
Drain Plug
Drain Plug
MA0621B13835
Lubricating Positions: 1. Spider2. Slide Yoke1
2 1
MA−8
−
MAINTENANCE CHASSIS
48
Author: Date:
1996 LAND CRUISER (RM451U)
7. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Remove the drain plug and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add new oil until it begins to run out of the filler hole.
Oil drade and viscosity: See step 5.
Oil capacity:
Transfer oil
1.7 liters (1.8 US qts, 1.5 lmp. qts)
Front differential oil (w/o Differential lock)
2.8 liters (3.0 US qts, 2.5 lmp. qts)
Front differential oil (w/ Differential lock)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
Rear differential oil
3.25 liters (3.4 US qts, 2.9 lmp. qts)
8. REPACK FRONT WHEEL BEARINGS (See pages SA−7 and SA−9 )
9. LUBE STEERING KNUCKLE CHASSIS AND PROPEL-
LER SHAFT
(a) Remove the screw plug from each steering knuckle and repack with lubricant.
Steering knuckle grease:
Molybdenum disulfide lithium base chassis grease
(NLGI No. 2)
(b) Reinstall the 2 screw plugs.
(c) Lubricate chassis components, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Grease grade:
Lithium base chassis grease (NLGI No. 2)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YW−01
−
PREPARATION BODY
PP−69
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
MP grease−−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR06O−02
Q10862
 Spider Grease Fitting
 Snap Ring
 Spider Bearing
Dust Cover
Grease Fitting Propeller Shaft
Flange Yoke
 Snap Ring
 Spider Bearing

Spider
Sleeve Yoke
N·m (kgf·cm, ft·lbf)
 Non− reusable part
Flange Yoke
Propeller Shaft
 Spider
Grease Fitting
Dust Cover

Spider Bearing

Snap Ring
Grease Fitting
Sleeve Yoke
: Specified torque
Flange Yoke
Flange Yoke
Front Propeller Shaft
74 (750, 54)
88 (900, 65)
74 (750, 54)
74 (750, 54)
74 (750, 54)
74 (750, 54)
88 (900, 65)
88 (900, 65)
88 (900, 65)
Rear propeller Shaft
 Spider
 Spider Bearing 
Snap Ring
Grease
Fitting
Grease Fitting
PR−2
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
850
Author: Date:
1996 LAND CRUISER (RM451U)
PROPELLER SHAFT ASSEMBLY
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR0310
PR06Q−01
PR0014
Matchmarks
PR0056
PR−4
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT FRONT AND REAR PROPELLER SHAFTS FOR DAMAGE OR RUNOUT
Using a dial indicator, check the runout of shafts. Maximum runout: 0.8 mm (0.031 in.)
If shaft runout is greater than maximum, replace the shaft.
2. REMOVE SLEEVE YOKE FROM PROPELLER SHAFT
Place matchmarks on the sleeve yoke and shaft.
(1) Pull out the sleeve yoke from the shaft.
(2) Remove the dust cover from the shaft.
3. INSPECT SPIDER BEARING
Check the spider bearings for wear or damage.
Check the spider bearing axial play by turning the yoke
with holding the shaft tightly.
Bearing axial play: Maximum 0.05 mm (0.0020 in.)
If necessary, replace the spider bearing.
4. INSERT SLEEVE YOKE INTO PROPELLER SHAFT
(a) Apply MP grease to the propeller shaft spline and sleeve yoke sliding surface.
(b) Align the matchmarks on the sleeve yoke propeller shaft.
(c) Install the propeller shaft into the sleeve yoke.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR06R−01
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
PR−5
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page PR−3 ).
HINT:
After installation, pump MP grease into each fitting with a grease gun until the grease begins to\
flow around
the oil seal.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04247
ColorDrit Mark
Bearing Cup
Drit Mark
Yoke
Q07142
Type A Type B X
610.0 mm (24.016 in.)
Y
545.0 mm (21.457 in.)
X
Y Differential
Side
Z00755
PR0081
Q07338
−
PROPELLER SHAFT SPIDER BEARING
PR−7
855
Author: Date:
1996 LAND CRUISER (RM451U)
5. SELECT SPIDER BEARING
Select the bearing according to whether or not there is a drill
mark on the yoke section.
YokeBearing (T ype A)Bearing (Type B)
w/ drill markw/ color mark (White)w/ color mark (Red)
No drill markNo color markNo color mark
HINT:
At time of the reassemble, there are 2 types of rear propeller
shafts, type A and type B. Referring to the illustration, measure
the distance between the welding points X and Y to identify
which of the 2 types is used for the vehicle.
6. INSTALL SPIDER BEARING
(a) Apply MP grease to a new spider and bearings.
NOTICE:
Be careful not to apply too much grease.
(b) Align the matchmarks on the yoke and flange.
(c) Fit the spider into the yoke.
(d) Using SST, install the bearings on the spider. SST 09332−25010
(e) Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal widths.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR0069
PR0031
PR−8
−
PROPELLER SHAFT SPIDER BEARING
856
Author: Date:
1996 LAND CRUISER (RM451U)
7. INSTALL SNAP RINGS
(a) Install 2 new snap rings of equal thickness which will allow
0 − 0.05 mm (0 − 0.0020 in.) axial play.
HINT:
Do not reuse the snap rings. Thickness of snap ring:
Front Propeller Shaft and Rear Propeller Shaft (Type
B)
ColorMarkThickness mm (in.)
−12.100 − 2.150
(0.0827 − 0.0846)
−22.150 − 2.200
(0.0846 − 0.0866)
−32.200 − 2.250
(0.0866 − 0.0886)
Brown−2.250 − 2.300
(0.0886 − 0.0906)
Blue−2.300 − 2.350
(0.0906 − 0.0925)
−62.350 − 2.400
(0.0925 − 0.0945)
−72.400 − 2.450
(0.0945 − 0.0965)
−82.450 − 2.500
(0.0965 − 0.0984)
Rear Propeller Shaft (Type A)
ColorThickness mm (in.)
−2.00 (0.0787)
Brown2.03 (0.0799)
Blue2.06 (0.0811)
−2.09 (0.0823)
(b) Using a hammer, tap the yoke until there is no clearance
between the bearing outer race and snap ring.
8. CHECK SPIDER BEARING (See page PR−4 )
Check that the spider bearing moves smoothly.
Check the spider bearing axial play.
Bearing axial play: Maximum 0.05 mm (0.0020 in.)
HINT:
Install a new spider bearing on the flange side in the pro-
cedure described above.
When replacing the spider bearing, be sure that the
grease fitting assembly hole is facing in the direction
shown in the illustration.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010