1996 LINCOLN CONTINENTAL ESP

Use only recommended fuels, lubricants, fluids,
and service parts conforming to Ford
specifications. Motorcraft parts are designed and
built to provide the best performance in your
vehicle. Using these parts for replacement is your
assurance that Ford-buflt quality stays in your
vehicle.
NOTE: Always dispose of used automotive fluids
in a responsible manner. Follow your community's
standards for disposing of these types of fluids.
Call your local recycling center to find out about
recycling automotive fluids.
Accident Damage
Should your vehicle suffer accident damage
requiring new sheet metal or plastic replacement
parts, be sure your repair shop uses only genuine
Ford replacement parts.
While imitation body parts may appear similar to
genuine Ford parts on the surface, differences in
232quality become obvious when both are subjected to
standard Ford quality tests.
Ford tests indicate that you should be concerned with
the quality of the fit and finish, corrosion resistance
and structural integrity of these imitation replacement
parts, and how their use will affect your warranty.
How Can You Protect Yourself?.
Before any repair work begins, tell your adjuster that
you want your vehicle repaired using only genuine
Ford body parts. If the adjuster refuses, contact your
insurance agent for help. If your agent and your
insurance company refuse to repair your vehicle with
original factory parts, you should contact your state
insurance commissioner, the National Highway Traffic
Safety Administration or a local consumer protection
agency.
In Canada, contact provincial insurance
commissioners, Transport Canada or local consumer
protection groups.

Precautions When Servicing Your
Vehicle
Be especially careful when inspecting or servicing
your vehicle. Here are some general precautions
for your safety: Do not work on a hot engine. The engine
cooling fan may come on unexpectedly. Always
turn the engine off and let it cool./!\ WARNINGThe cooling fan is automatic and may comeon at any time. Always disconnect thenegative terminal of the battery beforeworking near the fan. If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair. Do not work on a vehicle in an enclosed space
with the engine running, unless you are sure you
have enough ventilation. Never get under a vehicle while it is supported by a
jack only. If you must work under a vehicle, use
safety stands. Keep all lit cigarettes and other smoking materials
away from the battery and all fuel-related parts.
If you disconnect the battery, the engine must
“relearn" its idle conditions before your vehicle will
drive properly. To find out how the engine does this,
see Battery in this chapter.
Working with the engine off.
1. Set the parking brake fully and make sure that the
gearshift is securely latched in P (Park).
2.Remove the key from the ignition after you turn
the engine off.
233

/!\ WARNINGIf you do not use the proper fuel cap, thepressure in the fuel tank can damage the fuelsystem or cause it to work improperly in acollision.NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer warranty
may be void for any damage to the fuel tank and/or
fuel system.
Choosing the Right Fuel
Use only PREMIUM UNLEADED FUEL in your
vehicle. Using leaded fuel is prohibited by federal
law. Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
Octane recommendations
The 4.6L engine is designed to operate on
premium fuel with an octane rating of 91 or
higher. Regular fuel with an octane rating of 87
240may be used if necessary. For optimum
performance, premium fuel is recommended.Typical octane rating label
In some parts of the country, "premium" grade fuels
are sold with octane ratings of less than 91,
especially in high altitude areas. It is recommended
that you use only those "premium" fuels with an
octane rating of 91 or higher.
Do not be concerned if your vehicle sometimes
knocks lightly when you drive up a hill or when you
accelerate. However, see your dealer or a qualified
service technician if persistent, heavy knocking
occurs because this can damage the engine.

your engine cooling system. Follow the
recommended service interval for changing your
engine coolant.
NOTE: When you change or add engine coolant, it
is important to maintain your engine coolant
concentration between 40% (-11°F [-24°C]) and
60% (-62°F [-52°C]), depending on your local
climate conditions. Below 40% you will lose freeze
protection; above 60% your engine may overheat
on a warm day.
NOTE: Less than 40% of coolant concentration
may cause engine corrosion and overheating. Plain
water may be used in an emergency only. Replace
it with the specified coolant as quickly as possible.
NOTE: The use of an improper coolant may void
your warranty for the engine cooling system. Use
only a premium, nationally recognized brand name
engine coolant. Do not use alcohol, methanol
antifreeze or engine coolant mixed with alcohol or
methanol antifreeze. If you do not use the proper
250coolant, the aluminum engine on your vehicle will
corrode.
Ford Motor Company expressly authorizes the Ford
Rotunda engine coolant recycling process and
chemicals. Use only Ford Rotunda recycled engine
coolant or an equivalent recycled engine coolant that
is certified by the supplier to meet Ford specification
ESE-M97B44-A.
NOTE: Always dispose of used automotive fluids
in a responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about
recycling automotive fluids.
Use Ford Premium Cooling System Fluid E2FZ-
19549-AA (in Canada, Motorcraft CXC-8-B) or an
equivalent engine coolant that meets Ford
Specification ESE-M97B44-A.

Treadwear
The treadwear grade is a comparative rating based
on the wear rate of the tire when tested under
controlled conditions on a specified government test
course. For example, a tire graded 150 would wear
one and one-half (1 1/2) times as well on the
government course as a tire graded 100. The
relative performance of tires depends upon the
actual conditions of their use, however, and may
depart significantly from the norm due to variations
in driving habits, service practices and differences in
road characteristics and climate.
Traction A B C
The traction grades, from highest to lowest, are A, B,
and C, and they represent the tire's ability to stop on
wet pavement as measured under controlled
conditions on specified government test surfaces of
asphalt and concrete. A tire marked C may have
poor traction performance. Warning: The traction
grade assigned to this tire is based on braking(straightahead) traction tests and does not include
cornering (turning) traction.
Temperature A B C
The temperature grades are A (the highest), B, and
C, representing the tire's resistance to the generation
of heat and its ability to dissipate heat when tested
under controlled conditions on a specified indoor
laboratory test wheel. Sustained high temperature
can cause the material of the tire to degenerate and
reduce tire life, and excessive temperature can lead
to sudden tire failure. The grade C corresponds to a
level of performance which all passenger car tires
must meet under the Federal Motor Vehicle Safety
Standard No. 109. Grades B and A represent higher
levels of performance on the laboratory test wheel
than the minimum required by law. Warning: The
temperature grade for this tire is established for a tire
that is properly inflated and not overloaded.
Excessive speed, underinflation, or excessive
259

If the vehicle has not been driven and the fluid level
is above the bottom dimple on the dipstick, do not
add fluid. Recheck the fluid level after your vehicle
has reached normal operating temperature.
Normal operating temperature is reached after
driving approximately 20 miles (30 km). The fluid
level should be within the crosshatched area on the
dipstick.
NOTE: If the vehicle has been operated for an
extended period at high speeds, driven in city traffic
during hot weather, or has been pulling a trailer, the
vehicle should be turned off for about 30 minutes to
allow the fluid to cool before checking.
Adding Automatic Transaxle Fluid
Before adding any fluid, be sure that the correct
type will be used. Correct type is shown on the
dipstick.
Add fluid in 1/2 pint (.25L) increments through the
filler tube to bring the level to the correct area on
262the dipstick. DO NOT OVERFILL. If the level is
above the top hole on the dipstick, excess fluid
should be removed by a qualified technician.
NOTE: Always dispose of used automotive fluids
in a responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to,find out about
recycling automotive fluids.Automatic over transaxle fluid dipstick

/! WARNINGAlways replace a fuse with one that has thespecified amperage rating. Using a fuse witha higher amperage rating can cause severewire damage and could start a fire.5.Align the edge of the cover with the edge of
the fuse panel and push the cover up until it
latches.
Even after you replace a fuse, it will continue to
blow if you do not find what caused the overload.
If the fuse continues to blow, have your electrical
system checked.
Lights and Bulb Replacement
It is a good idea to check the operation of the
following lights ftequently: headlamps high-mount brakelamp tail lamps brakelamps hazard flasher turn signals side markers license plate lamp
The alignment of your headlamps should be
checked if: oncoming motorists frequently signal you to
turn off your vehicle's high beams when you do
not have the high beams on the headlamps do not seem to give you enough
light to see clearly at night
277

Emission Control System
Your vehicle is equipped with three (3) catalytic
converters which are used to enable your vehicle to
comply with applicable exhaust emissions
requirements./!\ WARNINGExhaust leaks may result in the entry ofharmful and potentially lethal fumes into thepassenger compartment. Under extremeconditions excessive exhaust temperaturescould damage the fuel system, the interiorfloor covering, or other vehicle components,possibly causing a fire.To make sure that the catalytic converters and the
other emissions control parts continue to work
properly: Use only premium unleaded fuel.
284 Avoid running out of fuel. Do not turn off the ignition while your vehicle is
moving, especially at high speeds. Do not push start your vehicle. Have the services listed in the Maintenance
Schedule and Record booklet performed according
to the specified schedule. The scheduled
maintenance services are required because they are
considered essential to the life and performance of
your vehicle and to its emissions system.
In general, maintenance, replacement, or service of
the emissions control devices or systems in your new
Ford Motor Company vehicle or engine may be
performed at your expense by any automotive repair
establishment or individual using automotive parts
equivalent to those which your vehicle or engine was
originally equipped.