1996 FORD E SERIES Page 3

203
*
[DR09400( ALL)01/95]
Driving
%*
[DR09500( ALL)04/95]
When to usej(Overdrive)
*
[DR09600( ALL)04/95]
This is the normal driving position. As the
vehicle picks up speed, automatic upshifts to
second, third and fourth gears will occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been
pressed. The transmission will shift into the
correct gear when the right speed is achieved,
for the accelerator pedal position you have
chosen.
*
[DR09700( ALL)03/94]
When to use Drive
*
[DR09800( ALL)05/95]
You will note that there isn't a drive position on
your gearshift indicator. However, you will find
a Transmission Control Switch and an indicator
light labeled ªOverdriveº located on the end of
the gearshift lever. Press this switch and the
word ªOFFº will illuminate on the shift lever
knob. With the word ªOFFº illuminated, the
transmission will operate in gears one through
three. Operating in the Overdrive ªOFFº mode
gives more engine braking than Overdrive and
is useful for descending hills or when towing.
[DR09850( ALL)04/95]
quarter page art:0020771-C
Transmission Control Switch and indicator light (located
on the gearshift lever)
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

213 [DR24940( E )03/91]
one third page art:0020836-A
Parking Brake
[DR24942( E )03/91]
To release the parking brake, press the service
pedal with your right foot and hold it while you
push the parking brake pedal down firmly with
your left foot.
[DR24945( E )04/94]
one third page art:0020893-A
Parking brake (Commercial stripped chassis only)
[DR24946( E )04/94]
To release the parking brake for Commerical
Stripped Chassis vehicles, press the service brake
pedal with your right foot and pull the parking
brake release lever.
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

221
*
[DR29551( ALL)03/91]
Each additional item of equipment affects how
much cargo a vehicle can carry. If a vehicle is
overloaded, performance will suffer and service
concerns may arise.
*
[DR29601(BEF )04/95]
The following is a typical example of a Safety
Compliance Certification Label and an
explanation of how this information should be
used:
[DR29801( E )12/91]
half page art:0020151-E
Safety Compliance Certification Label
*
[DR29950(BEF )06/92]
Do not use the sample numbers on the Safety
Compliance Certification Label shown. Use the
actual numbers from your vehicle certification
label.
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

226
*
[DR31550( ALL)03/91]
q
Weigh your vehicle as you customarily
operate the vehicle without cargo.
*
[DR31601( ALL)03/91]
q
Subtract the total weight of passengers, driver
and optional equipment added by the factory,
dealer or aftermarket supplier to determine
how much cargo weight you can carry.
[DR31660( E )03/94]
half page art:0021097-A
Sample label
*
[DR31702( ALL)03/91]
If you suspect that your payload is excessive,
have your vehicle weighed at a highway weigh
station or appropriate commercial facility. Weigh
the total vehicle and trailer (if applicable), then
separately weigh the vehicle at the front and
rear wheels. And finally, weigh the trailer
separately if applicable.
*
[DR31751( ALL)03/91]
Use this chart to perform your calculations.
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

246
*
[RE02200( ALL)05/95]
RWARNING
Do not connect the end of the second
cable to the negative (-) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
*
[RE02300( ALL)06/93]
one third page art:0020262-C
Attaching jumper cables
*
[RE02500( ALL)03/95]
Jump-Starting
*
[RE02600( ALL)03/95]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[RE02700( ALL)03/95]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[RE02800( ALL)03/95]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

249 [RE05975( E )02/95]
three fourths page art:0020839-C
The spare tire location and assembly
*
[RE06050( E )03/91]
To stow spare tire:
*
[RE06150( E )10/94]
1. Insert the jack handle or lug nut wrench into
the actuator hole and turn counterclockwise
until the cable/retainer is extended for
insertion into the wheel.
*
[RE06200( E )10/94]
2. Install the retainer through wheel center
with valve stem facing up.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

251 [RE15445(E )05/95]
RWARNING
On E-Super Duty vehicles, the parking
brake is on the transmission. Therefore,
the vehicle will not be prevented from
moving when a rear wheel is lifted, even
if the vehicle is in Park and the parking
brake is applied. Be sure to block both
directions of the wheel that is diagonally
opposite to the wheel that is being lifted.
If the vehicle slips off the jack, someone
could be seriously injured.
*
[RE15550(BEF )05/95]
2. Get out the spare tire and jack.
[RE16300( E )01/89]
The jack, jack handle and lug nut wrench are
stowed as shown below.
[RE16400( E )05/91]
one third page art:0020289-D
Jack handle and wrench stowage
*
[RE16800(BEF )12/91]
3. Use the tapered end of the lug nut wrench
to unscrew wheel ornaments attached by
retaining screws. Remove any wheel trim.
Insert the tapered end of the lug nut wrench
behind wheel covers or hubcaps and twist
off.
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996

253 [RE18551(E )11/89]
one third page art:0020296-A
Jacking point (All models except E-Super Duty)
[RE18600(BE )11/89]
one third page art:0021527-A
Jacking point (E-Super Duty)
[RE18900( E )12/91]
one third page art:0020298-B
Instructions for jacking a wheel Ð All models
File:11ltree.ex
Update:Wed Apr 17 08:42:44 1996