1996 FORD E SERIES Page 3

338 [SV42190( E )03/91]Non-fuse panel circuit protection
[SV42195( E )02/95]
twelve pica chart:0020853-E%*
[SV42200( ALL)06/95]
Checking and Replacing Fuses
*
[SV42300( ALL)02/95]
If you need to check a fuse, follow these steps:
[SV42950( E )02/91]
1. You can access the fuse panel through the
steering column lower opening. Remove the
cover using the quick release fasteners.
*
[SV43300( ALL)06/95]
2. On the fuse panel cover, find the number of
the fuse you want to check. The diagram on
the cover tells you where to locate the fuse
on the panel.
*
[SV43400( ALL)06/95]
3. Check the fuse to see if it is blown. Look
through the clear side of the fuse to see if
the metal wire inside is separated. If it is,
the fuse is blown and should be replaced.
*
[SV43500( ALL)06/95]
quarter page art:0020405-A
The side view of a fuse
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

341
*
[SV45800(BEF )03/95]
Headlamp Bulb
[SV45850( E )12/91]
Hi series (Aerodynamic)
*
[SV45900(BEF )01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV46000(BEF )05/95]
RWARNING
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp
the bulb only by its plastic base and do
not touch the glass. The oil from your
hand could cause the bulb to break the
next time the headlamps are operated.
*
[SV46050(BEF )12/91]
NOTE: If the bulb is accidently touched, it
should be cleaned with rubbing
alcohol before being used.
*
[SV46100(BEF )01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
*
[SV46200(BEF )03/91]
one third page art:0020406-B
Parts of a headlamp
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

342
*
[SV46300(BEF )03/95]
Removing the headlamp bulb
*
[SV46400(BEF )01/95]
1. Make sure that the headlamp switch on the
instrument panel is in the OFF position.
[SV46550( E )04/95]
2. Lift the hood and fix in up position using
prop rod.
[SV46600( E )04/95]
3. Bend back slightly and lift up on the two
metal tabs while holding the lamp to vehicle.
This will release the lamp from the installed
position.
[SV46650( E )05/91]
one third page art:0020844-B
Removing/Installing the headlamp bulb
[SV46750( E )04/95]
4. Remove the bulb retaining ring by turning it
1/8 of a turn to free it from the socket. Then
slide the ring off the plastic base. Keep the
ring. You must use it again to hold the new
bulb in place.
[SV46850( E )04/95]
5. Carefully remove the bulb assembly from its
socket by gently pulling it rearward without
turning.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

344 [SV47460( E )03/91]E-150 Ð E-350 with cargo lamp attached
[SV47470( E )03/91]
To remove/install or replace a bulb:
[SV47480( E )03/91]
1. Remove the two screws that secure the
Hi-mount stop lamp/cargo lamp and lift the
assembly from the vehicle.
[SV47490( E )03/91]
2. After removing the two screws that secure
the lens, remove the cargo lamp lens.
[SV47501( E )03/91]
3. Remove the two screws attaching the cargo
lamp to the Hi-mount stop lamp.
[SV47510( E )03/91]
4. Remove or replace the burned-out bulb(s) in
the Hi-mount stop lamp.
[SV47520( E )03/91]
5. To install a bulb, reverse the procedures
above.
[SV47530( E )12/91]
half page art:0020852-B
Replacing the stop lamp bulb
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

369 [QI02500( E )05/95]
full page art:0021505-B
Warning label locations
File:15ltqie.ex
Update:Wed Apr 17 08:37:06 1996

370 [QI02800( E )06/93]
full page art:0021025-AFront exterior view
File:15ltqie.ex
Update:Wed Apr 17 08:37:06 1996

371 [QI03400( E )06/93]
full page art:0021031-A
Rear exterior view
File:15ltqie.ex
Update:Wed Apr 17 08:37:06 1996

372 [QI04000( E )05/94]
full page art:0021037-CEntrance view
File:15ltqie.ex
Update:Wed Apr 17 08:37:06 1996