1995 RENAULT MEGANE SCENIC lights

LOWER STRUCTURE
Rear end pillar lower reinforcement
PRE4109
41E
INTRODUCTION
The replacement of this part is a complementary
operation to the rear end cross member.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with welded nuts.
PARTS CONCERNED (thickness in mm) :
1Rear end pillar lower reinforcement 1
2Rear end cross member 0.8
3Body side lining 0.7
4Rear end pillar lining 1
5Rear floor 0.7
6Rear side member 1.2
7Lights mounting 0.7
8Rear end pillar lining 1
41-8

UPPER REAR STRUCTURE
Rear wing panel
INTRODUCTION
This part may be replaced in two ways:
• by part section as a basic operation for a rear
side impact (see diagram),
• completely, as a complementary operation to
the roof.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- striker plate reinforcement,
- pin to be welded 3 x2.9,
- soundproofing,
- bumper mounting reinforcement assembly.
PRE4415
44A
or
PARTS CONCERNED (thickness in mm) :
1Wing panel 0.8
2Rear quarter panel lining 0.7
3Sill panel closure panel 1.5
4Rear pillar reinforcement 1
5Rear outer wheel arch 0.7
6Rear upper side drip moulding 1
7Lights moulding 0.7
8Rear end pillar lining 1
9Rear end panel 1
10Rear end pillar lower reinforcement 1
44-1

UPPER REAR STRUCTURE
Rear lights mounting
PRE4416
44B
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PARTS CONCERNED (thickness in mm) :
1Lights mounting 0.7
2Rear upper side drip moulding 1
3Rear end pillar lining 1
4Rear end panel 1
254b01-15380
A
CAA11536-2R7
12
44-10

UPPER REAR STRUCTURE
Rear lights mounting
44B
B
TOK14644-1R2
1
2 3
C
CAB11539R5
31
D
CAE11546-8R2
5
1 2
E
CAB11539R5
51
F
G
CAA11536-2R3
1
2
CAE11546-8R2
4
1 5
44-11

UPPER REAR STRUCTURE
Upper side drip moulding
44C
INTRODUCTION
The replacement of this part is a complementary
operation to the rear wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- balancer ball joint,
- parcel shelf mounting.
PARTS CONCERNED (thickness in mm) :
1Rear upper side drip moulding 1
2Lights mounting 0.7
3Rear end pillar lining 1
4Rear end pillar lower reinforcement 1
PRE4423
44-12

UPPER REAR STRUCTURE
Rear end panel
PRE4422
44H
INTRODUCTION
The replacement of this part is a basic operation
for a rear impact.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with rear end panel lower reinfor-
cement.
PARTS CONCERNED (thickness in mm) :
1Rear end panel 1
2Body side lining 0.7
3Lights mounting 0.7
4Rear end pillar lower reinforcement 1
5Rear end cross member 0.8
6Rear end panel inner reinforcement 1
7Tailgate striker plate reinforcement 1.2
8Rear wing panel 1
254h01-15369
or
A
TOK14644-1R1
1
34
44-31

NON-SIDE OPENING ELEMENT
MECHANISMS
Tailgate lock barrel
Rear screen wiper motorPage
Contents
WINDOWS
Rear door sliding window
Rear screen
Rear quarter panel window
EXTERIOR PROTECTION
Rear bumper
55
54
Mechanisms and
accessories
54-1
54-3
54-6
55-1
52
52-1
52-3
Number plate lights mounting 56-1 EXTERIOR ACCESSORIES
56
59-1
59-3 Front seat belts
Rear seat belts
59INTERIOR SAFETY ACCESSORIES

EXTERIOR ACCESSORIES
Number plate lights mounting
56A
Remove:
- the two mounting bolts (A),
- the tailgate lock barrel (see section 52A).
REMOVAL
Remove the inner tailgate trim (see section 73A).
15418R2
Using unpicking pliers, remove the two clips (B)
and release the lights mounting.
Remove the two connectors (C) for the number
plate lights.
15407R
PRE5610
IMPORTANT : before refitting the support, ensure
the seal (D) and where it fits on the tailgate are
clean.
Ensure the clips are present (E).
56-1