1995 RENAULT MEGANE SCENIC tailgate

EXTERIOR ACCESSORIES
Number plate lights mounting
56A
Remove:
- the two mounting bolts (A),
- the tailgate lock barrel (see section 52A).
REMOVAL
Remove the inner tailgate trim (see section 73A).
15418R2
Using unpicking pliers, remove the two clips (B)
and release the lights mounting.
Remove the two connectors (C) for the number
plate lights.
15407R
PRE5610
IMPORTANT : before refitting the support, ensure
the seal (D) and where it fits on the tailgate are
clean.
Ensure the clips are present (E).
56-1

Contents
Page
Upholstery and trim
Boot carpet
Headlining
Front rear quarter panel lining
Rear rear quarter panel lining
Lower rear quarter panel lining
Wheel arch lining71-1
71-2
71-5
71-6
71-7
71-8
73-1 Tailgate lining INTERIOR BODY TRIM
NON-SIDE OPENING ELEMENTS TRIM
71
73

INTERIOR BODY TRIM
Headlining
71B
After removing the front and rear head restraints,
protect the seats and remove:
- the four door seals,
- the boot seal,
- the windscreen pillar linings (A),
- the upper centre pillar linings (B),
- the front rear quarter panel linings (C) (see
section 71C),
- the rear rear quarter panel linings (D) (see sec-
tion 71D),
- the sun visors and their retaining clips,
- the grab handles and their blanking plugs for
the driver’s position,
- the roof console (E),
- the courtesy lights,
- the rear speaker grilles (F),
- the tailgate mounting plugs (G),
- the centre retaining clip (H),
- the third rear seat belt (see section 59B).
INTRODUCTION
This headlining is bonded to the roof using a single pot adhesive used for bonding windows.
The rear side edges of the headlining are held in place with velcro (1).
REMOVAL
PRE7113
PRE7114
71-2

INTERIOR BODY TRIM
Headlining
71B
NOTES:
The headlining does not need to be released to re-
move the plugs (I).
Remove the surrounding trim and the rear clips
and plugs to release the velcro strips " (J).
Pull the headlining slightly to one side.
Remove the stop (K).
Remove the blanking plug (I). Gently pull the rear edges of the headlining to re-
lease the velcro strips at the side (1).
Using equipment for manually removing bonded
windows (pulling handle, unpicking tool, cutting
wire), working progressively from the front to the
rear, cut the beads of adhesive between the hea-
dlining and the roof panel (two persons required
for this operation).
Remove the headlining through the tailgate.
15419R
15408R
IMPORTANT: during this operation, take care not
to cut the foam wedge at the rear of the cut-out
for the roof console.
Do not fold the headlining during this operation
if it is not to be renewed.
71-3

INTERIOR BODY TRIM
Headlining
71B
Flatten the beads of adhesive on the roof panel
and on the headlining in the case of a removal /
refitting operation using a cutting tool such as a
mastic knife.REFITTING
Apply adhesive to the headlining as shown oppo-
site, observing the dimensions for positioning the
beads of adhesive below:
A = 155 mm B = 125 mm
C = 445 mm D = 275 mm
E = 300 mm F = 270 mm
G = 130 mm
NOTE: Use a single pot polyurethane adhesive of
the additional 310 ml cartridge type.
Bring the headlining in through the tailgate.
Centre it in relation to the cut outs for the sun vi-
sors and the grab handles.
Flatten the headlining against the roof panel in
the bonding areas at the rear side retaining clips
(A) (see previous pages).
First fit the sun visor retaining clips and the rear
tailgate mounting plugs (G) and (H) (see previous
pages).
Refit the vehicle trim.
15421R
71-4

NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining
73A
Remove:
- the two mounting bolts (A) for the closing
handle,
- the retaining clips (B), (to remove these clips,
turn each clip a quarter turn using a flat blade
screwdriver),
- the lining.
REMOVAL
15417R
PRE7305
73-1

48
NON-SIDE OPENING ELEMENTS
Tailgate

48
NON-SIDE OPENING ELEMENTS
Tailgate