1995 RENAULT MEGANE SCENIC dimensions

UPPER SIDE STRUCTURE
Partial sill panel
43J
PRE4309
II I I
NN N N
TT T T
RR R R
OO O O
DD D D
UU U U
CC C C
TT T T
II I I
OO O O
NN N N
The changing of this part is a basic operation to
be carried out in the event of a side impact.
It is obtained by cutting the sill panel observing
the dimensions.
CC C C
OO O O
MM M M
PP P P
OO O O
SS S S
II I I
TT T T
II I I
OO O O
NN N N

OO O O
FF F F

TT T T
HH H H
EE E E

RR R R
EE E E
PP P P
LL L L
AA A A
CC C C
EE E E
MM M M
EE E E
NN N N
TT T T

PP P P
AA A A
RR R R
TT T T
Part only.
43-19

GLAZING
Front door window
Place the rear upper stop (8) in contact with the
lower window pad and tighten it.
Tighten the rear guide shoe bolt (2).
Tighten the window mounting bolts (3).
54
Place the front upper stop (8) in contact with the
lower window pad and tighten it.
Close and lock the hood.
Close the door.
Position the window at the dimensions:
D = 55 mm (window/weatherstrip)
E = 10 mm (window/frame)
Visually check that the window is aligned with the
hood seals.
12470R
12277-3R
12277-3R1
Tighten the rear slider bolt (4).
Open the door.
Push the rear slider gently towards the exterior of
the door.
Tighten the nut (4).
Open and close the window several times. Check
that the window is positioned correctly (aligned)
in relation to the hood seals.
Tightening torque of all mounting bolts 8 N.m.
54-4

40
GENERAL
Dimensions and engines

40
GENERAL
Sub-frame dimensions

40
GENERAL
Sub-frame dimensions

Contents
GENERAL
Dimensions
Engine and equipment
Identification
Using symbols
Key to symbols
Description of parts (exploded)
Opening clearances40-1
40-2
40-2
40-3
40-5
40-6
40-7
LOWER STRUCTURE
41-1
41-2
41-5
41-7
41-8
41-11
41-14Page Page40
41
Sheet metal work
UPPER SIDE STRUCTURE43
AAbsorber support mounting
BRear floor base
CRear floor base support
DRear floor base front stiffener
ERear end pillar lower reinforcement
FRear end cross member assembly
GRear floor unit
43-1 ATop of bodyNON-SIDE OPENING ELEMENTS
48
TOP OF BODY
SIDE OPENING ELEMENTS45
47
45-1
45-6
45-8
45-10 ARoof
BRoof acoustic cross member
CRoof bow
DRoof rear cross member
47-1
48-1 ATailgate ARear door panel UPPER REAR STRUCTURE
44
44-1
44-10
44-12
44-15
44-20
44-21
44-27
44-31 ARear wing panel
BRear lights mounting
CUpper side drip moulding
DRear pillar reinforcement
ERear inner wheel arch
FRear quarter panel lining assembly
GOuter wheel arch
HRear end panel

GENERAL
Dimensions
40
15309R
Dimensions in metres
* Unladen.
40-1

INTERIOR BODY TRIM
Headlining
71B
Flatten the beads of adhesive on the roof panel
and on the headlining in the case of a removal /
refitting operation using a cutting tool such as a
mastic knife.REFITTING
Apply adhesive to the headlining as shown oppo-
site, observing the dimensions for positioning the
beads of adhesive below:
A = 155 mm B = 125 mm
C = 445 mm D = 275 mm
E = 300 mm F = 270 mm
G = 130 mm
NOTE: Use a single pot polyurethane adhesive of
the additional 310 ml cartridge type.
Bring the headlining in through the tailgate.
Centre it in relation to the cut outs for the sun vi-
sors and the grab handles.
Flatten the headlining against the roof panel in
the bonding areas at the rear side retaining clips
(A) (see previous pages).
First fit the sun visor retaining clips and the rear
tailgate mounting plugs (G) and (H) (see previous
pages).
Refit the vehicle trim.
15421R
71-4