1995 LAND ROVER DISCOVERY warning

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system.
·To ensure the brake system efficiency is not
impaired the following warnings must be
adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK / TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Do not fill reservoir above maximum line

70BRAKES
2
REPAIR BRAKE SYSTEM BLEED
Service repair no - 70.25.02
The following method for bleeding the hydraulic brake
system applies to both ABS and NON ABS vehicles.
Preparation
WARNING: Before bleeding the brake
system refer to general brake service
practice.
See General Brake Service
Practice
·During bleed procedure, brake fluid level
must not be allowed to fall below the MIN
level. Keep reservoir topped to the MAX level.
·To bleed the hydraulic circuits four bleed
nipples are provided, one at each caliper.
·There are two methods by which air can be
removed from the braking system:-
1. MANUAL BLEED PROCEDURE.
2. PRESSURE BLEED PROCEDURE.
Pressure bleed procedure
Purpose designed equipment for pressure filling and
bleeding of hydraulic systems may be used on Land
Rover vehicles. The equipment manufacturer's
instructions must be followed and the pressure must
not exceed 4.5 bar.
Manual bleed procedure
Equipment required
·Clean glass receptacle
·Bleed hose
·Wrench
·Approx 2 litres brake fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Master cylinder bleed
1.Disconnect battery negative lead.
2.Depress brake pedal fully and slowly 5 times.
3.Release the pedal and wait for ten seconds.
4.Air bubbles will rise into the reservoir during
these instructions.
5.Repeat instructions until a firm resistance is felt
at the pedal.
Complete circuit bleed
1.Disconnect battery negative lead.
2.Fit bleed hose to any caliper bleed screw.
3.Dip free end of bleed hose into brake fluid in
bleed bottle.
4.Open bleed screw of caliper.
5.Depress brake pedal fully several times until fluid
is clear of air bubbles.
6.Keeping pedal fully depressed, tighten bleed
screw, then release pedal.
7.Repeat the above procedure on remaining three
calipers.
8.Fit all bleed screw protection caps.
9.Check/top-up fluid level when bleeding is
complete.
See Fluid Level Check / Top-Up

70BRAKES
4
REPAIR MASTER CYLINDER NON ABS
Service repair no - 70.30.08 - Remove
Service repair no - 70.30.09 - Repair
- Lucas Girling - Type 25.4mm AS/AS
WARNING: This master cylinder is not
suitable to be fitted on vehicles with
antilock brake systems.
Before starting repair refer to general brake service
practice.
See General Brake Service Practice
Remove
1.Disconnect battery negative lead.
2.Place a suitable container under master cylinder
to catch brake fluid from cylinder when brake
pipes are disconnected.
3.Thoroughly clean immediate area around all
outlet ports. Remove each brake pipe, sealing
each pipe and outlet port with suitable plugs to
prevent ingress of foreign matter.
4.Disconnect electrical plug from low fluid switch
on reservoir cap.
5.Remove two nuts securing master cylinder to
servo unit remove also spring and plain washers.
6.Detach master cylinder from servo, remove
reservoir cap and drain brake fluid into a suitable
container.Repair
7.Thoroughly clean master cylinder and inspect
outer surfaces for damage and condition, renew
complete assembly if necessary.
8.Using two soft jaws, clamp master cylinder
flange in a suitable vice. Remove water ingress
'O' ring seal from master cylinder to servo flange
and discard.
9.Grip outside of transfer housing with a suitable
pair of pliers, carefully pull, working pliers in a
backwards and forwards rocking motion to ease
housing off master cylinder. Discard housing and
vacuum seal.

70BRAKES
18
REPAIR SENSORS - FRONT
Service repair no - 70.65.32
CAUTION: If a sensor is removed for any
reason, a NEW sensor bush and seal must
be fitted.
Remove
1.Disconnect battery negative lead.
2.Disconnect required sensor electrical
connection, located on inner wing [fender] panel.
3.Remove sensor lead from clips.
4.Clean area surrounding sensor to prevent
ingress of dirt. Using a suitable lever pry sensor
from mounting bush.
5.Release harness cable ties, remove sensor lead
from vehicle.
6.Remove top swivel retaining bolts complete with
brake jump hose and sensor seal. Remove
sensor bush.
Refit
7.Insert new sensor bush and seal.
8.Refit brake jump hose bracket, coat bolts with
Loctite 270.
9.Lightly coat new sensor using EP 90 oil. Push
sensor through bush until it contacts exciter ring.
Sensor will be 'knocked back' to correct position
when vehicle is driven.
10.Secure sensor lead in original position.
11.Reconnect sensor electrical connection.
12.Drive vehicle to ensure ABS warning light is
extinguished.
SENSOR RINGS
The rear sensor ring is assembled to the rear brake
disc to form part of the rear hub assembly.
See
REAR AXLE AND FINAL DRIVE, Repair, Rear Hub
Assembly
The front sensor ring is a toothed ring on the axle
shaft which forms part of the front stub axle assembly.
See FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing ABS

BRAKES
19
REPAIR SENSORS - REAR
Service repair no - 70.65.31
CAUTION: If a sensor is removed for any
reason, a NEW sensor bush must be fitted.
Remove
1.Disconnect battery negative lead.
2.Disconnect sensor electrical connections,
located above rear axle.
3.Remove sensor from its locating clip.
4.Remove bolts securing mudshield.
5.Using a suitable lever, pry sensor from mounting
bush.
6.Release harness cable ties, remove sensor lead
from vehicle.
7.Remove sensor bush.
Refit
8.Fit new sensor bush.
9.Lightly grease new sensor using silicone grease.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
10.Push sensor through bush until it touches exciter
ring. Sensor will be 'knocked back' to correct
position when vehicle is driven.
11.Secure harness in position.
12.Reconnect sensor electrical connection.
13.Drive vehicle to ensure ABS warning light is
extinguished.STOP LIGHT SWITCH ABS
Service repair no - 86.65.51
Remove
1.Turn ignition off. Disconnect battery negative
lead.
2.Remove lower trim panel.
3.Disconnect multiplug to switch.
4.Depress brake pedal access front of switch.
5.Pull sleeve and plunger of switch FULLY
forward.
6.Remove switch rearwards
NOTE: If switch is difficult to release,
check sleeve is FULLY forward.
Refit
7.Pull sleeve and plunger of switch fully forward.
8.Depress brake pedal, fit switch. Ensure retaining
clips are FULLY located.
9.Hold switch firmly in place, pull brake pedal back
fully to set switch.
10.Reconnect battery and turn ignition on.
11.Check switch operation by slowly depressing
brake pedal and checking that the switch clicks
twice.
12.Check stop lamps go off when pedal is released.
13.Recheck switch is securely fitted.
14.Operation may be checked using Testbook.

70BRAKES
22
REPAIR MODULATOR UNIT
Service repair no - 70.65.45
WARNING: New modulator units are
supplied in a shock absorbing pack
marked with a use by date. The new
modulator will contain hydraulic brake fluid within
the valve block and all ports plugged.
Modulator units must be handled with care the
following must be avoided:- any impact, use of
compressed air on any of the hydraulic ports,
removing plugs to connection ports before fitting
unit.
Remove
1.Refer to the illustration of brake components
ABS. For details of modulator unit and hydraulic
pipe connections to it.
See Brake
Components ABS
2.Refer to general brake service practice.See
General Brake Service Practice
3.Check new modulator unit is packaged in
accordance with the WARNING above.
4.Disconnect battery negative lead.
5.Remove the two electrical plugs.
6.Identify 8 pipe to modulator connections for
correct reassembly.
7.Disconnect 8 pipe unions.
8.Remove nuts securing modulator to mounting
bracket.
9.Remove modulator unit.
10.Remove mounting bushes and cup.
Refit
11.Fit mounting bushes and cup to new modulator.
12.Fit modulator unit to mounting bracket.
13.Fit 8 pipes to modulator connections. Pipes
mustbe connected to correct port. Tighten to
15Nm.
14.Bleed the complete hydraulic system.See
Brake System Bleed
15.Check system function using the 'Testbook'
diagnostics
16.Test operation of brakes.ELECTRONIC CONTROL UNIT ABS
Service repair no - 70.65.01
Remove
For location of the ECU.
See Description and
operation, ABS Components
1.Disconnect battery negative lead.
2.Remove retaining bolt and lower alarm system
ECU and relay mounting bracket into passenger
footwell.
3.Remove two screws and detach ECU complete
with harness plug from mounting bracket.
4.Release ECU plug retaining clip.
5.Move plug in direction of arrow and release
hooked end of plug from retaining post.
Refit
6.Reconnect ECU harness plug ensuring that it is
firmly located and retaining clip secures plug.
7.Reverse removal procedure.

WHEELS AND TYRES
1
REPAIR GENERAL INFORMATION
WARNING: This is a multi- purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures.
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels.The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim.
See
Tyre Fitting
WARNING: Do not fit an inner tube to an
alloy wheel.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment.
See Fault
diagnosis, Tyre Wear Chart
if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration below.
When the tread has worn to a remaining depth of 1.6
mm the indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration below.

74WHEELS AND TYRES
6
REPAIR WHEELS
Remove
WARNING: The parking brake acts on
transmission, not rear wheels, and may
not hold vehicle when jacking unless
following procedure is used. If one front wheel
and one rear wheel is raised no vehicle holding or
braking effect is possible. Wheels MUST be
chocked in all circumstances.
Apply parking brake, select 'P' or a gear in main
gearbox and engage low gear in transfer box.
1.Loosen five wheel nuts.
2.Using a suitable trolley jack raise vehicle and
place on axle stands.
See INTRODUCTION,
Information, Jacking
3.Remove wheel nuts and carefully withdraw
wheel over studs.Refit
4.Ensure that retaining studs and nuts are clean.
5.Alloy wheels: Lightly coat wheel mounting spigot
face with a suitable anti-seize compound to
minimise possibility of adhesion between wheel
and spigot face.
6.Refit wheel taking care not to damage stud
threads. (Do not apply oil)
7.Fit wheel nuts and turn by hand for at least three
full threads before using any form of wheel
wrench.
8.Tighten nuts as much as possible using a
suitable wrench.
9.Lower vehicle and finally tighten nuts to correct
torque sequence shown. Alloy wheels and steel
wheels:
130Nm.