1995 LAND ROVER DISCOVERY bulb

ELECTRICAL
17
REPAIR REAR LIGHT UNIT
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Disconnect wiring harness multi-plug from light
unit.
4.Remove retaining nuts and withdraw light unit
from rear of vehicle.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure. Ensure that the
rubber seal is seated correctly.STOP, REVERSING, FOG GUARD BULBS
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Turn bulb holder anti-clockwise to release.
4.Remove bulb.
NOTE: On vehicles fitted with rear air
conditioning remove access panel
housing rear loadspace light to gain
access.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure.

86ELECTRICAL
18
REPAIR REAR LIGHTS, BUMPER MOUNTED
Service repair no - 86.41.42
Remove
1.From behind bumper disconnect light plugs.
2.Unscrew two retaining nuts and remove light unit
from bumper.
Refit
3.Reverse removal procedure.
NOTE: The black lead plug fits into the
direction indication light, the white lead
plugs into the tail light, the bulb holder
being colour coded red.DIRECTION INDICATOR, TAIL LIGHT BULBS
Service repair no - 86.41.43
Remove
1.Turn bulb holder anti-clockwise to release from
light unit.
2.Push and twist the bulb to remove.
Refit
3.Reverse removal procedure.

ELECTRICAL
19
REPAIR NUMBER PLATE LIGHTS
Service repair no - 86.40.86
Remove
1.Remove two screws and withdraw light unit.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.DOOR EDGE LIGHT
Service repair no - 86.40.35
Remove
1.Pry lens from housing.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.

86ELECTRICAL
20
REPAIR HIGH MOUNTED STOP LIGHT
Service repair no - 86.41.35
Remove
1.Remove two screws and lift off light reflector
body.
2.Unscrew retaining nut and remove lens unit from
rear door glass.
Refit
3.Reverse removal procedure.STOP LIGHT BULB
Service repair no - 86.40.87
Remove
1.Remove reflector body.
2.Turn bulb holder anti-clockwise to release from
light unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure.

ELECTRICAL
21
REPAIR INTERIOR LIGHT
Service repair no - 86.35.14
Remove
1.Pry out light unit from roof location.
2.Disconnect light switch plug.
Refit
3.Reverse removal procedure.
Bulb Removal.
1.Pry out interior light lens.
2.Remove bulb.
Refit
3.Reverse removal procedure.REAR LOADSPACE LIGHT
Service repair no - 86.41.40
Remove1.Pry light unit from trim panel.
2.Disconnect wiring leads.
3.Remove bulb.
Refit
4.Reverse removal procedure.

86ELECTRICAL
22
REPAIR SIDE REPEATER LIGHT
Service repair no - 86.50.59
Remove
1.Push the lens to the right and then pull outward
to detach lens and bulb holder from the panel.
2.Turn lens anti-clockwise and remove from bulb
holder.
3.Pull bulb from holder.
Refit
4.Reverse removal procedure.BUMPER MOUNTED SIDE LIGHT
Service repair no - 86.50.59
Remove
1.From behind bumper turn holder anti-clockwise
and release from light unit.
2.Pull bulb from holder.
Refit
3.Reverse removal procedure.

86ELECTRICAL
30
REPAIR INSTRUMENT ILLUMINATION AND WARNING
LIGHT BULBS
Service repair no - 86.45.48 - Instrument
Service repair no - 86.45.61 - Warning light
Remove
1.Remove binnacle.
See Instrument binnacle
2.Identify bulb to be replaced.
NOTE: If faulty bulb is not accessible,
remove screws securing circuit board and
carefully ease circuit board aside.
3.Rotate bulb holder anti-clockwise, withdraw bulb
holder and remove bulb.Refit
4.Fit new bulb to holder.
CAUTION: Ensure bulb of correct wattage
and type is fitted.
5.Reverse removal procedure.

ELECTRICAL
31
REPAIR MAIN PRINTED CIRCUIT
Service repair no - 88.20.19
Remove
1.Remove instrument cowl.
See Instrument
cowl and illumination board
2.Remove circuit board.See Circuit board
3.Remove illumination and warning lamp bulbs.
4.Remove 13 screws securing main printed circuit,
remove circuit.
Refit
5.Position main printed circuit to binnacle.
6.Ensure screw holes in instruments are aligned
with holes in binnacle, fit and tighten screws.
7.Reverse removal procedure. 1 and 2.