1995 LAND ROVER DISCOVERY transmission

INTRODUCTION
11
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (AC)....................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position (CTP)......................................
Canister purge valve (CANPV)....................................
Data link connector (DLC)...........................................
Diagnostic trouble code (DTC).....................................
Distributor ignition (DI).................................................
Engine control module (ECM)......................................
Engine coolant level (ECL)...........................................
Engine coolant temperature (ECT)..............................
Engine coolant temperature sensor (ECTS)................
Engine speed (RPM)....................................................
Evaporative emission system (EVAP)..........................
Engine fuel temperature sensor (EFTS)......................
4th gear, 3rd gear etc. (4GR, 3GR)..............................
Fuel pump (FP)............................................................
Fan control module (FCM)...........................................
Generator (GEN)..........................................................
Ground (GND)..............................................................
Heated oxygen sensor (H02S)....................................
Idle air control (IAC)......................................................
Idle air control valve (IACV).........................................
Ignition control module (ICM).......................................
Inertia fuel shutoff (IFS)................................................
Inertia fuel shutoff switch (IFSS)..................................
Intake air temperature (IAT).........................................
Malfunction indicator lamp (MIL)..................................
Manifold vacuum zone (MVZ)......................................
Mass air flow sensor (MAFS).......................................
Multiport fuel injection (MFI)........................................
On board diagnostic (OBD)..........................................
Open loop (OL)............................................................
Park/neutral position (PNP).........................................
Park/neutral position switch (PNPS)............................
Programmable read only memory (PROM)..................
Relay module (RM)......................................................
Service reminder indicator (SRI)..................................
Solid state relay module (SSRM).................................
Three way catalytic converter (TWC)..........................
Throttle body (TB)........................................................
Throttle position sensor (TPS)......................................
Torque converter clutch (TCC)....................................
Transmission range (TR)..............................................
Transmission range selector (TRS).............................
Vehicle speed sensor (VSS)........................................
Wide open throttle (WOT)............................................OLD TERM (ACRONYM)
Throttle pedal (-)..........................................................
Air cleaner (-)...............................................................
Air conditioning (AC)....................................................
Battery plus, bat +, bat feed (B+).................................
Closed loop (-).............................................................
Closed throttle, idle position (-)....................................
Charcoal canister purge valve (-).................................
Serial link (-)................................................................
Fault code (-)...............................................................
Electronic ignition (-)....................................................
Electronic control unit (ECU)........................................
Coolant level (-)...........................................................
Coolant temperature (temp).........................................
Coolant temperature thermistor (-)..............................
Engine speed (rev/min)................................................
Evaporative loss system (ELC)...................................
Fuel temperature thermistor (-)....................................
Fourth gear, 3rd gear (-)..............................................
Fuel pump (-)...............................................................
Condenser fan timer (-)................................................
Alternator (-)................................................................
Ground, earth (B-)........................................................
Lambda (02) sensor (-)................................................
Idle speed control (ISC)................................................
Stepper motor (-).........................................................
Ignition module (-)........................................................
Inertia switch (-)...........................................................
Inertia switch (-)...........................................................
Intake temperature/ambient temperature (-)................
EFI warning lamp (-)....................................................
Manifold depression, vacuum (-).................................
Air flow meter (-)..........................................................
Electronic fuel injection (EFI).......................................
Fault code display unit (-)............................................
Open loop (-)...............................................................
Park or neutral (-).........................................................
Start inhibit switch (-)...................................................
Chip, PROM (PROM)...................................................
Relay (-).......................................................................
Check engine light (-)...................................................
Control unit (-)..............................................................
Catalyst, catalytic converter (CAT)..............................
Throttle housing (-)......................................................
Throttle potentiometer (-).............................................
Direct drive clutch (DDC)..............................................
Transmission gear (-)...................................................
Shift lever, shifter (-)....................................................
Road speed transducer (-)...........................................
Full throttle, wide open throttle (WOT).........................

01INTRODUCTION
12
INFORMATION VEHICLE IDENTIFICATION NUMBER (VIN)
The Vehicle Identification Number and the
recommended maximum vehicle weights are stamped
on a plate located under the bonnet [hood] riveted to
the front of the engine compartment.
Vehicle Identification Number Plate (UK, Australia,
R.O.W., Europe)
A.Build date (Australia). Type approval
B.VIN (17 digits)
C.Maximum permitted laden weight for vehicle
D.Maximum vehicle and trailer weight
E.Maximum road weight-front axle
F.Maximum road weight-rear axle
The number is also stamped on the right side of the
chassis forward of the spring mounting turret.
Vehicle Identification Number Plate (Saudi Arabia)
A.Year of manufacture
B.Month of manufacture
C.Maximum vehicle weight
D.Maximum road weight-front axle
E.Maximum road weight-rear axle
F.VIN (17 digits)
The vehicle identification number identifies the
manufacturer, model range, wheel base, body type,
engine, steering, transmission, model year and place
of manufacture. The following example shows the
coding process.
SALWorld manufacturer identifier
LHRange Rover or
LJDiscovery
GClass 100 inch
B2 door
F300 Tdi or
VV8i Petrol
85 speed LHD or
75 speed RHD
M1995 MY
ASolihull site

GENERAL SPECIFICATION DATA
9
INFORMATION TRANSMISSION 3.9 V8i
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Clutch
Make and type Borg and beck diaphram type..................................................................
Clutch plate diameter 266.5mm........................................................
Automatic gearbox
Type ZF4HP Four speed and reverse with fluid torque converter.....................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output, front....................................................................
and rear drive permanently engaged via a lockable
differential.
Propeller shafts
Type
Front Tubular 51mm diameter.................................................................................
Front - Catalyst vehicles Solid bar 28.6mm diameter...................................................
Rear Tubular 51mm diameter.................................................................................
Universal joints Open type Hookes O3EHD.................................................................
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
Front axle
Type Spiral bevel, enclosed constant velocity joints, fully.................................................................................
floating shafts
Angularity of universal joint on full lock 32° ............................
Ratio 3.54:1.................................................................................

GENERAL SPECIFICATION DATA
21
INFORMATION TRANSMISSION - 300 Tdi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Automatic gearbox
Type ZF4HP Four speed and reverse with fluid torque converter.....................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential

04GENERAL SPECIFICATION DATA
24
INFORMATION FUEL SYSTEM - Mpi
Electronic fuel injection data
See ENGINE TUNING DATA, Information, Engine............................................
- Mpi - 2.0 Litre
Fuel Pump:
Make/Type A.C. Rochester/Electric immersible.......................................................................
Pump pressure 3.2 bar.................................................................
Delivery at 3 bar pressure & 12V (min) 64 litre/h............................
Regulated pressure range 3.0 ñ 0.2 bar................................................
Fuel pump delivery pressure 2.3 - 2.5 kgf/cm
2............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
COOLING SYSTEM - Mpi
Pressure cap 15lbf/in
2(1.03 bar) (system pressure) ....................................................................
Thermostat 88 ÊC.......................................................................
CLUTCH - Mpi
Type Diaphragm spring, hydraulically operated.................................................................................
Adjustment Self adjusting.......................................................................
Clutch plate diameter 215.13 mm.......................................................
TRANSMISSION - Mpi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential
Overall ratios (final drive): In high transfer In low transfer
Fifth 4.146:1.................................................................................. 9.761:1
Fourth 4.989:1............................................................................... 11.746:1
Third 7.518:1................................................................................. 17.701:1
Second 11.479:1............................................................................. 27.109:1
First 17.884:1.................................................................................. 42.109:1
Reverse 18.463:1............................................................................ 43.472:1

MAINTENANCE
9
MAINTENANCE
CHECK CONDITION OF DRIVE BELT - V8i - Tdi -
Mpi
RENEW - V8i - Tdi
Renew drive belt V8i.See ENGINE, Repair, Drive
Belt Renew
Renew drive belt Tdi.See ENGINE, Repair, Drive
Belt Renew
RENEW - Mpi
1.Check condition of drive belt, renew a belt that
shows signs of wear, splitting or oil
contamination.
2.Check belt length indicator, belt must be
renewed before indicator reaches R.H. end of
slot.
3.Use 15mm ring wrench on bolt and hold
tensioner pulley fully clockwise.
4.Release drive belt from tensioner pulley and
remove ring wrench.
5.Remove belt from between pulleys.
6.Clean drive belt pulley grooves and ensure
grooves are not damaged.
7.Fit new drive belt around pulley, except
tensioner pulley, ensuring all grooves are
correctly engaged.
8.Hold tensioner pulley fully clockwise and fit drive
centrally around tensioner pulley.
RENEW ANCILLARY DRIVE BELTS
CHECK/TOP UP AUTOMATIC TRANSMISSION
FLUID LEVEL
NOTE: Transmission fluid level is checked
when fluid is cold with engine idling in
neutral.
1.Ensure vehicle is on level ground.
2.Check fluid level registers between MAX and
MIN marking on dipstick.

10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

Tdi
3
REPAIR ENGINE
Service repair no - 12.41.01
Remove
CAUTION: Seal all exposed pipe ends
against ingress of dirt after disconnection.
1.Park vehicle on level ground and apply park
brake.
2.Disconnect battery negative lead.
3.Remove bonnet [hood].
See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.If air conditioning is fitted, remove RH footwell
side trim panel and disconnect harness multiplug
from relay.
5.Disconnect the two engine harness multiplugs
on LH side of footwell.
6.Remove engine harness grommet from
bulkhead and move harness into engine bay.
7.Release battery positive lead from retaining clip
at base of suspension turret.
8.Remove Radiator Assembly.
See COOLING
SYSTEM, Repair, Radiator
9.Discharge air conditioning system.See AIR
CONDITIONING, Adjustment, Refrigerant
Recovery Recycling Recharging
Remove retaining bolts and disconnect both pipe
adaptors from rear of compressor.
10.Remove rocker cover insulation.
11.Disconnect cyclone hose from air cleaner hose.
12.Remove air cleaner hose from turbocharger.
13.Remove feed pipe/hose from turbocharger and
intercooler.
14.Disconnect heater hoses from cylinder head and
heater rails.
15.Remove bolt securing transmission breather
pipe clip to cylinder head; move breather pipes
aside.
16.Disconnect inlet and outlet hoses from power
steering pump.
17.Disconnect bypass hose from thermostat
housing.
18.Release bypass hose from retaining clips on
front timing cover.
19.Remove split pin securing inner throttle cable to
injector pump.
20.Depress tags on outer cable adjusting nut,
remove cable from mounting bracket, and move
aside.
21.If automatic transmission is fitted, release
kickdown cable from injector pump and mounting
bracket.