1995 LAND ROVER DISCOVERY oil pressure

04GENERAL SPECIFICATION DATA
2
INFORMATION Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0,018-0,041 mm...................................
Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Molybdenum barrel faced.....................................................
No 2 compression ring Tapered and marked 'T' or 'TOP'.....................................................
Width of compression rings 1,478-1,49 mm..............................................
Compression ring gap 0,40-0,65 mm......................................................
Oil control ring width 3,0 mm.........................................................
Oil control ring rail gap 0,38-1,40 mm.....................................................
Camshaft
Location Central...........................................................................
Bearings Tin - aluminium...........................................................................
Number of bearings 5..........................................................
Drive Chain 9,52 mm pitch x 54 pitches..................................................................................
TappetsHydraulic-self-adjusting ...........................................................................
Valves
Length: Inlet 116,59-117,35 mm..................................
Exhaust 116,59-117,35 mm...........................
Seat angle: Inlet 45°to 45 1/2° ..................................
Exhaust 45°to 45 1/2° ...........................
Head diameter: Inlet 39,75-40,00 mm..................................
Exhaust 34,226-34,480 mm...........................
Stem diameter: Inlet 8,664-8,679 mm..................................
Exhaust 8,651-8,666 mm...........................
Stem to guide clearance: Inlet 0,025-0,066 mm..................................
Exhaust 0,038-0,078 mm...........................
Valve lift (Inlet and Exhaust) 9,49 mm............................................
Valve spring length fitted 40,4 mm at pressure of 29,5 kg..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Eccentric rotor...................................................................
Oil pressure 2.75 bar (40 lb/in
2) at 2500 rev/min with engine at ......................................................................
running temperature
Oil filter-internal Wire screen, pump intake filter.................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

04GENERAL SPECIFICATION DATA
4
INFORMATION Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Nitrided steel barrel faced.....................................................
No 2 compression ring Tapered spherical barrel marked 'TOP'.....................................................
Width of compression rings 1.478 - 1.49 mm.............................................. 0.0582 - 0.0587 in
(Top) 1.21 - 1.23 mm................................ 0.0476 - 0.0484 in
Compression ring gap 0.40-0.65 mm...................................................... 0.0157 - 0.0256 in
(Top) 0.3 - 0.5 mm................................ 0.0118 - 0.0197 in
Oil control ring type Aclonoform..........................................................
Oil control ring width 3.0 mm......................................................... 0.1181 in
Oil control ring rail gap 0.38-1.40 mm..................................................... 0.0150 - 0.0551 in
Camshaft
Location Central...........................................................................
Bearings Non serviceable...........................................................................
Number of bearings 5..........................................................
Drive Chain 9.52 mm pitch x 54 pitches..................................................................................
Camshaft End Float 0.076 - 0.355 mm......................................................... 0.003 - 0.014 in
TappetsHydraulic self-adjusting ...........................................................................
Valves
Length: Inlet 116.59 - 117.35 mm.................................. 4.590 - 4.620 in
Exhaust 116.59 - 117.35 mm........................... 4.590 - 4.620 in
Seat angle: Inlet 46°-46°25' ..................................
Exhaust 46°-46°25' ...........................
Head diameter: Inlet 39.75 - 40.00 mm.................................. 1.565 - 1.575 in
Exhaust 34.227 - 34.48 mm........................... 1.3475 - 1.3575 in
Stem diameter: Inlet 8.664 - 8.679 mm.................................. 0.3411 - 0.3417 in
Exhaust 8.651 - 8.666 mm........................... 0.3406 - 0.3412 in
Stem to guide clearance: Inlet 0.025 - 0.066 mm.................................. 0.0010 - 0.0026 in
Exhaust 0.038 - 0.078 mm........................... 0.0015 - 0.0031 in
Valve lift (Inlet and Exhaust) 9.94 mm............................................ 0.3913 in
Valve spring length fitted 40.4 mm (1.59 in) at pressure of 29.5 kg (65 lb)..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Rotor...................................................................
Oil pressure 2.11 to 2.81 kg/cm
2(30 to 40 psi) at 2400 rev/min with ......................................................................
engine warm
Oil filter-internal Wire screen, pump intake filter in sump................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................

04GENERAL SPECIFICATION DATA
10
INFORMATION COOLING SYSTEM 3.9 V8i
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti-freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler.
Fan and viscous coupling assembly 11 blade axial flow 433mm diameter.................................
Pump type Centifugal, impellor, belt driven.........................................................................
Thermostat opening 88 degrees..........................................................
Expansion tank cap pressure 15 p.s.i. (system pressure)............................................
STEERING
Power steering box
Make/type Adwest Varamatic - worm and roller box........................................................................
Ratio Variable: straight ahead 19.3:1 on lock 14.3:1.................................................................................
Steering wheel turns, lock-to-lock 3.375....................................
Steering pump
Make/type -V8i ZF - Unicorn.................................................................
Make/type - Mpi & Tdi Hobourn-Eaton series 500......................................................
Steering geometry
Steering wheel diameter 405mm..................................................
Steering wheel diameter airbag model 400mm.............................
Toe-out measurement 0 to 2mm toe out......................................................
Toe-out included angle 0Ê to 0Ê 16'.....................................................
Camber angle 0Ê.................................................................. Check with vehicle in static..............
unladen condition, that is, vehicle
with water,
Castor angle 3Ê..................................................................... oil and five gallons of fuel. Rock..............
the vehicle up and down at the
front to allow
Swivel pin inclination static 7Ê............................................... it to take up a position..............

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

04GENERAL SPECIFICATION DATA
22
INFORMATION ENGINE - Mpi - 2.0 LITRE
Type 20 T4 - 16 valve twin overhead camshaft.................................................................................
Cylinder arrangement 4 in line.......................................................
Bore 84.45 mm.................................................................................
3.325 in
Stroke 89.00 mm...............................................................................
3.504 in
Capacity 1994 cm
3...........................................................................
121.68 in3
Firing order 1-3-4-2.......................................................................
Compression ratio 10 : 1............................................................
Oil pump
Outer rotor to body clearance 0.05 to 0.10 mm..........................................
Inner rotor tip clearance 0.025 to 0.12 mm...................................................
Outer rotor end float 0.03 to 0.08 mm.........................................................
Oil pressure relief valve
Spring free length 42.0 mm.............................................................
Cooling system
Starts to open 82 to 86°C ...................................................................
Thermostat fully open 88°C .......................................................
Open travel A 9 mm...................................................................
Camshaft
Camshaft end-float 0.06 to 0.25 mm...........................................................
Bearing clearance 0.060 to 0.094 mm............................................................
Service limit 0.15 mm.............................................................
Timing belt tensioner
Spring free length 57.5 to 58.5 mm.............................................................
Cylinder head
Longitudinal warp - maximum 0.1 mm.................................
Transverse warp - maximum 0.1 mm...................................
Diagonal warp - maximum 0.1 mm......................................
Cylinder head height 135.0 to 135.1 mm...............................................
Valve springs
Free length 46.25 mm.......................................................................
Fitted length 37.0 mm.....................................................................
Load at fitted length 255±12 N ..........................................................
Load at valve open length 560±22.5 N ................................................

05ENGINE TUNING DATA
6
INFORMATION ENGINE - Mpi - 2.0 LITRE
Type/Capacity 20 T4/1994 cm
3..................................................................
Firing order 1-3-4-2.......................................................................
Compression ration 10 : 1..........................................................
Idle speed:
Controlled by ECM 875±50 rev/min ...........................................................
Exhaust gas Co content:
- Catalyst 0.5% Max. Not adjustable..................................................................
- Non Catalyst 1,0±25% adjustable using Testbook .........................................................
Ignition
Knock sensor ADU 8229...................................................................
Crankshaft sensor ADU 7340............................................................
Ignition Coils
Type NEC 10049.................................................................................
Primary resistance at 20°C 0.4 to 0.61 ohm..............................................
Consumption - engine idling 0.25 to 0.75 amp.............................................
Spark Plugs
Type/Gap GSP 6662 -0,85 mm.........................................................................
Multipoint Fuel Injection
Type Indirect multipoint injection with engine control module.................................................................................
using speed/density method of air flow measurement.
Fuel pressure regulator MKW 10011....................................................
Fuel pump delivery pressure 2.3 - 2.5 bar............................................
Throttle potentiometer voltage
- Throttle closed 0 - 1 Volt......................................................
- Throttle open 4 - 5 Volts.........................................................
MEMS engine control module MKC 10121..........................................
95 RON minimum -UNLEADEDfuel
CAUTION: Do not use LEADED fuel as it will
damage the catalyst. Serious damage to the
engine may occur if a lower octane number fuel
than that recommended is used.

GENERAL FITTING REMINDERS
5
INFORMATION JOINTS AND JOINT FACES
1.Always use correct gaskets where they are
specified.
2.Use jointing compound only when
recommended. Otherwise fit joints dry.
3.When jointing compound is used, apply in a thin
uniform film to metal surfaces; take great care to
prevent it from entering oilways, pipes or blind
tapped holes.
4.Remove all traces of old jointing materials prior
to reassembly. Do not use a tool which could
damage joint faces.
5.Inspect joint faces for scratches or burrs and
remove with a fine file or oil stone; do not allow
removed material or dirt to enter tapped holes or
enclosed parts.
6.Blow out any pipes, channels or crevices with
compressed air, fit new 'O' rings or seals
displaced by air blast.FLEXIBLE HYDRAULIC PIPES, HOSES
1.Before removing any brake or power steering
hose, clean end fittings and area surrounding
them as thoroughly as possible.
2.Obtain appropriate plugs or caps before
detaching hose end fittings, so that ports can be
immediately covered to exclude dirt.
3.Clean hose externally and blow through with
airline. Examine carefully for cracks, separation
of plies, security of end fittings and external
damage. Reject any hose found faulty.
4.When refitting hose, ensure that no unnecessary
bends are introduced, and that hose is not
twisted before or during tightening of union nuts.
5.Containers for hydraulic fluid must be kept
absolutely clean.
6.Do not store brake fluid in an unsealed
container. It will absorb water, and fluid in this
condition would be dangerous to use due to a
lowering of its boiling point.
7.Do not allow brake fluid to be contaminated with
mineral oil, or use a container which has
previously contained mineral oil.
8.Do not re-use brake fluid bled from system.
9.Always use clean brake fluid to clean hydraulic
components.
10.Fit a cap to seal a hydraulic union and a plug to
its socket after removal to prevent ingress of dirt.
11.Absolute cleanliness must be observed with
hydraulic components at all times.
12.After any work on hydraulic systems, inspect
carefully for leaks underneath the vehicle while a
second operator applies maximum pressure to
the brakes (engine running) and operates the
steering.