1995 LAND ROVER DISCOVERY oil pressure

12ENGINE
4
FAULT DIAGNOSIS 3.Are fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit
YES - Suspect valves held open by hydraulic
tappets due to high oil pressure.
See
Engine Oil Pressure Test
4.Is oil pressure high?
YES - Remove oil filter and cooler adaptor and
check pressure relief valve strainer gauze
for blockage and that the relief valve is
not stuck closed.
See Description and
operation, Description
NO - Carry out cylinder compression tests to
determine condition of head gaskets and
valves.
See Cylinder Compression -
Test
5.Are cylinder compressions satisfactory?
NO -
See Repair, Cylinder Heads - Renew
YES - Check brake vacuum connections.See
BRAKES, Description and operation,
Brake Servo Unit
Check heater/ventilation unit vacuum connections.
See HEATING AND VENTILATION, Description and
operation, Heating and Ventilation Unit
If problem is not diagnosed: Continue.
6.Are the brakes binding?
YES - Investigate cause of binding.
NO - Continue.
7.Automatic Transmission only. Is the Torque
Converter and Transmission operating correctly?
Carry out Road test, Static tests and Stall tests
to determine condition of Automatic
transmission.
If problem is not diagnosed: repeat tests starting at 1.Engine backfires into exhaust system
1.Are there any leaking joints/connections or holes
in the exhaust system?
YES -
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust System
Complete
NO - Continue.
2.Is distributor fitted correctly, HT leads in correct
firing order and routed correctly?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
4.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
See Repair, Cylinder Heads - Renew
If problem is not diagnosed: repeat tests starting
at 1.

V8i
9
REPAIR FRONT COVER GASKET
Service repair no - 12.65.04
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys
2.Remove water pump pulley.
3.Release distributor cap clips.
4.Release plug leads from plugs and clips.
5.Place cap and leads to one side.
6.Turn engine until No. 1 piston is at T.D.C.
7.Check position of rotor arm.
8.Remove fixings securing power steering pump
bracket to water pump bracket.
9.Remove power steering pump bracket from
water pump.
10.Remove clips securing wiring to generator
tensioner.
11.Disconnect distributor feed wire.
12.Pivot power steering pump away from front
cover, tighten pivot to retain in position.
13.Disconnect vacuum pipe from distributor.
14.Remove water pump bottom hose.
15.Disconnect oil pressure switch.
16.Disconnect heater hose at water pump.
17.Remove generator tensioner from water pump,
move tensioner aside.
18.Mark distributor position to front cover.
19.Remove distributor clamp, remove distributor.
See ELECTRICAL, Repair, Distributor - V8i
20.Remove fixings sump to front cover.
21.Loosen four adjacent sump fixings.
22.Remove generator support strut from front cover,
move strut aside.
23.Loosen remaining front cover fixings and remove
front cover.
24.Remove front cover gasket.Refit
25.Clean timing cover, clean block face.
26.Lightly grease gasket faces.
27.Fit new gasket to block face.
28.Apply hylosil to sump gasket.
29.Clean threads of cover fixing bolts, apply Loctite
372 to threads.
30.Fit timing cover, fit fixing bolts. Tighten to
28
Nm.
31.Fit generator support strut to front cover.
32.Tighten sump to timing cover fixings to
10 Nm.
33.Tighten sump fixings to10 Nm.
34.Lubricate distributor O ring.
35.Fit distributor in position marked.
36.Align oil pump drive, if distributor does not seat
correctly.
37.Fit distributor clamp. Tighten to
20 Nm.
38.Locate generator tensioner on water pump
bracket.
39.Connect heater hose, tighten clip.
40.Connect oil pressure switch.
41.Connect bottom hose, tighten clip.
42.Connect vacuum pipe to distributor.
43.Loosen power steering pump pivot, lower pump.
44.Connect distributor feed wire.
45.Connect wire ties to generator tensioner.
46.Fit power steering pump bracket to water pump.
Tighten to
28 Nm.
47.Fit power steering pump to bracket.
48.Position distributor cap. Fit plug leads to plugs
and clips.
49.Clip distributor cap in position.
50.Fit water pump pulley. Tighten to
10 Nm.
51.Fit crankshaft pulley.See Crankshaft Pulley
Assembly
52.Tension drive belts correctly.
53.Check ignition timing.
54.Refill cooling system.

12ENGINE
12
REPAIR
12.Ensure service tools LRT-12-010 and
LRT-12-091 are scrupulously clean. Coat seal
guide and oil seal journal with clean engine oil.
CAUTION: Do not handle oilseal lip, check
it is not damaged. Ensure outside diameter
remains clean and dry.
13.Position oil seal guide LRT-12-010 on crankshaft
flange.
NOTE: Lubricant coating must cover seal
guide outer surface completely to ensure
that oil seal lip is not turned back during
assembly. Position oil seal, lipped side towards
engine, on seal guide. Seal outside diameter
MUST be clean and dry.
14.Fit oil seal using tool LRT-12-091. Remove seal
guide.
15.Tighten rear main bearing cap to
90 Nm.
16.Fit sump.
17.Fit flywheel or flexible drive plate and ring gear.ENGINE
Service repair no - 12.41.01
Remove
1.Park vehicle on level ground and apply park
brake.
2.De-pressurise fuel system.
See FUEL
SYSTEM, Repair, Depressurising Fuel
System
3.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.Remove battery.See ELECTRICAL, Repair,
Battery
5.Remove radiator/oil coolers.See COOLING
SYSTEM, Repair, Radiator/Oil Coolers
6.Place an absorbent cloth around fuel feed hose
at fuel rail and release compression nut.
Remove feed hose from rail, seal end of pipes
with masking tape to prevent ingress of dirt.
7.Release fuel return hose clamp and remove
hose from pressure regulator, seal both
openings with masking tape to prevent ingress of
dirt.
8.Remove vacuum hose from rear of regulator.
9.Manual vehicles: Disconnect throttle cable from
bracket. Automatic vehicles: Detach throttle
bracket from plenum chamber and lay assembly
to one side.
See FUEL SYSTEM, Repair,
Plenum Chamber DO NOT DISTURB KICK
DOWN CABLE SETTING.
10.Remove ram housing.See FUEL SYSTEM,
Repair, Ram Housing
11.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
12.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
13.Remove Generator.See ELECTRICAL,
Description and operation, Generator
14.Release air conditioning compressor from its
mounting and lay to one side. DO NOT
discharge air conditioning system.
See AIR
CONDITIONING, Repair, Compressor

V8i
1
SERVICE TOOLS ENGINE
LRT-12-034 Spring compressor
MS1519A
LRT-12-010 Crankshaft rear seal guide
RO1014
LRT-12-052 Oil pressure test kit

4.0 V8
3
REPAIR ENGINE ASSEMBLY
Service repair no - 12.41.01/99
Remove
1.Position vehicle on ramp.
2.Remove bonnet.
See CHASSIS AND BODY,Repair, Bonnet [Hood]
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator
4.Remove plenum chamber.See FUEL SYSTEM
SFI, Repair, Plenum Chamber
5.Remove mass air flow sensor.See FUEL
SYSTEM SFI, Repair, Mass Air Flow Sensor
(MAF Sensor)
6.Slacken hose clip securing bottom hose to
expansion tank.
7.Disconnect hose.
8.Remove 2 nuts securing expansion tank.
9.Remove nut and bolt securing expansion tank.
10.Remove expansion tank.
11.Disconnect servo vacuum hose from ram
housing.
12.Disconnect battery sensing lead Lucar from
generator.
13.Remove generator terminal cover.
14.Remove 2 terminal nuts and release leads from
terminals.
15.Release purge hose from ram pipe housing.
16.Position cloth to absorb fuel spillage.
17.Slacken clip securing fuel return hose to fuel rail.
18.Disconnect hose.
19.Plug connections.
20.Disconnect fuel feed hose union.
21.Plug connections. Position hoses aside.
22.Slacken clip securing heater return hose to pipe.
23.Disconnect hose.24.Slacken clip securing heater feed adaptor hose
to inlet manifold.
25.Remove bolt securing pipe bracket.
26.Disconnect feed hose from inlet manifold.
27.Disconnect hose/pipe assembly.
28.Disconnect leads from spark plugs and remove
ignition coils.
See FUEL SYSTEM SFI, Repair,
Ignition Coils
29.Disconnect fuel temperature sensor multiplug.
30.Disconnect coolant sensor multiplug.
31.Disconnect temperature gauge sensor lead.
32.Release camshaft sensor multiplug from bracket
and disconnect multiplug.
33.Disconnect oil pressure switch Lucar.
34.Disconnect air intake temperature sensor
multiplug.
35.Disconnect 8 injector multiplugs.
36.Remove 4 nuts securing harness brackets to
inlet manifold.
37.Release harness brackets.
38.Remove bolts securing gearbox breather pipes
to engine lifting bracket.

4.0 V8
7
REPAIR 171.Route drive belt around pulleys.
172.Pivot tensioner downwards.
173.Align belt to tensioner and release tensioner.
174.Connect battery positive lead and tighten.
175.Secure terminal cover.
176.Align gearbox breather pipe, clip to engine lifting
eye and fit bolt. Tighten to
9 Nm.
177.Align and secure engine harness brackets to
inlet manifold and fit nuts. Tighten to
9 Nm.
178.Connect injector multiplugs.
179.Connect air intake temperature sensor multiplug.
180.Connect fuel temperature sensor multiplug.
181.Connect coolant temperature multiplug.
182.Connect temperature gauge connector.
183.Connect oil pressure switch Lucar.
184.Connect camshaft sensor multiplug and secure
to bracket.
185.Fit ignition coil bracket.
See FUEL SYSTEM
SFI, Repair, Ignition Coils
186.Position heater hose/pipe assembly.
187.Connect hose to inlet manifold.
188.Align pipe to bracket and fit bolt. Tighten to
9
Nm.
189.Tighten hose clip.
190.Connect heater return hose and tighten clip.
191.Remove plugs from fuel feed and return hose
connections.
192.Clean feed unions.
193.Connect return hose and tighten clip.
194.Connect feed hose union and tighten.
195.Remove cloth.
196.Connect purge hose.
197.Connect leads to generator, tighten terminal nuts
and fit cover.
198.Connect sensing Lucar.
199.Connect servo vacuum hose.
200.Position expansion tank and secure with fixings.
201.Connect hose and tighten clip.
202.Lower ramp.
203.Fit mass air flow sensor.
See FUEL SYSTEM
SFI, Repair, Mass Air Flow Sensor (MAF
Sensor)
204.Fit plenum chamber.See FUEL SYSTEM SFI,
Repair, Plenum Chamber
205.Fit radiator.See COOLING SYSTEM, Repair,
Radiator
206.Fit bonnet.See CHASSIS AND BODY, Repair,
Bonnet [Hood]
207.Reconnect battery negative lead.
208.Bleed power steering system.
See STEERING,
Repair, Power Steering System - Bleed
209.Drain engine oil and refill.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended Lubricants and Fluids - USA
Vehicles
210.Start engine. Check for fuel, coolant and oil
leaks.FRONT COVER GASKET
Service repair no - 12.65.04 - Front Cover Gasket
Remove
1.Disconnect battery negative lead.
2.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
3.Remove radiatorSee COOLING SYSTEM,
Repair, Radiator
4.Remove water pump pulley.See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
5.Slacken bottom hose clip. Remove hose from
water pump.
6.Raise vehicle on ramp.
7.Disconnect oil cooler hoses from front cover and
position aside. Plug hoses and connections.
8.Disconnect Lucar from oil pressure switch.

4.0 V8
9
REPAIR 28.Remove alignment tool LRT-12-090.
29.Apply a small amount of Loctite 242 to threads
and refit front cover bolts. Tighten to
22 Nm.
30.Fit sump bolts. Tighten to23 Nm.
31.Connect camshaft sensor multiplug.
32.Connect Lucar to oil pressure switch terminal.
33.Remove plugs from oil cooler pipes and cover.
34.Fit new 'O' ring seals, reconnect oil cooler pipes.
Tighten to
15 Nm.
CAUTION: Over tightening of oil cooler
pipe unions can crack front cover.
35.Refit bottom hose to water pump. Tighten clip.
36.Refit water pump pulley.
See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
37.Refit radiator assembly.See COOLING
SYSTEM, Repair, Radiator
38.Refill cooling system.See COOLING SYSTEM
V8, Adjustment, Coolant
39.Check/top-up engine oil.
40.Lower ramp.
41.Reconnect battery negative lead.

Mpi
3
DESCRIPTION AND OPERATION Lubrication
Oil is drawn from the pressed steel sump through a
strainer (1) and into the oil pump (2); excess pressure
being relieved by a pressure relief valve (3) integral
with the pump. The low oil pressure sensor (4)
registers the oil pressure in the main oil gallery on the
outflow side of the filter. Pressurised oil passes
through the full flow oil filter (5) to internal drillings in
the crankshaft where it is directed to each main
bearing and to the big end bearings via Nos. 1, 3 and
5 main bearings (6). An internal drilling in the cylinder
block directs oil, via a restrictor (7) to the cylinder
head where it passes through further internal drillings
to the hydraulic tappets and camshaft journals (8).
Gudgeon pin and small-end bush lubrication is by
splash from the big-end bearings.Crankcase ventilation
With the exception of two hoses connected from the
inlet camshaft cover to the inlet manifold and throttle
housing all crankcase ventilation is via internal voids
in the cylinder head and block. The inlet camshaft
cover carries a wire gauze flame trap located over the
breather pipe connections.