1995 LAND ROVER DISCOVERY oil pressure

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

Mpi
9
REPAIR 29.Disconnect oil pressure switch multiplug.
30.Disconnect air conditioning compressor
multiplug.
31.Remove 3 bolts securing engine harness to
manifold and fuel pipe.
32.Disconnect knock sensor multiplug.
33.Remove 2 nuts securing harness to starter motor
solenoid, remove harness.
34.Disconnect crankshaft sensor multiplug.
35.Disconnect fuel injection harness multiplug.
36.Disconnect inlet manifold air temperature sensor
multiplug.
37.Release clip and disconnect fuel hose from
pressure regulator.
CAUTION: Plug the connections.

Mpi
13
REPAIR 19.Connect crankshaft sensor, knock sensor, air
conditioning compressor, fuel injector harness,
inlet manifold air temperature and fuel
temperature sensor multiplugs.
20.Connect fuel hose to pressure regulator and
secure with clip.
21.Fit and tighten fuel pipe to fuel rail union.
22.Connect multiplugs to throttle housing.
23.Connect vacuum hose to manifold.
24.Connect oil pressure switch multiplug.
25.Connect brake servo hose to manifold, secure
with clip.
26.Connect throttle cable to cam.
27.Position engine harness and connect breather
hose to inlet manifold, secure with clip.
28.Connect coolant temperature sensor multiplugs,
secure harness with cable tie.
29.Connect oxygen sensor multiplug, secure
harness with cable tie.
30.Connect alternator harness.
31.Connect heater hose to heater rail and secure
with clip.
32.Connect hose to coolant pump and secure with
clip.
33.Connect inlet hose to power steering pump and
secure with clip.
34.Fit and tighten outlet pipe union to power
steering pump.
35.Connect bypass and top hose, secure with clip.
36.Connect air cleaner to throttle housing hose and
secure with clip.
37.Remove engine lifting bracket.
38.Position spark plug cover and secure with
screws.
39.Fill engine with oil.
40.Fit bonnet [hood].
See CHASSIS AND BODY,
Repair, Bonnet [Hood]
41.Fit radiator.See COOLING SYSTEM, Repair,
Radiator - Mpi
42.Adjust throttle cable.See FUEL SYSTEM,
Adjustment, Throttle Cable Adjustment
ENGINE SUMP GASKET
Service repair no - 12.60.43
Remove
1.Drain engine oil.
2.Refit drain plug, use new sealing washer if
necessary, tighten to the correct torque.
3.Remove 18 bolts securing sump.
NOTE: 25mm long bolt is fitted at rear L.H.
corner of sump.
4.Release sump from cylinder block.
5.Discard gasket.

12ENGINE
14
REPAIR Refit
1.Clean sump, remove all traces of gasket from
mating faces of sump and cylinder block.
Visually check sump for damage.
2.Apply beads of RTV sealant to front main
bearing cap.
3.Position new gasket to sump, ensuring that
location pips on gasket are located in sump.
Check gasket lays flat on sump flange.
4.Fit sump. Fit bolts, ensuring that longest bolt is
inserted at position 7.
5.Working around the sump in the sequence
illustrated, tighten the bolts to the stage 1 torque
figure. Then, in the same sequence, tighten the
bolts to the stage 2 torque figure.
NOTE: For torque values.See
Specifications, torque, Torque Values
6.Fill engine with oil.CYLINDER HEAD GASKET
Service repair no - 12.29.01
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve pressure.
CAUTION: Plug the connections.
WARNING: Do not carry out the next
instruction until the coolant is cool to
avoid personal injury from scalding.
3.Release clip and disconnect radiator bottom
hose, allowing coolant to drain into a suitable
container.

Mpi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
ENGINE
Timing belt upper cover bolts 5......................................................................
Timing belt centre cover bolts 5.....................................................................
Timing belt lower cover bolts 5......................................................................
Crankshaft pulley centre bolt 85.....................................................................
Crankshaft pulley to timing gear bolts 10........................................................
Tensioner pulley bolt 30..................................................................................
Spark plugs 27................................................................................................
Timing belt upper backplate bolts 10..............................................................
Camshaft gear bolts 65...................................................................................
Exhaust camshaft rear oil seal cover plate bolts 10........................................
Inlet camshaft rear oil seal cover plate bolts 10..............................................
Crankshaft rear oil seal housing bolts 10........................................................
Engine sump bolts
Stage 1 3...............................................................................................
Stage 2 10..............................................................................................
Bell housing nuts 40........................................................................................
L.H. and R.H. engine mounting nuts 85..........................................................
Exhaust manifold to downpipe nuts 10...........................................................
Exhaust downpipe to silencer box nuts 30......................................................
Air conditioning compressor to engine block bolts 45.....................................
Cylinder head bolts
Stage 1 45..............................................................................................
Stage 2 80..............................................................................................
Stage 3 - Further 90°
Camshaft cover bolts 10.................................................................................
Knock sensor 15.............................................................................................
Ignition coil bracket bolts 25............................................................................
Coolant temperature sensor 15......................................................................
Crankshaft sensor bolts 7..............................................................................
Fuel temperature sensor 7.............................................................................
Intake air temperature sensor 7.....................................................................
Fuel rail to inlet manifold bolts 10...................................................................
Fuel feed hose stiffening bracket bolts 7.......................................................
Throttle housing mounting nuts 7...................................................................
Fuel pressure regulator steady bracket bolts 7..............................................
Oxygen sensor 55...........................................................................................

EMISSION CONTROL
1
DESCRIPTION AND OPERATION REV: 09/95 EMISSION CONTROL
Three systems are used to control the vehicle
atmospheric emissions these are:
Engine crankcase fume emissions.
Fuel tank Evaporative emissions
Engine exhaust gas emissions.
Crankcase ventilation system - 3.9 MFi models
only
The crankcase ventilation system which is an integral
part of the air supply to the engine combustion
chambers, is often overlooked when diagnosing
problems associated with engine performance. A
blocked ventilation pipe or filter or excessive air leak
into the inlet system through a damaged pipe or
leaking gasket can effect the mixture, performance
and economy of the engine.
1. Three way connector
2. Air filter
3. Oil separatorThe purpose of the crankcase ventilation system is to
ensure that any noxious gas generated in the engine
crankcase is rendered harmless by burning in the
combustion chambers as follows:
Oil laden noxious gas in the engine crankcase is
drawn through an oil separator 3 located on the right
cylinder head rocker cover, where the oil is separated
and returned to the sump. The gas flows through a
restrictor in the three way connection 1 and into the
inlet plenum chamber where it is drawn into the
combustion chambers and burned. The volume of
fresh air which is drawn from the atmospheric side of
the throttle butterfly to mix with the gas, depends on
the position of the throttle and the engine speed.
The air filter 2 fitted to the left cylinder head rocker
cover, must be maintained in clean condition to
ensure sufficient air enters the crankcase under
varying throttle openings and manifold depression, to
prevent excessive crankcase pressure or depression
developing.

19FUEL SYSTEM
4
REPAIR TURBOCHARGER ACTUATOR
Service repair no - 19.42.31
Remove
1.Remove exhaust manifold and turbocharger.
See MANIFOLD AND EXHAUST SYSTEM,
Repair, Exhaust Manifold - Tdi
2.Remove 2 nuts securing the actuator to the
turbocharger bracket.
3.Release clip and disconnect hose from actuator.
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove turbocharger actuator.
Refit
6.Fit the replacement actuator and secure with
nuts.
7.Push the control lever as far as possible towards
the actuator and apply pressure to keep the
lever in this position.
8.Pressurise the actuator to 57 - 62 cm Hg and
hold this pressure.
CAUTION: Use only the threaded end of
the lever to make adjustments. Forcing the
complete lever in or out will change the
calibration with the possibility of damaging engine
boost.
9.Screw the lever in either direction until the eye
on the end will locate easily over the wastegate
spindle and secure with a new clip.
10.Release the pressure and tighten the locknut.
11.Refit exhaust manifold and turbocharger.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
TURBOCHARGER AND GASKET
Service repair no - Turbocharger - 19.42.01
Service repair no - Gasket - 19.42.25
Remove
1.Disconnect battery negative lead.
2.Remove air cleaner assembly.
See Air Cleaner
3.Remove exhaust manifold assembly.See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove 4 bolts and 2 clamp plates securing
turbocharger to exhaust manifold.
6.Remove turbocharger and discard gaskets.
Refit
7.Clean mating faces of turbocharger and exhaust
manifold.
8.Reverse removal procedure. Use new clip to
secure control lever to wastegate spindle.
Tighten to
45 Nm.
9.Check/top-up engine oil level.