1995 LAND ROVER DISCOVERY air filter

GENERAL SPECIFICATION DATA
5
INFORMATION FUEL SYSTEM 3.9 V8i
Fuel system type Lucas 14CUX hot wire system electronically controlled..............................................................
Fuel pump-make/type ACX delco high pressure electrical, immersed in the......................................................
fuel tank
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Airflow Sensor
Make and type Lucas 'Hot Wire' 5AM.................................................................
Injectors
Make and type Lucas 8NJ.................................................................
Electronic Control Unit
Make and type Lucas 14CUX.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................
Coolant temperature sensor
Make and type Lucas 3TT.................................................................
Bypass Airvalve (Stepper motor)
Make and type Lucas 2ACM.................................................................
Throttle potentiometer
Make and type Lucas 215SA.................................................................
Lambda sensor - catalyst vehicles
Make and type Lucas 3LS.................................................................

04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

MAINTENANCE
7
MAINTENANCE
CHECK/ADJUST VALVE CLEARANCES. - Tdi
Valve adjustment.See GENERAL SPECIFICATION
DATA, Information, 300 Tdi Engine
RENEW FUEL FILTER ELEMENT - Tdi
Drain off water and sediment
CAUTION: It is essential that any water
and sediment in fuel filter is drained off, as
water in fuel can result in damage to
injection pump.
1.Hold a small receptacle beneath drain cock.
Unscrew the drain cock half a turn.
2.Drain off water and sediment.
3.Tighten the drain cock immediately fuel starts to
flow from drain cock.
NOTE: Any delay in tightening drain cock
when fuel starts to flow could possibly
mean bleeding fuel system.
Renew fuel filter element
1.Clean area around filter, place a container
beneath.
2.Unscrew filter, a quantity of fuel will be released,
and discard filter.
3.Wet seal of new filter with fuel.
4.Screw new filter into position.
5.Ensure that drain cock is secure.
RENEW AIR CLEANER ELEMENT V8i CATALYST
Mpi - Tdi - V8i NON CATALYST
To renew air cleaner element - V8i, Mpi,Tdi
See FUEL SYSTEM, Repair, Air Cleaner

10MAINTENANCE
12
MAINTENANCE
EXTERNALLY CHECK INTERCOOLER FOR
OBSTRUCTION - Tdi
Clear any trapped dirt or flies from vanes of
intercooler
CLEAN INTERCOOLER ELEMENT - Tdi
Remove
1.Remove intercooler element.
2.Flush intercooler with ICI 'GENKLENE'or
à oD-SOLVE' propriety cleaner, following the
manufacturer's instructions.
3.Dry the intercooler completely ensuring that no
liquid remains in the element.
Refit
4.Refit intercooler element.UNDER VEHICLE MAINTENANCE
Vehicles operating under severe conditions of dust,
sand, mud and water should have oils changed and
lubrication carried out at more frequent intervals than
is recommended in maintenance schedules.
RENEW ENGINE OIL AND FILTER - Tdi
CAUTION: Serious damage to the
turbocharger will result if engine is run
above idling speed before oil pressure is
restored.
RENEW ENGINE OIL - V8i
RENEW ENGINE OIL AND FILTER - V8i
CAUTION: To prevent an airlock occuring
after removing filter, fill new filter with oil
and fit immediately after removing old
filter. If airlock does occur fill oil pump with
petroleum jelly.
RENEW ENGINE OIL AND FILTER - Mpi
CHECK/TOP UP MANUAL GEARBOX OIL - V8i
1.Site vehicle on lift or level ground.
2.Remove oil filler level plug. If necessary, inject
new oil into the gearbox until it runs out of filler
hole. Fit plug. Tighten to
30 Nm.
RENEW MANUAL GEARBOX OIL - Tdi - Mpi
RENEW MANUAL GEARBOX OIL - V8i

MAINTENANCE
17
MAINTENANCE
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN FUEL SEDIMENTER - Tdi
Fuel sedimenter
The sedimenter is attached to left-hand side of
chassis frame near fuel tank. It increases the working
life of the fuel filter by removing larger droplets of
water and larger particles of foreign matter from fuel.
Drain off water
1.Loosen drain plug, allow water to run out.
Tighten plug immediately pure diesel fuel starts
to flow.
RENEW FUEL FILTER
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction regarding fuel handling are
strictly adhered to when carrying out following
instructions.
See INTRODUCTION, Information,
Fuel Handling Precautions
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
1.Depressurise fuel system.
See FUEL SYSTEM,
Repair, Depressurising Fuel System
2.The fuel line filter is located on right hand
chassis side member forward of fuel tank filler
neck. Access to filter is gained through right
hand rear wheel arch.
3.Thoroughly clean area around hose connections
to prevent ingress of foreign matter into fuel
system.
4.Loosen two fuel unions and remove hoses from
filter canister.
5.Release securing bolt and bracket, remove filter
from chassis side member.
6.Fit a new filter observing direction of flow arrow
on canister.
7.Fit inlet and outlet hoses. Tighten to
30 Nm.
8.Refit fuel pump relay.
9.Reconnect battery negative lead.
10.Recode radio.
11.Start engine and inspect hose connections for
fuel leaks.

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

12ENGINE
4
REPAIR 22.Disconnect feed pipe and spill return pipe from
injector pump.
23.Disconnect both pipes from fuel lift pump.
24.Disconnect servo hose from vacuum pump.
25.Remove three retaining nuts and disconnect
exhaust down pipe.
26.Remove oil cooler pipes from oil filter adaptor.
27.If automatic transmission is fitted, disconnect
feed and return pipes at gearbox oil cooler.
Remove retaining bracket from LH side of
cylinder block and release both oil cooler pipes.
28.Support gearbox.
29.Disconnect ground strap from starter motor.
30.On vehicles with automatic transmission, remove
fixings and detach drive plate housing access
panel and gasket.31.Working through drive plate housing aperture
mark the torque convertor and drive plate to
facilitate reassembly.
32.Remove the four convertor to flexible drive
securing bolts, rotating crankshaft to gain access
to each individual bolt.
33.Fit engine lifting bracket to the two RH rear
cylinder head fixing bolts.
34.Using suitable hoist, fit lifting chains to engine.
35.Remove four bolts, from both sides, securing
front engine mounting brackets to cylinder block.
36.Remove two bolts, from both sides, securing
front engine mounting bracket to bell housing.